INA129MDREP
Product Specifications
INA129MDREP
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA129MDREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA129MDREP: a special order string that the addendum does not list
The INA129MDREP is a catalogue string that the current vendor addendum does not print. The addendum lists INA129P, INA129PA, INA129U, INA129U/2K5 and the G4 variants of those, and there is no MDREP row. The letters decode as an M prefix, a D body and a REP suffix, which is the shape of a special or enhanced product code rather than a catalogue part, and the honest position is that the string has to be confirmed with the vendor or against a label before it is quoted.
What is certain is the device family. The INA129 is a three op amp instrumentation amplifier identical to the INA128 except for the internal gain network: it uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG, which makes it a drop in replacement for a competing part whose gain resistor was chosen for that equation. The rest of the rows are the family rows: 50 µV maximum offset, 0.5 µV per degree drift, 5 nA bias current, 700 µA quiescent current, 120 dB common mode rejection and 200 kHz at a gain of 100.
The INA129MDREP rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback |
| Vendor status | Code not listed in the current addendum |
| Data sheet | SBOS051G, revised January 2026, shared with the INA128 |
| Addendum rows for this family | INA129P, INA129PA, INA129U, INA129U/2K5 and the G4 variants |
| Body implied by the string | D outline, the SOIC body, 8 pins |
| Gain equation | G = 1 + 49.4 kΩ divided by RG |
| Gain range | 1 to 10,000 V/V |
| Input offset voltage | 50 µV maximum on the family row |
| Offset drift | 0.5 µV per degree maximum |
| Input bias current | 5 nA maximum on the standard rows |
| Common mode rejection | 120 dB minimum |
| Bandwidth | 1.3 MHz at a gain of 1, 200 kHz at a gain of 100 |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Temperature range | Minus 40 to plus 85 degrees |
| Catalogue sibling | INA129U and INA129UA in the same body |
Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ
The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.
Because of that, INA129MDREP must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.
Current feedback input stage and bandwidth at a gain of 100
The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA129MDREP serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.
Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.
50 µV of offset and half a microvolt per degree
The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA129MDREP can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.
The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.
The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm
The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.
The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129MDREP the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.
Plus or minus 40 V of input protection and the bias current return path
The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.
The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA129MDREP is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.
5 nA of bias current, and the 0.7 nA special order rows
The standard rows of INA129MDREP carry a 5 nA maximum input bias current, and the data sheet also prints a second set of rows for parts built from a different chip site origin with 0.7 nA maximum. That second set is not a different part number on the shelf: it is a special order condition, and the distinction matters because a customer who needs the lower bias current has to say so rather than order the base code and hope. On a 1 MΩ source the difference between 5 nA and 0.7 nA is 4.3 mV of offset, which is the difference between a channel that works and one that needs a FET input amplifier instead.
For ordinary bridge and shunt work the 5 nA row is irrelevant. A 350 Ω bridge sees 1.75 µV from it, and a 10 mΩ shunt with a 100 Ω filter sees half a microvolt. Bias current becomes the governing error above roughly 100 kΩ of source resistance, and above a megohm it is the only error worth discussing. The offset current rows are about a tenth of the bias current, so a matched source removes most of it and an unmatched source does not.
Buying a special order string before it is confirmed
The first deliverable is not a price, it is the vendor's confirmation that the string exists and what its status is. A special or enhanced product code can be active on a controlled basis with a minimum quantity, or it can be end of life with a residual quantity, and those two answers lead to completely different purchasing decisions. Asking for the date code, the marking and the available quantity at the same time saves a round trip.
If the string cannot be confirmed, the catalogue INA129U is the fallback and it is the same die with the same gain equation. Whether it meets the original requirement depends on what the REP suffix adds, and that has to come from the vendor document rather than from a distributor description. Our obsolete part cross reference hub covers how we trace a replacement, and the last time buy page covers the buffer if the code is end of life.
Questions that arrive with this part number
Whether the part is genuine is the first question, and the answer has to be evidence rather than a description: a label, a marking and a measurement. The second is whether the INA129U is an acceptable substitute, and on the electrical rows it is, because the gain equation, the offset, the drift and the bandwidth are the same.
The third question is whether the INA128 could be used instead, and it cannot without changing the gain resistor, because the 50 kΩ and 49.4 kΩ networks differ by 1.2 per cent at a gain of 100. That is a calibration failure rather than a functional failure, and it is the reason the two codes are not interchangeable on an existing board.