Contact Us

TPS65988DHRSHR

Brand: Texas Instruments
Texas Instruments TPS65988DHRSHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65988DHRSHR — Power Management & Signal Chain | Superb Automation

TPS65988DHRSHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65988DHRSHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65988DHRSHR: dual port USB Type-C and PD 3.0 controller with integrated power paths

TPS65988DHRSHR is a two port USB Type-C power delivery controller with the high voltage power switches on the die in a VQFN (RSH) body of 56 pins. It integrates two 5 V to 20 V, 5 A, 25 milliohm bidirectional power paths, the cable detection and VCONN switches, the policy engine for PD 3.0, BC1.2 charging support and 13 general purpose pins for mux and mode control.

Order code and package

Order code read outTPS65988 D HRSH R: family, D variant, RSH 56 pin VQFN 7 mm by 7 mm, R tape and reel
PackageVQFN (RSH), 56 pins, 7.00 mm by 7.00 mm, two thermal pads, one for the controller and one for the FETs
Carrier2500 pieces on a large reel
Life cycle statusNRND, not recommended for new builds, in the vendor addendum dated for this revision
Operating temperatureminus 10 to plus 75 degrees Celsius ambient, which is narrower than the industrial range usually assumed
CertificationUSB PD 3.0 certified, USB Type-C specification certified, IEC 62368-1 certificate US-34617-UL
Interfacesone I2C port usable as primary or secondary, one primary only I2C port, SPI controller, 13 configurable GPIOs

Electrical parameters that decide the application

High voltage pathsPP_CABLE and PP_HV, 4 V to 22 V operating, two paths rated 20 V at 5 A with 25 milliohm switches
VIN_3V33.135 V to 3.45 V, the controller supply
VBUS sense0 V to 5.5 V on the VBUS pins, separate from the power path rating
I/O levelsCx_CC1 and Cx_CC2 rated to plus or minus 10 V against a 5.5 V supply rail, USB data pins to 3.6 V
Current monitoringPP_CABLE current limit at 3.4 A nominal in the accuracy row used for cable compensation
Dead batteryan internal 3.3 V LDO keeps the controller alive with no battery, so a phone charges from a flat pack
Cable handlingattach and orientation detection with an integrated VCONN switch per port
Thermaljunction limit 125 degrees, thermal shutdown with hysteresis, junction to case 0.7 degrees per watt on the FET pad
GPIO count13 configurable pins for mux control, retimers, status LEDs and mode selection
I2C topologyone port usable as primary or secondary, one primary only port, plus a SPI controller

Family variants and how they differ

TPS65988the dual port part on this page, two independent PD ports in one controller
Single port family membersTPS65987 and its relatives cover one port with fewer pins
D and DH variantsthe letter block selects the firmware image and the supported alternate modes
RSH body56 pins with separate controller and FET thermal pads, which is what allows 5 A per port without an external hot swap device
StatusNRND, so new builds should look at the current generation part even though the die is capable

Points to check before this part goes on a BOM

This order code is NRND. The vendor addendum marks TPS65988DHRSHR as not recommended for new builds. That is a procurement fact, not a quality judgment: the part works to its specification, but a customer starting a new platform should be told before the board file is frozen, and a repair or legacy build can still use it. That status is a lifecycle term from the vendor rather than a comment on how the device performs.

The ambient range is minus 10 to plus 75 degrees, not minus 40. A USB PD controller in an industrial enclosure or an outdoor terminal will exceed that on a hot day once the 5 A paths are loaded, and the junction limit of 125 degrees is the only remaining margin. Thermal work has to be done on the FET pad, because that is where 25 milliohm at 5 A turns into 0.63 W per port.

Two ports at full power is not two independent 100 W builds. Each path is rated 20 V at 5 A, and the package shares one thermal pad per function, so simultaneous full load on both ports pushes the die temperature rather than the rail voltage. Cable compensation and current monitoring are per port, but the thermal budget is common.

The controller supply and the power path have different limits. VIN_3V3 is a narrow 3.135 V to 3.45 V rail, while the paths run to 22 V. Feeding VIN_3V3 from a 5 V housekeeping rail without a regulator will destroy the part, and the dead battery LDO is there to remove that dependency, not to replace the rail.

The 13 GPIOs and the two I2C ports are the integration budget. Alternate mode mux control, retimer enable, fan control and LED status all have to fit inside that count, and the second I2C port is primary only, which limits how the embedded controller and the PD controller can share a bus. Pin planning happens before the board is routed, and a late mux addition can force a board spin.

The firmware image is part of the order code. The D block selects the firmware and the alternate modes the controller supports, and the same die with a different image behaves differently on the bus. When a customer reports that a dock negotiates one monitor but not another, the first question is which image the controller carries, not which cable was used.

Certification can be reused, but only within limits. The part carries USB PD 3.0 and Type-C certification and an IEC 62368-1 certificate, which shortens a product's own approval, and the certificate applies to the controller rather than to the whole product. The enclosure, the connector and the power path still have to be assessed as a system.

A part marked NRND still needs a plan. The usual route is to put the current generation device into the next board while keeping this one for service and for builds that are already qualified. That means holding stock against the forecast rather than buying on demand, and it means asking the vendor for a lifecycle statement in writing rather than reading the status column alone.

Where this order code fits

The part serves notebooks, docking stations, monitors with power delivery, industrial terminals and multi port chargers where two Type-C receptacles have to negotiate power in both directions without external hot swap FETs. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Why is this part marked NRND? The vendor moved its dual port PD line to a newer controller generation. The part remains orderable in the channel and is right for repair and legacy builds, but a new platform should start from the current device, and we say so on the quote.

Does it support 100 W per port? Each path is rated 20 V at 5 A, so 100 W per port is inside the switch rating. The package thermal pad, the copper it sits on and the ambient decide whether both ports can do that at the same time.

Can it run without a battery? Yes, the internal 3.3 V LDO provides dead battery support, so a flat pack still negotiates a charge contract when the device is plugged in.

Does the controller need external FETs for the power path? No for the 5 V to 20 V, 5 A paths, which are on the die. External protection is still normal for VBUS surge and for the connector's own ESD requirement.

Can both ports charge at once? The policy engine supports dual port operation. The thermal pad and the enclosure decide how much power both ports can pass at the same time.

Can you supply the newer replacement? Yes, on request. We will name the current generation device and the differences that matter for a qualified build rather than presenting it as a direct swap.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.