Contact Us

INA2137UA-2K5

Brand: Texas Instruments
Texas Instruments INA2137UA-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2137UA-2K5 — Power Management & Signal Chain | Superb Automation

INA2137UA-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2137UA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2137UA-2K5: the plus or minus 6 dB receiver on a 2500 piece reel

INA2137UA-2K5 is the dual audio differential line receiver with a fixed plus or minus 6 dB gain, in the fourteen pin SOIC on a 2500 piece large reel. The gain is 0.5 or 2 depending on which input the signal is applied to, the bandwidth is 4.0 megahertz, the distortion is 0.0005 per cent and the noise floor is minus 106 dBu.

Only the reel is published for this part; there is no tube row in the addendum, so a prototype quantity has to come from a cut reel. The electrical rows are the 6 dB receiver's: 90 dB typical of rejection at 46.5 volts of common mode, 100 microvolts typical of offset, 2.4 milliamps per amplifier and a supply of plus and minus 4 to plus and minus 18 volts.

INA2137UA-2K5 as the vendor document publishes it

Channels2
Gain0.5 or 2 V/V, plus or minus 6 dB by connection
Supplyplus or minus 4 to plus or minus 18 volts
Quiescent current2.4 milliamps typical, 2.9 maximum per amplifier
Distortion0.0005 per cent total harmonic distortion plus noise at 1 kilohertz, 10 volts RMS
Noise floorminus 106 dBu over a 20 kilohertz band
Headroomplus 23 dBu at 1 per cent distortion
Bandwidth and slew4.0 megahertz, 14 volts per microsecond
Offset voltage100 microvolts typical, 1000 maximum
Offset drift2 microvolts per degree
Rejection74 minimum, 90 typical decibels at 46.5 volts of common mode
Gain error0.01 typical, 0.1 maximum per cent
Power supply rejection5 microvolts per volt typical, 60 maximum
Input network12 kilo-ohms and 6 kilo-ohms, ratio matched
Temperature rangeminus 40 to plus 85 degrees
Vendor statusactive, 2500 piece large reel
Catalogue codeINA2137UA-2K5
Vendor stringINA2137UA/2K5
Carrierlarge reel of 2500, 330 millimetre
Moisture levellevel 3, 260 degrees, 168 hour floor life

Plus or minus six decibels by connection

INA2137UA-2K5 is the other gain option in the audio line receiver family: a fixed plus or minus 6 dB, which is a gain of 2 or a gain of 0.5 depending on which input the signal is applied to. The network is 12 kilo-ohms and 6 kilo-ohms, trimmed as a pair, and the bandwidth is 4.0 megahertz with a slew rate of 14 volts per microsecond.

The 0.5 connection is the one that gets used. A balanced output from a console can run at plus 20 dBu, and an input stage that has to survive it without clipping needs either a pad or a receiver with 6 dB of loss. The 2 connection is for a low level source, such as a moving coil pickup or a passive summing bus, where 6 dB of gain ahead of the converter removes a stage.

Point zero zero zero five per cent, and a noise floor six decibels lower

The distortion of INA2137UA-2K5 is 0.0005 per cent at 1 kilohertz with a 10 volt RMS input, the same row as the 0 dB member, and the noise floor is minus 106 dBu over a 20 kilohertz bandwidth against minus 100 on that part, because the 6 dB of loss comes ahead of the amplifier and takes the input noise with it. Headroom is plus 23 dBu at 1 per cent distortion.

That 6 dB difference is the useful part of the comparison. A receiver with 0.5 gain attenuates whatever noise arrives on the line by 6 dB as well, so on a short cable the two parts are equivalent, and on a long cable the 0.5 part is quieter at the output for the same input noise. What it cannot do is recover a signal that is already below the converter floor, and that case needs the 2 connection rather than a quieter receiver.

Ninety decibels at forty six and a half volts

The common mode rejection of INA2137UA-2K5 is 74 dB minimum and 90 dB typical, measured at 46.5 volts of common mode with a source impedance of zero, which is the widest window in the family because the input divider is 12 kilo-ohms and 6 kilo-ohms and the part is rated to plus and minus 18 volts of supply.

A receiver that accepts 46 volts of common mode is one that survives a fault. A miswired cable that puts a 48 volt phantom supply on the input, or a chassis that floats 30 volts above the console ground, will not damage the part and will not put more than a few millivolts on the output. At the minimum of 74 dB, 46 volts becomes 9 millivolts, which is loud but not destructive, and at the typical 90 dB it is 1.5 millivolts.

The offset and the gain error in the 6 dB path

The offset of INA2137UA-2K5 is 100 microvolts typical and 1000 maximum at 25 degrees, the drift is 2 microvolts per degree, and the power supply rejection is 5 microvolts per volt typical against 60 maximum over plus and minus 4 to plus and minus 18 volts. The gain error is 0.01 per cent typical and 0.1 maximum over plus and minus 10 volts of output, which is tighter than the 0 dB member because the divider is a smaller ratio.

In the 0.5 connection the offset at the input is attenuated by 6 dB along with the signal, so 1 millivolt of input offset becomes 0.5 millivolts at the output, and in the 2 connection it is doubled. That asymmetry is the practical reason to pick the connection before the coupling capacitor: a DC coupled path in the 2 connection carries twice the offset of the 0.5 connection, and the converter behind it sees the difference.

The same supplies and the same two point four milliamps

INA2137UA-2K5 runs from plus and minus 4 to plus and minus 18 volts and draws 2.4 milliamps typical and 2.9 maximum per amplifier, the same rows as the rest of the family. The output stage is the same wide swing stage, and the part is specified over minus 40 to plus 85 degrees.

Because the two receivers share a package, a board can carry one of each and route the hot signal to the 0.5 connection and the low level one to the 2 connection without a second part number on the bill of materials. That is the practical use of having both: four channels of input on two packages, with the gain chosen per channel by wiring rather than by ordering a second device.

Where the 6 dB receiver belongs

INA2137UA-2K5 belongs on an input that has to accept a hot balanced line without a pad, on a summing bus that needs 6 dB of gain before a converter, and on any channel where the level is known and a fixed loss or a fixed gain is cheaper than a switchable one. The 46 volt common mode window also makes it the safer choice for a field input that can be miswired.

It does not belong where the level is unknown, because a fixed 6 dB cannot be changed at run time. It does not belong on a single 5 volt rail. It does not belong where the source impedance is above 50 kilo-ohms, because that is the input network. And it does not belong in a DC instrumentation channel, where a 1 millivolt offset and a 2 microvolt per degree drift are worse than the parts built for that job. Our amplifier cross reference page covers both receiver gains and the unity gain parts, and the vendor consolidation page covers holding one receiver code across several boards.

The gain connection is made on the board, so the board wiring decides before the reel does. Our amplifier cross reference page covers both receiver gains, and the BOM scrubbing page covers the input wiring against the bill of materials.

How is the gain chosen? By which input the signal drives: one connection gives 0.5 and the other gives 2, from the same 12 kilo-ohm and 6 kilo-ohm network.

Is there a tube? Not in the current addendum. The published row is the 2500 piece large reel, so a small quantity comes from a cut reel.