INA118P
Product Specifications
INA118P
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA118P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA118P: the low power precision amplifier in an eight pin plastic DIP
The INA118P is the plastic DIP member of the INA118 family, a three amplifier instrumentation amplifier with a laser trimmed input stage, a gain range from 1 to 10,000 on one external resistor, and a quiescent current of 350 µA. The specification reads 50 µV of maximum input offset, 0.5 µV per degree of maximum drift, 5 nA of maximum input bias current, and 110 dB of minimum common mode rejection at a gain of 1000. The inputs withstand 40 V without damage and the supply range is 2.25 V to 18 V total, which is what makes the part usable on a battery instrument.
The status on this string is the first thing a buyer needs. The plastic DIP row is last time buy in the current addendum, while the SOIC row of the same die is active. That asymmetry is common at the end of a through hole package's life and it means the through hole part is a finite supply, the surface mount part is not, and the customer with a socketed board is the one who has to plan.
The INA118P rows as the addendum publishes them
| Part class | Three amplifier instrumentation amplifier, precision, low power |
| Vendor status | LAST TIME BUY on the plastic DIP row |
| Data sheet | SBOS027C, revised September 2022 |
| Successor named by the vendor | A newer part, the INA818, is offered for new work |
| Input offset voltage | 50 µV maximum |
| Offset drift | 0.5 µV per degree maximum |
| Input bias current | 5 nA maximum |
| Common mode rejection at G = 1000 | 110 dB minimum |
| Input overvoltage protection | 40 V without damage |
| Supply range | 2.25 V to 18 V total |
| Quiescent current | 350 µA |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Gain range | 1 to 10,000 V/V |
| Body | PDIP, P outline, 8 pins |
| Carrier | 50 pieces in a tube |
| RoHS | Yes |
| Lead finish | Nickel palladium gold |
| Moisture level | Not applicable to this package type |
| Temperature range | Minus 40 to plus 85 degrees |
| Part marking | INA118P |
| Revision row | INA118P.A, production, and INA118P.B, last time buy |
| Sibling strings | INA118U and INA118UB in the SOIC body, active |
| Quantity note | 50 pieces per tube is a small carrier for a lifetime buy |
Two rows for this string sit in the addendum with different statuses, and the letter after the dot is what separates them. A buyer who searches for the plain string and finds a production row may be looking at the revision row rather than the plain one, and the two are not the same line in the vendor's system. The safest form for a purchase order is the plain string plus a written confirmation of status at the time of order.
Three hundred and fifty microamps for a battery instrument
The 350 µA of quiescent current is the number that distinguishes this family from its precision cousins, which draw several milliamps. On a four channel battery instrument the difference is 12 mA against 1.4 mA, and against a 1000 mAh cell that is nine hours against eighty. That is the entire reason this part exists next to the INA114, and it is bought for the current rather than for the accuracy.
The price is paid in noise and in drift. The 0.5 µV per degree drift is looser than the 0.3 µV per degree of the INA114, and the bias current of 5 nA is higher than the 2 nA of the INA114. A channel with a high impedance source is worse off with this part, and a channel with a low impedance bridge or shunt is not, because 5 nA into 1 kΩ is 5 µV of offset and 0.5 µV per degree into a 40 degree swing is 20 µV, both inside a 1 per cent budget on a 100 mV full scale.
Gain resistor choice at low power
The gain equation is the same 1 plus 50 kΩ over RG as the rest of the Burr-Brown precision family, so the resistor values are identical and a board can be reworked from one family to the other at the same gain. At a gain of 1000 the resistor is 50.05 Ω and the resistor tolerance dominates; at a gain of 10 it is 5.56 kΩ and a 0.1 per cent part is sufficient for a 0.1 per cent gain error.
The resistor also sets the current through the gain network, and at low power that current is part of the budget. A 50 Ω resistor at a 10 mV input carries 200 µA, which is more than half the quiescent current of the amplifier. That is not usually the limiting term, because the input signal is small, but on a high level input at a high gain the gain network current can exceed the amplifier's own supply current, and the arithmetic is worth doing before a battery life is claimed.
Forty volts of protection on a 40 V process
The input protection is specified at 40 V, which is above the 18 V maximum supply and below the 48 V of a telecom backplane. On a battery instrument the protection rarely matters; on an industrial channel sensing a 24 V loop it matters every time the loop switches. The protection steers the fault current into the supplies, so a supply that is not able to sink current will see the rail rise, and a small battery rail with a low current regulator can be pushed up by a fault rather than pulled down.
A series resistor and a clamp diode are the usual guard, and the resistor adds thermal noise of 4 nV per root Hz for every 1 kΩ, which against a 350 µA amplifier with a modest noise figure is not always negligible. The resistor value is a compromise between protection and noise, and on a low power channel the compromise usually lands at a few hundred ohms.
Last time buy planning for a socketed board
A board with a socket is a board that cannot easily move to a surface mount part, and this is the situation the last time buy exists for. The arithmetic is the remaining product build count, the annual service demand, and the cost of the alternative. A service demand of fifty parts a year for ten years is five hundred parts, which is ten tubes, and ten tubes will fit in a shoebox. That is a manageable lifetime buy, and it is much cheaper than a board revision on a mature product.
The storability question is the one that decides it. A plastic DIP in a sealed bag with a desiccant has a shelf life measured in years rather than months, and the leads do not oxidise in a dry pack. A tube left open in a workshop is a different matter, and a periodic solderability check on one part per year is the way to know where the stock stands.
Buying INA118P
The tube is 50 pieces, the status is last time buy, and the sibling in the SOIC body is active. A customer who can change the board should move to the surface mount part rather than buy a lifetime stock, and a customer who cannot should buy the stock now rather than wait for the final order window to close. The price of a last time buy part rises as the window closes, and the supply becomes a broker market after that.
The part marking is INA118P and the revision rows carry the same marking, so a tube that is labelled correctly can still contain parts from a different revision. On this family the revision letters are process records rather than performance bins, so the risk is small; on the B grade string in the same family it is not small, and the marking is the only check.
Questions that arrive with this part number
The first is whether the P can be replaced by the U. It cannot without a board change, because the body and the pin out differ. The second is whether the INA818 is a drop in replacement. It is not, and it should be evaluated on a new board rather than substituted into an existing one.
The third is whether the part can run from a 3 V battery. It runs from 2.25 V, so a 3 V rail is inside the range, and the output headroom and the reference have to be planned around the reduced swing.
For a customer facing this last time buy, our last time buy planning page sets out the arithmetic, and the pin to pin cross reference page explains what has to match before a substitute is offered.