Contact Us

DS26C31TMX-NOPB

Brand: Texas Instruments
Texas Instruments DS26C31TMX-NOPB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DS26C31TMX-NOPB — Power Management & Signal Chain | Superb Automation

DS26C31TMX-NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The DS26C31TMX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DS26C31TMX-NOPB: a quad RS-422 driver in a 16 pin outline

The DS26C31TMX-NOPB is a quad differential line driver built for balanced digital transmission, published ACTIVE on a 2500 piece reel. Four independent drivers share one enable, take TTL or CMOS levels at the input, and produce RS-422 levels at the output, so one part carries four twisted pairs or one clock and three data lines. The quiescent current is 200 µA and the active current is under 2 mA, which is CMOS territory rather than the bipolar consumption of the older 26LS31 it replaces.

Two details matter in a real backplane. The outputs are tri state, so several drivers can share a bus, and the part is specified to stop loading the line when its own supply is at zero volts, which means a powered down board does not drag down a live bus. The second is the pin out: it matches the AM26LS31 and the DS26LS31, so an existing socket accepts it without a board change.

The DS26C31TMX-NOPB rows as the addendum publishes them

Part classQuad differential line driver, RS-422
Vendor statusACTIVE, production data
Data sheetSNLS375C, June 1998, revised January 2015
Supply5 V, plus or minus 10 per cent
Input levelsTTL and CMOS compatible, 2.0 V high, 0.8 V low
Differential output into 100 Ω2.0 V minimum, 3.1 V typical
Output balance0.4 V maximum difference between the two lines
Common mode output1.8 V to 3.0 V, 0.4 V maximum offset
Output high2.5 V minimum at 20 mA sink
Output low0.3 V typical, 0.5 V maximum at 20 mA source
Quiescent supply current200 µA typical, 500 µA maximum
Active supply current0.8 mA typical, 2.0 mA maximum at 2.4 V input
Input current1 µA maximum
Tri state leakage0.5 µA typical, 5 µA maximum
Short circuit current30 to 150 mA, one output at a time
Power off leakage100 µA maximum at 6 V on the output
Propagation delay2 ns minimum, 6 ns typical, 11 ns maximum
Output skew0.5 ns typical, 2.0 ns, 3.0 ns maximum
Rise and fall time6 ns typical, 10 ns, 14 ns maximum
Enable time11 ns typical, 19 ns, 22 ns maximum
Disable time5 ns typical, 9 ns, 12 ns maximum
Input capacitance6 pF
BodySOIC, 16 pins, 9.90 by 3.91 millimetres
Tube rowDS26C31TM/NOPB, 48 pieces, tube, Active
Reel rowDS26C31TMX/NOPB, 2500 pieces, large tape and reel, Active
MarkingDS26C31TM
Temperature rangeMinus 40 to plus 85 degrees

The tube of 48 and the reel of 2500 are both live, which is unusual for a part of this age and is worth knowing: it means the vendor still supports both a service quantity and a production quantity. The military grade rows with the 883 suffix are a separate orderable set in a different document, in ceramic and flat pack bodies, and they carry a different part number rather than a different suffix on this one.

Driving a cable at 10 megabits

The 6 ns typical propagation delay and the 0.5 ns skew are what allow this part to carry a clock and its data across a backplane without eating the timing budget. At 10 megabits the bit period is 100 ns, so 6 ns of delay is 6 per cent, and the skew between two channels of the same package is under 1 per cent. That is the reason the part is still specified in telecom and instrumentation chassis that were laid out decades ago.

The output swing into 100 Ω is 2 V minimum, and the RS-422 standard requires 2 V into that load, so the part is at the edge of the specification rather than comfortably above it. A cable with heavy loss will take that margin away, which is why the standard limits the cable length to about 1200 metres at low baud and much less at 10 megabaud.

Termination, common mode and the ground question

A differential pair needs a termination resistor at the far end, and the value should match the cable, which is usually 100 to 120 Ω. The driver is specified into 100 Ω, so a 120 Ω cable termination reduces the current slightly and raises the swing, which is harmless. What is not harmless is a termination at both ends: two 100 Ω resistors in parallel load the driver with 50 Ω, and the swing drops below the 2 V minimum.

The common mode output sits between 1.8 and 3.0 V, which leaves room for ground differences of about a volt between the two ends before the receiver runs out of range. Beyond that a DC path between the grounds is needed, and a chunky ground wire in the cable is more reliable than an isolation barrier for short runs.

What the enable pin does at power up

The enable is common to all four drivers and is active in one polarity, so a board with several of these parts needs a decoder if the buses are to be driven independently. At power up the enable state is undefined until the controller drives it, and during that window a floating enable can put all four drivers on the bus at once. A 10 k pull resistor to the disabled state is the standard fix, and it is missing on a surprising number of boards.

The power off behaviour is specified separately: with the supply at zero the outputs present no more than 100 µA of leakage at 6 V, so a board that loses power releases the bus rather than clamping it. That is the feature that makes hot swap in a chassis possible.

Buying DS26C31TMX-NOPB

The reel is 2500 pieces and the tube is 48, both live. For a chassis product that uses two of these per board, a reel is a few hundred boards. For a service spares kit, the tube is the right quantity. The NOPB suffix means the part is lead free and RoHS compliant, and the older non NOPB strings are a different orderable row that should not be mixed in a build.

Because the die has been in production since the 1990s, the risk is not availability but counterfeiting on the brokered market. A part with this much age in a long life programme is exactly the profile that attracts relabelled stock, so the date code and the reel label matter more than the unit price.

Questions that arrive with this part number

Whether it can replace the AM26LS31 directly is the first question, and the answer is yes for the pin out and the function, with the caveat that the propagation delay and the enable polarity should be checked against the original. The second is whether a 3.3 V system can use it. It cannot, because the supply is 5 V and the inputs need TTL thresholds; the 3.3 V equivalent is a different family and a different part number.

The third is the difference between the M and T suffixes. The M is the military temperature part in ceramic or flat pack, the T is the industrial part in plastic, and the two are documented separately even though the function is the same.

Cable stubs are the other invisible variable. A 100 Ω pair with a 200 millimetre stub at the connector presents a discontinuity that reflects a fraction of the edge back into the driver, and at 6 ns edges that reflection arrives inside the bit window. Keeping stubs under 50 millimetres, or terminating at the stub, is the difference between a link that runs at 10 megabaud over 100 metres and one that produces an error every few minutes.

For a programme that is replacing an end of life RS-422 driver, the drop in verification page sets out the checks, and the date code page explains how we screen aged stock before it enters a build.