Contact Us

INA186A1IYFDR

Brand: Texas Instruments
Texas Instruments INA186A1IYFDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA186A1IYFDR — Power Management & Signal Chain | Superb Automation

INA186A1IYFDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA186A1IYFDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA186A1IYFDR: a 25 V/V current sense amplifier in a six ball body

INA186A1IYFDR is the 25 V/V member of the INA186 current sense family in the six ball DSBGA on a 3000 piece large reel. It measures shunt drops at a common mode from 0.2 volts below ground to 40 volts above it while running from as little as 1.7 volts, draws 48 microamps typical, and carries 120 dB of rejection with 50 microvolts of maximum offset.

The body is the part of this code that has to be read before it is bought. The DSBGA brings the enable pin out and ties the reference node to ground inside the package, so the output sits near zero with no current and rises from there: it is a one direction monitor. Everything else is the family's, including the 1 per cent gain error and the 0.3 volts per microsecond slew rate.

INA186A1IYFDR as the vendor document publishes it

Gain25 V/V fixed
Gain error0.04 per cent typical, 1 per cent maximum
Gain error drift2 ppm per degree typical, 10 maximum
Nonlinearity0.01 per cent typical of full scale
Offset voltage3 microvolts typical, 50 microvolts maximum, referred to the input
Offset drift0.05 microvolts per degree typical, 0.5 maximum
Input bias current0.5 nanoamps typical, 3 nanoamps maximum
Input offset current70 picoamps typical
Common mode rejection120 dB minimum, 150 typical, measured over minus 40 to plus 125 degrees
Power supply rejection1 microvolt per volt typical, 10 maximum
Reference rejection0.01 per cent typical, 10 microvolts per volt maximum
Common mode rangeminus 0.2 volts to plus 40 volts, independent of the supply
Supply range1.7 volts to 5.5 volts
Quiescent current48 microamps typical, 65 maximum, 90 over temperature
Shutdown current10 nanoamps typical, 100 maximum
Bandwidth45 kHz at 25 V/V, 37 kHz at 100 V/V, 35 kHz at 500 V/V, intermediate options between those
Slew rate0.3 volts per microsecond
Settling to 1 per cent30 microseconds from a current step
Voltage noise75 nanovolts per root hertz
Swing to the positive rail20 millivolts typical, 40 maximum into 10 kohm
Swing to ground0.05 millivolts typical, 1 maximum
Zero current output2 millivolts typical, 10 maximum with the reference grounded
Stable load capacitance1 nanofarad
Temperature rangeminus 40 to plus 125 degrees
Vendor statusactive, 3000 piece large reel
Catalogue codeINA186A1IYFDR
Vendor stringINA186A1IYFDR
BodyDSBGA, YFD, six ball, 1.17 by 0.765 millimetres
Moisture levellevel 1, 260 degrees, no floor life limit
Directionone direction, no reference pin

Minus 0.2 to plus 40 volts of common mode on a 1.7 volt supply

The input of INA186A1IYFDR is specified from 0.2 volts below ground to 40 volts above it, and the window is independent of the supply. A 3.3 volt rail can therefore measure a 40 volt bus, and the negative end matters on a low side shunt where the ground return lifts by a diode drop or by the voltage across a trace.

Inside the window the rejection is 120 dB minimum and 150 typical, measured with no differential signal across the inputs. Outside it the part does not stop working, it stops being specified, and the current through the input protection becomes the error. That is why a bus that can ring above 40 volts needs a series resistor on both inputs rather than a larger shunt, and why the 40 volt figure belongs in the requirements rather than in the notes.

Fifty microvolts of offset and half a nanoamp of bias

Offset on INA186A1IYFDR is 3 microvolts typical and 50 microvolts maximum referred to the input, with 0.05 and 0.5 microvolts per degree of drift, and the bias current is 0.5 nanoamps typical and 3 nanoamps maximum with an offset current of 70 picoamps. The zero drift architecture is what keeps the drift row small enough to ignore across minus 40 to plus 125 degrees.

