Contact Us

INA157UA

Brand: Texas Instruments
Texas Instruments INA157UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA157UA — Power Management & Signal Chain | Superb Automation

INA157UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA157UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA157UA: the wider grade of the 4 MHz difference amplifier, in rails

INA157UA is the same 4 MHz difference amplifier in the wider grade, supplied in rails. Offset is 1000 microvolts maximum at the output instead of 500, and the drift row moves from 2 microvolts per degree typical and 5 maximum to 20 and 60, which is the larger of the two changes: over a 45 degree swing the UA grade drifts 900 microvolts where the U grade drifts 90.

That makes the grade decision a temperature decision rather than a bench decision. On a bench at 25 degrees both parts trim to the same place and the difference is invisible; in an enclosure that runs 20 degrees above ambient the UA grade's drift is 0.009 per cent of a plus or minus 10 volt span per 45 degrees, which is inside a 12 bit budget and outside a 16 bit one. The network, the bandwidth and the supply window are identical on both grades.

INA157UA as the vendor document publishes it

Gain0.5 V/V in the half gain connection, 2 V/V with sense and reference exchanged
Gain error0.01 per cent typical, 0.1 maximum on the UA grade
Gain drift1 ppm per degree typical, 10 maximum
Nonlinearity0.0002 per cent typical, 0.002 maximum of full scale
Offset200 microvolts typical, 1000 maximum referred to the output
Offset drift20 microvolts per degree typical, 60 maximum
Supply rejection0.25 microvolts per volt typical, 10 maximum
Input impedance24 kohm differential, 18 kohm common mode
Common mode rejection80 dB minimum, 96 typical
Voltage noise1.3 microvolts peak to peak, 26 nanovolts per root hertz at 1 kHz
Bandwidth4 MHz small signal at a gain of one half
Slew rate14 volts per microsecond
Settling to 0.01 per cent3 microseconds on a 10 V step
Overload recovery3 microseconds from a 50 per cent overdrive
Output swingwithin 2 volts of each rail into 2 kohm
Output current60 milliamps continuous into the common point
Quiescent current2.4 milliamps typical, 2.9 maximum
Supply rangeplus or minus 4 to plus or minus 18 volts
Stable load capacitance500 picofarads
Bodyeight pin SOIC, marking INA157UA
Temperature rangeminus 40 to plus 85 degrees
Catalogue codeINA157UA
Vendor stringINA157UA
Carrierrails
GradeUA, 1000 microvolts maximum offset

Five hundred microvolts at the output, 2 microvolts per degree

Offset on INA157UA is specified at the output, not at the input, because the network refers it there: 100 microvolts typical and 500 maximum on the U grade, 1000 maximum on the UA, with 2 microvolts per degree typical and 5 maximum of drift on the U grade and 20 and 60 on the UA. Supply rejection is 0.25 microvolts per volt typical and 10 maximum over the full supply range, and the noise is 1.3 microvolts peak to peak from 0.1 to 10 Hz and 26 nanovolts per root hertz at 1 kHz.

Referred to the output makes the budget simpler than it looks. Five hundred microvolts on a plus or minus 10 volt output span is 0.0025 per cent of full scale, a sixtieth of what a 16 bit converter resolves, and 2 microvolts per degree over a 45 degree swing is 90 microvolts, a fifth of the initial offset. The UA grade at 1000 microvolts and up to 60 microvolts per degree is a different proposition: the drift alone is 2.7 millivolts over the same swing, which is 0.0135 per cent of full scale and has to be calibrated rather than ignored.

A gain of one half or two from a 12 kohm and 6 kohm network

INA157UA is a difference amplifier built from a precision op amp and a laser trimmed network of 12 kohm and 6 kohm resistors. In the connection the vendor calls G equal to 1/2 the input pair drives the 12 kohm arms and the output is half the differential input; exchanging the sense and reference connections gives a gain of 2 from the same network. The ratio, not the absolute value, is trimmed, and the vendor states the absolute value carries a 20 per cent spread, which is why the input impedance is 24 kohm differential rather than a round number.

Both connections are useful and they are different circuits. Half gain attenuates a plus or minus 20 volt differential signal into the window of a plus or minus 10 volt converter and keeps the common mode rejected on the way in. Gain of 2 turns a 5 volt shunt drop into 10 volts for the same converter. The 0.01 per cent typical gain error and the 1 ppm per degree ratio tracking belong to both, because they are properties of the network rather than of the connection.

