Contact Us

TPSM63606RDLR

Brand: Texas Instruments
Texas Instruments TPSM63606RDLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM63606RDLR — Power Management & Signal Chain | Superb Automation

TPSM63606RDLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM63606RDLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM63606RDLR: 36 V input 6 A synchronous buck module with adjustable frequency

TPSM63606RDLR is a 6 A step down module that keeps the MOSFETs, inductor and controller inside a 5 by 5.5 mm overmoulded package in a B3QFN (RDL) body of 20 pins. It takes 3 V to 36 V in and delivers 1 V to 16 V out, which is a wider output window than the 3 A member of the same family, and the switching frequency is set by one resistor anywhere from 200 kHz to 2.2 MHz. The S suffix adds spread spectrum modulation for emission compliance.

Order code and package

Order code read outTPSM63606 RDL R: module TPSM63606, RDL twenty pin B3QFN, R large tape and reel
PackageB3QFN (RDL), 20 pins, 5.0 mm by 5.5 mm by 4.0 mm, four thermal pads under the body
Carrier in the vendor addendumTPSM63606RDLR and TPSM63606SRDLR, both 1000 pieces on a large reel; the SRDLR row is the spread spectrum version
Moisture levelLevel 3, 250 degrees peak reflow, 168 hour floor life
Lead finishNickel palladium gold
RoHS statusExempt on the rows published, which is not the same as a green material declaration
Operating junction rangeminus 40 to plus 125 degrees, with absolute maximum at 150 degrees

Electrical parameters that decide the application

Input voltage range3.95 V needed to start, then 3 V to 36 V once running, so a 24 V rail with dips still holds regulation
Output voltage range1 V to 16 V, set by a divider against a 1 V reference
Output current6 A at 25 degrees, with the note that continuous current derates at high frequency and high ambient
Switching frequency200 kHz to 2.2 MHz set by one resistor from the RT pin, and the default with a 66.5 k resistor is about 1.98 MHz
High side current limit8.3 A typical, which is the figure that protects the module rather than the load
Negative current limit8.3 to 10.3 A, so the module can sink current in a pre-biased or forced start
Hiccup threshold6.5 to 7.7 A, with an 80 ms wait before the module retries
Feedback accuracyplus or minus 1 percent over temperature at light load, which is tighter than the 3 A member
Shutdown current0.6 uA typical, the number that matters for a battery product left in storage
Internal biasAn internal LDO from the VLDOIN pin, which can be fed from the output for higher efficiency at high duty
Spread spectrumA 2 percent frequency span on the S version, which is the variant to order when the emission test is tight
Absolute maximum42 V on the input pins, 16 V on the feedback pin, 20 V on power good

Family variants and how they differ

TPSM63606RDLRthe standard version, fixed frequency set by the RT resistor
TPSM63606SRDLRthe same die with spread spectrum modulation enabled, ordered when conducted and radiated emissions need the extra margin
TPSM53603the 3 A member of the same package family, same 36 V input, output limited to 7 V
VLDOIN pinallows the internal bias to come from the output instead of the input, which lifts efficiency when the duty cycle is high
Negative outputsupported by the family, which is how a bipolar rail is built from one module type

Points to check before this part goes on a BOM

The frequency resistor is the main tool for trading size against loss. At 2.2 MHz the module can use a very small output capacitor and stay clear of the AM band, at the cost of switching loss, and at 400 kHz the same 6 A runs cooler with a larger output capacitor and a lower emission floor at high frequency. The default 1.98 MHz suits a compact board, and the 6 A figure in the electrical table is quoted at 800 kHz with a 3.3 V output, so a 2.2 MHz build should be checked against the derating note rather than the headline.

The spread spectrum version is not a cosmetic difference. A 2 percent span swept at about 1.5 Hz smears the switching harmonics and typically buys several dB at the peak, which is often the difference between passing and failing a CISPR 11 or CISPR 32 class B scan on a first attempt. The suffix has to be ordered deliberately, because the standard part and the S part are separate order codes on the same reel size.

The 8.3 A high side limit on a 6 A module is about 38 percent of margin, and the negative limit is the same order of magnitude, which matters in a buck that has to absorb current from a pre-charged output or an inductive load. When the current reaches the hiccup threshold the module waits 80 ms before retrying, so a shorted output produces a visible burst pattern rather than a steady thermal event.

Feeding VLDOIN from the output rather than the input is worth the extra trace on a high duty build. The internal bias current comes from the lowest available rail, so at 36 V in and 12 V out the difference in bias loss is several tens of milliwatts, and at 5 V out it is larger still. The pin has an absolute maximum of the lower of input plus 0.3 V and 16 V, so a 12 V output can feed it while a 16 V output cannot.

The package has four thermal pads rather than one, which spreads the heat and lowers the peak junction for the same board area. That is the reason the 6 A part shares a footprint with the 3 A part without doubling the copper requirement. Solder voiding under those pads is the most common cause of a module that regulates correctly on the bench and folds back inside a closed enclosure.

Where this order code fits

Used where one module has to cover a range of outputs from a 12 V, 24 V or 36 V bus: industrial controllers, test instruments, telecom line cards, motor drive logic supplies and medical carts that need a 5 V, 12 V or 15 V rail from a wide input with few external parts. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What frequency should be chosen? Start from the emission limit and the output ripple requirement. If the board must stay clear of a band, run at 2.2 MHz; if efficiency at high ambient is the constraint, run nearer 400 kHz. The resistor table in the data sheet gives the value for each step.

Does the S suffix change the pin out? No. The SRDLR is the same 20 pin body and the same land pattern, with spread spectrum active inside. Only the order code and the emission signature change.

Can it produce a negative rail? Yes, the family supports a negative output, which is how a split supply is built from one module type. The feedback divider is then referenced to the negative rail rather than to ground.

Why does the input need 3.95 V to start but only 3 V to run? The higher start threshold guarantees the internal bias and the gate drive are valid before switching begins, and the lower running threshold gives margin for a supply that sags once the load is applied.

How is a 6 A module handled in reflow? Level 3 at 250 degrees with a 168 hour floor life, so the reel has to be dry packed and the parts baked if the floor life is exceeded. The four pads need a stencil aperture that avoids large voids.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.