Contact Us

INA2126E-250

Brand: Texas Instruments
Texas Instruments INA2126E-250 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2126E-250 — Power Management & Signal Chain | Superb Automation

INA2126E-250

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2126E-250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2126E-250: two channels on a 250 piece reel, with the slash printed by the vendor

INA2126E-250 is the two channel instrumentation amplifier in the 16 pin SSOP, on a 250 piece small reel. It draws 175 microamps per channel from a supply that starts at 1.35 volts, holds 250 microvolts maximum of offset with 3 microvolts per degree of drift, and sets each channel's gain from 5 to 10 000 with its own resistor.

The code needs one reading note: the vendor prints this row as INA2126E/250 with a slash and our catalogue uses a hyphen in the same place. Both describe the same 250 piece small reel at moisture level 2 with a one year floor life. The E grade is the tighter of the two orderable rows, and the EA grade beside it is printed at moisture level 3 with a 168 hour floor life instead. Two channels in one package also means one reel covers a board that measures two sensors, which is how the part is normally bought: 250 pieces is 500 channels, enough for a pilot instrument and its spares.

INA2126E-250 as the vendor document publishes it

Channels2
Quiescent current175 microamps per channel
Supply range1.35 volts to 18 volts
Offset voltage250 microvolts maximum
Offset drift3 microvolts per degree maximum
Common mode rejection80 dB minimum, 94 dB typical
Power supply rejectionquoted in microvolts per volt from 1.35 to 18 volts
Input bias current25 nanoamps maximum
Voltage noise35 nanovolts per root hertz
Gain5 to 10 000 V/V, one external resistor per channel
Temperature rangeminus 40 to plus 85 degrees
BodySSOP, 16 pin, DBQ
Vendor statusactive, 250 piece small reel
Catalogue codeINA2126E-250
Vendor stringINA2126E/250, printed with a slash
GradeE, moisture level 2
Marking2126E
Moisture levellevel 2, 260 degrees, one year floor life

A hundred and seventy five microamps per channel

INA2126E-250 is a two channel instrumentation amplifier that draws 175 microamps per channel, so a dual package costs 350 microamps for two independent front ends. The supply range of 1.35 to 18 volts is the widest in this group and covers a single alkaline cell as well as a 15 volt industrial rail.

The two op amp architecture is what makes the current draw possible. It is not a three op amp instrumentation amplifier, so the input stage has a common mode range that stops short of the rails and the rejection is lower, and in exchange the part runs from 1.35 volts and draws a fraction of what a three op amp part needs. For a portable instrument with two sensors and a coin cell budget, that trade is the whole reason the part exists, and it is also why the part turns up in a four to 20 milliamp transmitter that has to take its supply from the loop current: 350 microamps for two channels leaves the converter and the reference room to work.

Two hundred and fifty microvolts, three microvolts per degree

The offset of INA2126E-250 is 250 microvolts maximum with a drift of 3 microvolts per degree maximum, and the bias current is 25 nanoamps maximum. The temperature range is minus 40 to plus 85 degrees, which is narrower than the rest of this group and is the first row to check on an industrial application.

The 3 microvolts per degree is the row that matters over that window: 125 degrees of range gives 375 microvolts of drift, larger than the maximum offset itself. A channel that calibrates at room temperature and runs at 85 degrees therefore has about 600 microvolts of total offset, which on a 10 millivolt bridge is six per cent. On a 200 millivolt span it is a third of a per cent, and there the part is the cheapest way to get two channels of differential amplification.

Gain from five to ten thousand on one resistor

The gain of INA2126E-250 is set by a single resistor from 5 to 10 000, with the internal network trimmed at a gain of 5 in the same way as the single channel part. Two channels share the package but not the gain resistor: each channel brings out its own pins, so a dual can run two different gains.

That is convenient for a two sensor instrument, and it is also a trap for a bill of materials: the two resistors are separate components with separate tolerances, so a dual used at two gains has two gain errors rather than one. A production build that needs matching channels is better served by two resistors from the same reel and the same tolerance band, or by a part with a fixed gain on both channels.

Eighty decibels of rejection, and the input window that goes with it

The common mode rejection of INA2126E-250 is 80 dB minimum and 94 dB typical, and the power supply rejection is quoted in microvolts per volt over the 1.35 to 18 volt range. The two op amp architecture puts the input window inside the rails rather than at them.

Eighty decibels turns a 1 volt common mode into 100 microvolts at the input, which is under the 250 microvolt offset, so the two error terms are balanced and neither dominates. The window is the limit that matters more: a ground referenced sensor on a single 1.35 volt rail has almost no headroom, and a bridge that sits at half rail is the natural application. A high side shunt on a 12 volt bus is outside the window on any supply the part can take, and so is a sensor whose common mode sits at the positive rail. The window is also the row that improves with the supply: on 18 volts the part has the headroom a plus or minus 10 volt signal needs, and on 1.35 volts almost all of the range is taken by the amplifier's own operating point.

Thirty five nanovolts and twenty five nanoamps

The voltage noise of INA2126E-250 is 35 nanovolts per root hertz and the bias current is 25 nanoamps maximum, which pairs the part with sources of a few kilo-ohms. On a 350 ohm bridge the source noise is 1.7 nanovolts and the amplifier dominates; on a 100 kilo-ohm source 25 nanoamps of bias current gives 2.5 millivolts of offset, ten times the published maximum.

That is the arithmetic a two op amp front end forces on the board: the bias current is the price of the low supply current, and a high impedance sensor needs either a lower bias part or a buffer ahead of it. For a bridge, an RTD or a thermopile the 25 nanoamps are harmless, and the 35 nanovolts are quiet enough that a 16 bit converter is limited by its own reference rather than by the front end.

Two channels in one package, and where that fits

INA2126E-250 belongs in a portable two channel instrument, a level or flow transmitter with a temperature compensation channel, a patient monitor with two differential inputs, an infusion pump with a pressure and a force channel, and any board where 350 microamps for two front ends is the difference between a coin cell and a battery pack.

It stops at three things. The temperature range ends at plus 85 degrees, so an industrial module that runs hot needs a different part. The common mode window sits inside the rails, so a high side sensor needs a divider or a different front end. And the 250 microvolt offset belongs to a large signal channel rather than to a load cell, where a chopper part is the answer. Our amplifier cross reference page covers the single channel member of the family, and the vendor consolidation page covers buying the two channels and the single on one line.

The grade, the carrier and the slash are the three fields to check on this row. Our BOM scrubbing page covers the code against the bill of materials, and the amplifier cross reference page covers the single channel member of the family.

Is this the same part as INA2126E/250? Yes. The vendor prints a slash and our catalogue prints a hyphen; the reel and the marking are the same.

Do the two channels share a gain resistor? No. Each channel brings out its own pins, so a dual can run two different gains.