Line receiver, ground loop breaker and shunt monitor

INA157UA covers three jobs that look unrelated and are the same circuit. As a differential line receiver it takes a signal that has travelled on a twisted pair and rejects what the pair picked up on the way. As a ground loop breaker it converts a differential voltage between two grounds into a single ended output referred to one of them, with 86 dB minimum and 96 typical of rejection doing the work. As a current shunt monitor it measures the drop across a resistor in a supply line whose common mode sits well above or below the amplifier's own supply.

In all three the value is the trimmed network and the common mode window, and in all three the limits are the same. The input impedance of 24 kohm loads the source, so a 1 kohm source loses 4 per cent of the signal and any mismatch between the two source resistances turns common mode into a differential error. The supply floor of plus or minus 4 volts rules out a 5 volt single supply channel. And the 4 MHz bandwidth is small signal, so a 10 volt step takes 0.7 microseconds of ramp before settling begins.

Plus or minus 4 to 18 volts, and a window that passes the rails

The supply window of INA157UA is plus or minus 4 to plus or minus 18 volts, rated at plus or minus 15, and the output reaches to within 2 volts of each rail into a 2 kohm load, 1.8 typical. Quiescent current is 2.4 milliamps typical and 2.9 maximum. The common mode range is the interesting row: it extends beyond both supply rails, and the vendor specifies it as a function of the supply and the output level rather than as a fixed number.

That extension is what lets the part sit on a shunt above its own supply, and it is also what makes the row easy to misread. The window is quoted with the output at zero, so a channel that has to measure a high common mode while its output is near a rail is outside the specified condition and has to be checked against the curve. A plus or minus 15 volt supply with a common mode of plus or minus 37.5 volts is inside the window; the same common mode with the output at plus 10 volts is not, and the difference is a slow, temperature dependent error rather than a clipping event.

2.4 milliamps and 60 milliamps of output current

The quiescent current of INA157UA is 2.4 milliamps typical and 2.9 maximum, which at plus or minus 15 volts is 87 milliwatts and in the eight pin body at 150 degrees per watt is a 13 degree rise. The output can deliver 60 milliamps continuous into the common point, so the part can drive a cable or a converter's sampling network without a buffer, and it is stable into 500 picofarads, which covers a metre of screened cable before a series resistor is needed.

The 60 milliamps is a short circuit rating rather than a working current. Into a 2 kohm load at 10 volts the part delivers 5 milliamps, and that is the load the output swing and distortion figures are quoted into. A channel that has to drive 50 ohms, a video cable or a transformer primary is asking for several times the rated current and the output swing will collapse well before the limit is reached, which is what the swing against load curve in the vendor document is there to show.

Four megahertz, 14 volts per microsecond, 3 microseconds to 0.01 per cent

INA157UA carries 4 MHz of small signal bandwidth at a gain of 1/2, a slew rate of 14 volts per microsecond, 2 microseconds of settling to 0.1 per cent on a 10 volt step into 100 picofarads and 3 to 0.01 per cent, with 3 microseconds of overload recovery from a 50 per cent overdrive. The output current limit is 60 milliamps continuous into the common point and the part is stable into 500 picofarads.

Those are fast numbers for a difference amplifier and they come from the 2.4 milliamps of supply current, which is twelve times what a micropower difference amplifier draws. The trade is deliberate: a synchronous demodulator, a differential line receiver on a long cable, or a current shunt on a switching node all need the part to follow a signal that a slower amplifier would round off, and in each of those the 2.4 milliamps is small next to the rest of the channel. A battery channel that samples once a second should not pay for it.

If the channel is calibrated at 25 degrees and runs hot, the grade decision should be made on the drift row. Our drop in replacement check page lists the rows to compare, and the last time buy page covers what to do if only one grade is being withdrawn.

Is the UA grade usable as a current shunt monitor? Yes, within its common mode window and with the input impedance in mind: 24 kohm differential loads a low value shunt by a fraction of a per cent and the error moves with temperature.

Does the wider grade change the slew rate? No. 14 volts per microsecond and 4 MHz are network and amplifier properties, not grade properties.