INA128UA2K5
Product Specifications
INA128UA2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA128UA2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA128UA2K5: the A grade SOIC on a 2500 piece large reel
The INA128UA2K5 is the A grade SOIC body on a large reel, which is the production carrier for a channel that needs the tighter offset bin and a build rate that consumes a reel. The die and the body match the tube code, the electrical rows are the family rows, and the difference is the carrier plus the level 3 floor life that comes with it.
The part is a three op amp instrumentation amplifier with a current feedback input stage: 50 µV maximum offset on the family row and a tighter bin on this grade, 0.5 µV per degree of drift, 5 nA of bias current, 8 nV per root hertz of noise, 120 dB of common mode rejection, 700 µA of quiescent current, and a gain range from 1 to 10,000 with one resistor. On a hot channel the drift row, not the offset bin, is what limits the accuracy, so the grade does not buy temperature performance.
The INA128UA2K5 rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback |
| Vendor status | Active, production |
| Data sheet | SBOS051G, revised January 2026 |
| Grade | A suffix, tighter offset and gain error window |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Input offset voltage | Family row 50 µV maximum, tighter on the A bin |
| Offset drift | 0.5 µV per degree maximum |
| Input bias current | 5 nA maximum |
| Voltage noise | 8 nV per root hertz at 1 kHz, 0.2 µV peak to peak from 0.1 to 10 Hz |
| Common mode rejection | 120 dB minimum |
| Bandwidth | 1.3 MHz at a gain of 1, 200 kHz at a gain of 100 |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Body | SOIC, D outline, 8 pins |
| Carrier | 2500 pieces on a large reel |
| Moisture level | Level 2 or level 3 depending on the addendum row, checked on the label |
| Temperature range | Minus 40 to plus 85 degrees |
| Tube sibling | INA128UA, 75 pieces per tube |
700 µA of quiescent current across a plus or minus 2.25 V to 18 V window
INA128UA2K5 draws 700 µA typical, which is four times the current of the micropower INA126 and a twentieth of what a fully featured instrumentation amplifier usually costs. The supply window of plus or minus 2.25 V to plus or minus 18 V covers a plus or minus 15 V industrial rack and a plus or minus 2.5 V single cell analogue front end in the same part number, and the common mode range tracks the rails rather than sitting at a fixed offset from ground.
The current is flat with load and nearly flat with temperature, so the supply budget can be set from the data sheet row rather than measured. What is not in the row is the reference divider and the load current. A plus or minus 15 V part driving a 10 kΩ load at 10 V adds a milliamp, which is more than the amplifier, and a single supply channel with an unbuffered mid rail divider can add a quarter of a milliamp. The amplifier is therefore rarely the largest item in the budget, and the budget is still small enough that a battery instrument can afford two channels.
Gain error rows, the A grade and the 0.024 per cent window
Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.
Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA128UA2K5 the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.
Tubes, reels and two different moisture levels
The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.
The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA128UA2K5 is the code to check it against.
Current feedback input stage and bandwidth at a gain of 100
The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA128UA2K5 serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.
Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.
8 nV per root hertz of voltage noise against 0.17 pA of current noise
The voltage noise row is 8 nV per root hertz at 1 kHz and the current noise is 0.17 pA per root hertz on the standard rows, which places the crossover source resistance at about 47 kΩ. Below that the voltage noise dominates and the amplifier is as quiet as the source; above it the current noise dominates and a FET input part would be quieter. On a 350 Ω bridge the voltage noise is the whole story and 8 nV per root hertz over a 10 Hz bandwidth is 25 nV, which against a 10 mV full scale is 2.5 parts per million.
The 0.1 to 10 Hz noise is quoted as 0.2 µV peak to peak, which is the figure that matters for a slow channel: a 10 mV full scale signal with 0.2 µV of low frequency noise has a resolution floor of 20 parts per million, better than most 16 bit converters can use. A channel that needs more resolution than that is limited by the sensor, and the amplifier stops being the item to change. On INA128UA2K5 the noise is flat enough that a higher gain does not improve the input referred figure below the crossover.
Plus or minus 40 V of input protection and the bias current return path
The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.
The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA128UA2K5 is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.
Buying INA128UA2K5
The reel and the grade are two independent decisions that are usually made together by mistake. The reel is about build rate and floor life; the grade is about the offset window on a small full scale channel. A programme that needs the grade and builds 200 boards a year should buy tubes of the A grade rather than a reel, and a programme that builds 3000 boards a year needs the reel whether the grade matters or not.
The moisture level column on this family is not uniform across the reel rows, so the label decides rather than the code. That is a five second check at receiving and it prevents a baking operation in the middle of a build. Our date code management page covers the floor life record, and the BOM shortage recovery page covers what to do when the reel is delayed.
Questions that arrive with this part number
Whether the A grade reel is the same silicon as the plain reel is the first question and it is, with the tighter bin as the only difference. The second is whether the grade can be dropped to the plain bin in a shortage, and it can if the channel has a trim or the specification has margin; the measurement that proves it is the offset at temperature, not at room temperature.
The third is the gain resistor. At a gain of 100 it is 495 Ω and at 1000 it is about 50 Ω, so a 0.1 per cent part with a 25 ppm coefficient is the right choice and the placement within a few millimetres of the pins matters as much as the tolerance. A resistor on a long trace adds inductance that shows up as peaking rather than as gain error.