Contact Us

UCC27523DR

Brand: Texas Instruments
Texas Instruments UCC27523DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27523DR — Power Management & Signal Chain | Superb Automation

UCC27523DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27523DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27523DR: dual channel 5 A low side gate driver with independent enables

UCC27523DR is a two channel low side driver that puts two 5 A outputs with matched timing into one eight pin body in a SOIC (D) body of 8 pins. Each channel sources and sinks 5 A from a 4.5 V to 18 V supply, with 13 ns typical propagation delay and 1 ns of matching between the channels. The matching is what allows the two outputs to drive parallel switches or a synchronous rectifier pair without a skew problem.

Order code and package

Order code read outUCC27523 D R: device UCC27523, D eight pin SOIC, R large tape and reel
PackageSOIC (D), 8 pins, the industry standard dual driver pin out
Carrier in the vendor addendumUCC27523DR at 2500 pieces on a large reel, with 75 piece tube rows for the same body
Moisture levelLevel 1, 260 degrees unlimited floor life
Lead finishNickel palladium gold, with a palladium gold variant on some rows
Part marking27523
Operating temperatureminus 40 to plus 140 degrees, junction and ambient

Electrical parameters that decide the application

Supply range4.5 V to 18 V, single supply, outputs held low during undervoltage lockout
Peak drive current5 A source and 5 A sink per channel into 0.22 uF at 1 kHz
Continuous output current0.3 A DC per channel
Propagation delay13 ns typical, with 1 ns of delay matching between channel A and channel B
Rise and fall time7 ns and 6 ns typical, slightly faster than the single channel family
Undervoltage lockout4.20 V typical start, 3.90 V minimum after start, 0.3 V hysteresis
Input thresholds2.1 V high and 1.2 V low nominal, fixed and independent of the supply, 0.9 V of hysteresis
Enable thresholds2.1 V high and 1.15 V low per channel, separately pinned, with 0.95 V of hysteresis
Start up current75 uA with both inputs high, 25 uA with both low, at a 3.4 V supply
Output pull upInternal pull up resistance sets the high level close to the supply, with 75 mV maximum low level at 10 mA
Absolute maximum20 V on the supply, 5 A pulsed output for 0.5 ms, 150 degrees junction
Parallel operationThe two outputs may be tied for double the drive current, or driven from one input for two parallel switches

Family members and how they differ

UCC27523dual, both channels non-inverting, independent enables, the part on this page
UCC27525the same drive with one inverting and one non-inverting channel
UCC27526the same drive with both channels inverting
SOIC and HVSSOP bodiesthe same die in the eight pin SOIC and in the eight pin HVSSOP with a thermal pad, at 2500 pieces per reel for both
Against the single channel parttwo UCC27517 devices give the same drive without the 1 ns matching, in twice the board area

Points to check before this part goes on a BOM

The 1 ns delay matching is the reason to buy a dual rather than two singles. In a synchronous rectifier or a parallel switch pair, a few nanoseconds of skew turns into a few tens of amps of imbalance during the switching transition, and that imbalance is what heats one device more than its neighbour. The matching is specified as typical, so a worst case timing budget should still leave margin between the channels.

Both channels have their own enable pin, and each enable has about 0.95 V of hysteresis. That allows a controller to shut one channel down while the other keeps running, which is useful when a bridge has to be parked or when a fault in one half needs to be isolated. Enabling is not instantaneous: the enable path adds its own delay, and a channel that is enabled into a charged switch node may briefly conduct in the wrong direction.

The 5 A rating is a peak into a capacitive load, and the continuous limit of 0.3 A per channel is the thermal boundary. At 200 kHz with 200 nC of total gate charge the driver delivers 40 mA per channel, which is well inside the limit, but two channels at 1 MHz with large dies add up, and the eight pin SOIC has limited copper to dissipate the result. A thermally demanding build uses the HVSSOP body with the exposed pad rather than the plain SOIC.

Tying the two outputs in parallel doubles the drive current but not the timing precision. The two channels are matched to 1 ns typical, and in parallel that skew is a small fraction of the total transition, so the arrangement is common for a very large single switch. What it does not do is increase the 0.3 A continuous limit, which is set by the package rather than by the die.

The pin out follows the industry standard for dual low side drivers, which is why this part appears as a second source for older driver families. When a board is being re-qualified, the input polarity has to be confirmed against the original part: the 23 is non-inverting on both channels, the 25 and 26 are not, and dropping the wrong member into a socket inverts the drive.

Where this order code fits

Applied in synchronous rectification, half and full bridge primaries, motor drive inverters, class D audio output stages and any two switch topology that needs two fast, matched low side drivers from a single supply. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

Can the two channels drive one large MOSFET together? Yes, the outputs may be tied in parallel for more peak current, and the 1 ns matching keeps the transition clean. The 0.3 A continuous limit still applies, so the arrangement suits a large gate charge at moderate frequency.

What replaces a UCC27524? The 24 is the same dual non-inverting arrangement in a different family. Before offering it as a substitute, the enable polarity, the UVLO level and the propagation delay have to be compared row by row, because the pin out is not always identical.

Are the enables active high? Yes on this member, with 2.1 V high and 1.15 V low thresholds and 0.95 V of hysteresis. A floating enable is not defined, so both enable pins should be tied to a known level.

How does it behave at power up? Both outputs are held low while the supply is below the undervoltage lockout, so a MOSFET driven by this part cannot be turned partially on during a slow rail rise.

Which package handles heat better? The eight pin HVSSOP with the exposed thermal pad. It carries the same die and the same 2500 piece reel, and it is the right choice when both channels run at high frequency into large gates.

Do both channels need the same supply decoupling? Yes, and each channel should have its own capacitor close to the pin. Sharing one capacitor between two 5 A outputs puts the transient current of both channels through the same trace, which raises the supply bounce during a simultaneous transition.

What is the quiescent current with one channel disabled? The disabled channel stops drawing gate charge current but the bias remains, so the supply current falls by roughly the gate charge contribution of that channel rather than to zero. The enable path itself draws almost nothing.

Is there a lower current member of the same family? Yes, the family is published in several current classes with the same pin out. A smaller die reduces the gate drive current and the cost where a 5 A pulse is more than the switch needs.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.