Contact Us

INA128HD

Brand: Texas Instruments
Texas Instruments INA128HD is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA128HD — Power Management & Signal Chain | Superb Automation

INA128HD

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA128HD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA128HD: a code the current addendum does not print, and what to check before quoting it

The INA128HD is a catalogue string that the current vendor addendum does not print. The addendum lists INA128P, INA128PA, INA128PG4, INA128U, INA128U/2K5, INA128UA, INA128UA/2K5 and the G4 variants of those, all in the eight pin DIP and SOIC bodies, and there is no row with an H in it. The H is therefore either a legacy or distributor specific suffix, or a die sale code, and the honest position is that the string has to be confirmed against a purchase order and a label before it is quoted as an active part.

What can be stated is the device. The INA128 is a three op amp instrumentation amplifier with a 50 µV maximum offset, 0.5 µV per degree of drift, 5 nA of bias current, 700 µA of quiescent current, gain from 1 to 10,000 with one resistor using G = 1 + 50 kΩ divided by RG, and 200 kHz of bandwidth at a gain of 100 on a current feedback input stage. Those rows apply to the die, and the die is what the H code would contain if it is genuine.

The INA128HD rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback
Vendor statusCode not listed in the current addendum
Data sheetSBOS051G, revised January 2026
Addendum rows for this familyINA128P, PA, PG4, U, U/2K5, UA, UA/2K5 and their G4 variants
Body implied by the stringD outline, the SOIC body, 8 pins
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum on the standard rows
Bandwidth1.3 MHz at a gain of 1, 200 kHz at a gain of 100
Common mode rejection120 dB minimum on the family row
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
Temperature rangeMinus 40 to plus 85 degrees
Related order codesINA128U in a 75 piece tube, INA128U/2K5 on a 2500 piece reel

Current feedback input stage and bandwidth at a gain of 100

The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA128HD serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.

Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.

50 µV of offset and half a microvolt per degree

The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA128HD can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.

The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.

Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ

The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.

Because of that, INA128HD must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.

700 µA of quiescent current across a plus or minus 2.25 V to 18 V window

INA128HD draws 700 µA typical, which is four times the current of the micropower INA126 and a twentieth of what a fully featured instrumentation amplifier usually costs. The supply window of plus or minus 2.25 V to plus or minus 18 V covers a plus or minus 15 V industrial rack and a plus or minus 2.5 V single cell analogue front end in the same part number, and the common mode range tracks the rails rather than sitting at a fixed offset from ground.

The current is flat with load and nearly flat with temperature, so the supply budget can be set from the data sheet row rather than measured. What is not in the row is the reference divider and the load current. A plus or minus 15 V part driving a 10 kΩ load at 10 V adds a milliamp, which is more than the amplifier, and a single supply channel with an unbuffered mid rail divider can add a quarter of a milliamp. The amplifier is therefore rarely the largest item in the budget, and the budget is still small enough that a battery instrument can afford two channels.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA128HD the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

Plus or minus 40 V of input protection and the bias current return path

The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.

The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA128HD is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.

Buying a code that is not on the addendum

The first step is not a price, it is a status. A distributor can quote a string that the vendor no longer prints, and the parts behind that quote are either old stock, a die sale or a mislabelled reel. Asking for the date code, the marking and the reel label before an order is placed is the cheapest way to find out which. If the answer is old stock, the quantity available is the quantity that exists and the decision becomes a last time buy rather than a schedule.

The second step is the specification. If the H code is a legacy suffix on the same die, the electrical rows on this page hold; if it is a different die or a die sale, they may not, and a sample measured on the bench is the only honest answer. Our last time buy page covers how a buffer is sized when the code is end of life, and the obsolete part cross reference hub covers the alternatives.

Questions that arrive with this part number

Whether the part is genuine is the first question and the answer is that the string is not on the current addendum, so the only evidence is the label, the marking and a measurement. The second is whether the INA128U rows can be substituted, and electrically they can if the die is the same, because the offset, drift, bias current and gain equation are family rows rather than suffix rows.

The third is about the package. The D body is a 4.9 mm by 6 mm SOIC with the standard eight pin pinout, so a board drawn for the U code will take an HD part if the HD part is the same body. A board drawn for the P body will not, because the DIP footprint is a different land pattern and a different process step.