Contact Us

TPS7A4901DGNR

Brand: Texas Instruments
Texas Instruments TPS7A4901DGNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A4901DGNR — Power Management & Signal Chain | Superb Automation

TPS7A4901DGNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A4901DGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A4901DGNR: 36 V, 150 mA ultralow noise regulator with a wide adjustable output

TPS7A4901DGNR is a 36 V input, 150 mA low dropout regulator with a resistor set output and very low output noise in a HVSSOP (DGK) body of 8 pins. The output is adjustable from 1.194 V to 33 V with an external divider, the noise is 15.4 microvolts RMS from 10 Hz to 100 kHz, and a capacitor on the NR pin trades noise against start up time.

Order code and package

Order code read outTPS7A4901 DGK R: family, DGK 8 pin HVSSOP with PowerPAD, R tape and reel
PackageHVSSOP PowerPAD, 8 pins, 3.00 mm by 3.00 mm, exposed pad for heat
Other bodyVSON, 8 pins, 3.00 mm by 3.00 mm, same silicon
Carrierlarge tape and reel
Operating temperatureminus 40 to plus 125 degrees Celsius
Output capacitorstable with 2.2 microfarad ceramic, which keeps the solution small
Soft startcapacitor programmable on the NR pin, which also sets the noise filter corner

Electrical parameters that decide the application

Input voltage3 V to 36 V
Output voltage1.194 V to 33 V adjustable with two resistors
Output current150 mA
Dropout260 mV typical at 100 mA, 600 mV maximum at 150 mA over the full temperature range
Output noise15.4 microvolts RMS from 10 Hz to 100 kHz, 12.7 microvolts RMS from 20 Hz to 20 kHz
Ripple rejection72 dB at 120 Hz, better than 52 dB from 10 Hz to 400 kHz
Reference1.194 V, which is the floor of the adjustable range
Protectioncurrent limit and thermal shutdown, both internal
EnableCMOS logic level, active high
Minimum output1.194 V, the reference voltage, so a divider is always needed
Reference bypassthe NR pin capacitor filters the reference and sets the ramp at the same time

Family variants and how they differ

TPS7A4901the adjustable version on this page, 1.194 V to 33 V
Fixed siblingsthe same family is offered in fixed output versions for boards that do not need a divider
Negative railsthe matching negative regulator is a separate device, this family is positive only
Body choiceHVSSOP and VSON are the same die, the PowerPAD in the HVSSOP is what makes 150 mA comfortable
Noise optionthe NR capacitor is the only noise knob, and it also slows the ramp

Points to check before this part goes on a BOM

The divider sets both the output and the error. With a 1.194 V reference, a 33 V output needs a divider ratio near 27:1, and 1 percent resistors contribute 1 percent of output error on their own before the regulator's own accuracy is counted. For a 30 V rail that is 300 mV, which is larger than most loads tolerate, so 0.1 percent resistors belong in the bill of materials.

The 600 mV maximum dropout at 150 mA is the number that limits a 33 V output. Holding 33 V requires an input of at least 33.6 V, and a 36 V rail at minus 5 percent is 34.2 V, which leaves 600 mV. That is exactly the limit, so a 33 V rail on a nominal 36 V supply has no margin at all and the build should target 30 V or accept a lower current.

The noise figure assumes the NR capacitor. The 15.4 microvolt RMS number is measured with the reference bypass in place, and removing that capacitor to speed up the ramp gives a noisier rail. The same capacitor sets the start up time, so noise and ramp time are one decision, not two.

150 mA in an 8 pin body is a thermal question above a few volts of differential. Dropping 24 V to 5 V at 150 mA is 2.85 W, which the PowerPAD can pass into copper but not into still air inside a sealed box. The current rating is honest and the differential is the constraint, so a 24 V to 5 V rail at 150 mA usually wants a switcher in front.

The two bodies share a die but not a thermal path. The VSON has a smaller exposed pad than the HVSSOP PowerPAD, and at 150 mA with a large differential the difference shows up as a lower shutdown temperature in practice. A board that swaps bodies for supply reasons should recheck the copper under the part.

The reference is the noise floor of the whole regulator. A 1.194 V reference with the NR pin bypassed gives the 15.4 microvolt figure, and a board that leaves the pin open gets more noise and a faster ramp. The capacitor is small, and its value is one of the few places where a change is audible in an audio rail and visible on a phase noise plot.

A 33 V output on a 36 V supply is a test of patience. The pass element has 600 mV at 150 mA, the divider has to be 0.1 percent to keep the error inside a useful band, and the dissipation at that differential is small but the margin against the input tolerance is gone. Most industrial builds settle at 30 V and keep the rest as headroom.

The divider current is part of the quiescent budget. A 33 V output with a 100 kiloohm top resistor draws about 300 microamps from the rail, which is far more than the regulator's own quiescent current and can matter in a battery instrument. Larger resistors reduce it and add error from the feedback pin bias current, so the value is a trade rather than a default.

Soft start and noise share the NR pin. The capacitor slows the ramp and filters the reference at the same time, so a fast start up and a quiet rail pull in opposite directions. In an instrumentation front end the quiet rail usually wins, and the start up time is absorbed by the sequencing of the rest of the board. A 150 mA rail with a large NR capacitor can take tens of milliseconds to arrive, which is worth knowing before a firmware timeout is set.

Where this order code fits

The part serves instrumentation front ends, ADC references, low phase noise oscillator supplies, medical sensor rails and audio circuits that run from a 12 V or 24 V bus and cannot tolerate switching residue on the analogue rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the RF Component Sourcing page.

Questions buyers ask

What is the highest output I can set? 33 V, and only if the input stays at least 600 mV above it at full load. On a nominal 36 V rail that is tight, so most builds stop at 30 V.

Does the output noise depend on the output voltage? Yes in practice. Noise and rejection are specified at a stated operating point, and a rail close to the input has less loop gain and therefore more noise and less rejection.

Can it supply a 200 mA load? No. The rating is 150 mA, and the current limit sits above that. A 200 mA load will drop the rail rather than trip cleanly, which is harder to diagnose.

What sets the minimum input voltage? The output plus the dropout. For a 5 V output the input has to stay above 5.6 V at 150 mA over temperature, so a 6 V rail is workable and a 5.5 V rail is not.

How long does the output take to come up? It follows the NR pin capacitor. A larger capacitor gives a slower, quieter ramp, and the exact time is read from the vendor's start up curve for that value.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.