The bias row decides whether microamp measurement is possible at all. Three nanoamps flowing in a 1 ohm shunt is 3 nanovolts, which is nothing, and in a 1 megohm path it is 3 millivolts, which is everything. A large shunt is allowed by the low bias, and a large shunt is what turns a microamp current into a signal the converter can resolve: 100 microamps in 1 ohm is 100 microvolts, which at 200 V/V is 20 millivolts, a real code on any converter.

Which body carries the reference pin and which carries the enable pin

INA186A1IYFDR is offered in three bodies and they are not interchangeable on function. The SC70 holds the reference pin and no enable. The SOT-23 thin body holds both. The DSBGA holds the enable and ties the reference node to ground inside the package, which makes it a one direction part.

The last point is the one to catch before a board is released, because the difference does not appear in an electrical table that is quoted at a mid rail reference. A channel that has to read current in both directions needs the reference pin to lift the output at zero current, and a DSBGA cannot do it. The gate runs the other way: a channel that has to be powered down between readings needs the enable pin, and the SC70 does not have one. Choose the body from those two functions first and from the footprint second, since all three are small enough that the footprint is rarely the reason.

Five fixed gains from 25 to 500 in one body

INA186A1IYFDR is one gain option of a family that shares a die, a pinout and a 1.7 to 5.5 volt supply. A1 is 25 V/V, A2 is 50, A3 is 100, A4 is 200 and A5 is 500, and the letter is the only thing that changes between the five order codes in the same body.

The option is chosen from the shunt and the converter rather than from a preference. A 10 milliohm shunt carrying 2 amps develops 20 millivolts, which at 25 V/V is 500 millivolts and at 200 V/V is 4 volts, so one shunt fills the useful range of a 3.3 volt converter at one gain and clips it at another. Because the gain error is 1 per cent maximum at every option, the gain buys scale and not accuracy, and the option that puts the working current nearest the top of the converter's span is the one to order.

Where a zero drift shunt monitor earns its place

INA186A1IYFDR suits four kinds of channel: a battery instrument that sleeps between readings and has to wake with the same offset it had before, a charger whose current loop closes through the monitor, a server or baseband supply where a 40 volt bus has to be measured from a 3.3 volt rail, and a test fixture that measures microamps through a large shunt.

It stops at three things. The output is a fixed gain, so a channel whose current range spans more than one converter decade needs a different gain option or a second path. The input window stops at 40 volts, which rules out a 48 volt telecom bus without a divider that then carries its own error. And the part is a shunt monitor rather than an isolated one, so a high side measurement on a mains referenced rail needs an isolator behind it. Our amplifier cross reference page lists the members of the family side by side, and the drop in replacement check page covers the rows to compare before one gain option is written in place of another.

One hundred and twenty decibels of rejection against a fixed noise floor

The rejection of INA186A1IYFDR is 120 dB minimum, so a 1 volt swing on a 40 volt common mode becomes 1 microvolt at the input. The voltage noise density is 75 nanovolts per root hertz, so a 10 kHz bandwidth carries 7.5 microvolts of noise and a 1 kHz bandwidth carries 2.4 microvolts.

Read together, the two rows say that rejection is worth exactly what the bandwidth allows. A channel filtered to 1 kHz sees 2.4 microvolts of noise and 1 microvolt of rejection error, and neither dominates. A channel that runs the full 45 kHz at the A1 gain sees 16 microvolts of noise, and the rejection error disappears into it. The practical conclusion is to filter between the amplifier and the converter rather than to look for more rejection, and to compute the noise on the bandwidth that actually reaches the converter rather than on the small signal figure.

A one direction part on a ball array is a commitment, so the channel's direction belongs in the requirements before the reel is bought. Our BOM scrubbing page covers the body and gain check against the bill of materials, and the traceability report page covers what travels with a ball array that has no readable marking.

Can this body measure a charging current? Not in both directions. The reference node is grounded inside the package, so the output cannot be offset at zero current and the part only reports current flowing one way.

Is 25 V/V enough for a 10 milliohm shunt? It gives 250 millivolts at 10 amps, which is a usable span on a 3.3 volt converter but leaves most of the range unused; a 10 milliohm shunt at 2 amps needs the 200 or 500 V/V option instead.