Contact Us

INA129P

Brand: Texas Instruments
Texas Instruments INA129P is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA129P — Power Management & Signal Chain | Superb Automation

INA129P

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA129P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA129P: the plain grade eight pin plastic DIP with the 49.4 kΩ gain network

The INA129P is the plain grade of the eight pin plastic DIP in a 50 piece tube, and the reason to choose it over the INA128P is one resistor value inside the part. The INA129 uses a 49.4 kΩ gain network so that G = 1 + 49.4 kΩ divided by RG, which reproduces the gain of a competing part whose external resistor was chosen for that equation. On an existing board with a 49.4 kΩ based gain table, the INA129 is a drop in replacement and the INA128 is not.

The DIP body is 9.81 mm by 9.43 mm and it can be socketed, which makes this code the bench and calibration member of the family. The electrical rows are the family rows: 50 µV maximum offset, 0.5 µV per degree drift, 5 nA bias current, 8 nV per root hertz noise, 120 dB common mode rejection, 700 µA quiescent current and 200 kHz of bandwidth at a gain of 100.

The INA129P rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
GradePlain, the family offset and gain error rows
Gain equationG = 1 + 49.4 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum on the standard rows
Voltage noise8 nV per root hertz at 1 kHz
Common mode rejection120 dB minimum
Bandwidth1.3 MHz at a gain of 1, 200 kHz at a gain of 100
Input protectionPlus or minus 40 V without damage
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodyPDIP, P outline, 8 pins, 9.81 by 9.43 mm
Carrier50 pieces per tube
INA128 equivalentSame die with a 50 kΩ network, not gain compatible

Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ

The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.

Because of that, INA129P must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.

Current feedback input stage and bandwidth at a gain of 100

The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA129P serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.

Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129P the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

50 µV of offset and half a microvolt per degree

The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA129P can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.

The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.

120 dB of common mode rejection and the source imbalance that removes it

The common mode rejection row is 120 dB minimum on the family, measured with a 1 kΩ source imbalance, and it is the number that decides whether a bridge channel can reject a 50 Hz disturbance. Rejection degrades with source imbalance at roughly 1 dB per 100 Ω above the test condition, so a channel with a 10 kΩ mismatch between the two input legs has thrown away most of the 120 dB. In practice that mismatch comes from the sensor rather than from the board: a 350 Ω bridge with one leg 5 Ω high, or a thermocouple with a 2 kΩ cable resistance on one side only.

The fix is a pair of matched resistors at the input, or a buffer for each leg, or a sensor with a trimmed output impedance. The REF pin is part of the same problem: the vendor notes that 8 Ω in series with REF is enough to degrade rejection on a typical part, so the reference has to be driven from a low impedance source such as an amplifier or a shunt reference with a capacitor, not from a divider alone. On INA129P the rejection also falls with frequency, and the vendor curve of rejection against frequency is the one to read for a switching supply disturbance rather than the dc row.

Plus or minus 40 V of input protection and the bias current return path

The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.

The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA129P is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.

Buying INA129P

The purchase decision is almost always a continuation decision: this code is bought because an existing board was built around the 49.4 kΩ gain equation, and the alternative is a resistor change on every channel. Buying the plain grade is correct when the channel has a trim or the full scale is large; the A grade exists for the small full scale case and differs only in the offset window.

Fifty pieces in a tube is a prototype quantity and 75 to 100 pieces of a DIP is a year of service stock for a calibration fixture. Because the DIP is the code least likely to be held by a distributor, a programme that expects to run for a decade should hold a buffer rather than order against demand. Our last time buy page covers how that buffer is sized, and the pin to pin cross reference page covers the compatible codes.

Questions that arrive with this part number

Whether the INA129 and the INA128 are interchangeable is the first question and the answer is no on a calibrated channel: the gain differs by 1.2 per cent at a gain of 100 and 0.12 per cent at a gain of 10, which passes a functional test and fails a calibration. The second is whether the P and U codes are interchangeable, and they are electrically, with the body and the footprint as the only difference.

The third is about the gain resistor value table. A board built for the 49.4 kΩ equation should keep its resistor values when it moves to this code, and a board built for the 50 kΩ equation must not, which is why the gain equation belongs on the drawing as well as in the vendor document.