DRV8876QPWPRQ1
Product Specifications
DRV8876QPWPRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8876QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8876QPWPRQ1: the automotive row of the 700 mΩ bridge
The DRV8876QPWPRQ1 is the AEC-Q100 grade 1 member of the DRV8876 family, published ACTIVE with a 3000 piece reel. The die is the one described in the DRV887x documents: an N channel H bridge with a charge pump, a current mirror on the IPROPI pin, a regulation loop against VREF, three selectable input modes, and a quad level protection mode pin. The automotive document adds the qualification statement, the functional safety documentation reference, and a different reel quantity and marking.
The electrical limits are the same shape as the catalog part but the numbers are stated over the automotive temperature window, with the FET resistance quoted at 25 and at 150 degrees junction. That is the difference a buyer should look for when comparing a catalog and an automotive row: not a different function, but a narrower set of promises at the extremes.
The DRV8876QPWPRQ1 rows as the addendum publishes them
| Part class | Automotive brushed DC motor driver with current sense |
| Vendor status | ACTIVE, production data |
| Qualification | AEC-Q100 temperature grade 1, minus 40 to plus 125 ambient |
| Functional safety | Capable, documentation available from the vendor |
| Operating voltage | 4.5 V to 37 V |
| Peak output current | 3.5 A |
| RDS(on), both FETs | 700 mΩ at 25 degrees junction |
| RDS(on) at 150 degrees | Roughly 1.4 times the cold figure, per the family table |
| Current mirror ratio | 1000 µA per amp |
| Control modes | Phase and enable, PWM, independent half bridge |
| Protection mode | Retry or latched outputs, set by a resistor |
| Logic levels | 1.8 V, 3.3 V and 5 V compatible |
| Supply current | 3 mA typical, 7 mA maximum at 24 V |
| Sleep current | Under 1 µA at 24 V and 25 degrees junction |
| Charge pump | 5 V above VM, 400 kHz switching |
| Propagation delay | 650 ns |
| Output dead time | 300 ns |
| Undervoltage lockout | 4.3 to 4.6 V rising |
| Overcurrent trip | 3.5 A minimum, 5.5 A maximum |
| Thermal shutdown | 160 to 190 degrees, 20 degrees hysteresis |
| Body | HTSSOP with PowerPAD, 16 pins, 5.00 by 4.40 millimetres |
| Reel row | DRV8876QPWPRQ1, 3000 pieces, large tape and reel, Active |
| Marking | 8876Q |
| Lead finish | Nickel palladium gold |
| Moisture level | Level 3 at 260 degrees, 168 hours floor life |
The reel is 3000 pieces here against 2000 on the catalog row, and the marking carries a Q suffix. Those two facts are what a receiving inspection should check, because the package outline, the pin count and the body size are identical and a mixed tray of the two grades cannot be sorted by eye.
The automotive application set
The vendor lists body and comfort mechanisms: inlet locking for an on board charger, side mirror tilt and fold, seat and shifter adjustment, sirens and piezo drivers, servo actuators. All of these are short duty mechanisms with a mechanical stop, which is the profile that suits a driver with a current limit and a latch mode. None of them needs a torque loop, so the mirror is used as a limit rather than a measurement.
The charge pump matters in this set because a mirror fold motor is often driven at 100 per cent duty for a second and then held at a low duty to keep tension. Without a charge pump the high side FET would need a refresh every switching cycle and the hold would be a chopping waveform rather than a steady voltage.
Why the resistance number is quoted twice
A 700 mΩ bridge at 1.5 A dissipates 1.6 W cold and about 2.2 W hot, and the sixteen pin pad is the only exit for that heat. In a mirror housing the board is small and the ambient can reach 85 degrees, so the junction sits 40 to 60 degrees above ambient with modest copper, which lands near 145 degrees and inside the 150 degree limit but without much margin. That is why the automotive document states the resistance at both temperatures rather than only at 25.
If the mechanism needs more than 1.5 A continuously, the 8874-Q1 row at 200 mΩ is the correct choice and the footprint is unchanged. Sizing on the peak current instead of the continuous current is the most common mistake we see in these enquiries.
Protection and diagnostics in a safety context
The fault pin is a single open drain output, and the protection block distinguishes three events. For a functional safety argument the pin is a diagnostic, not a safe state: it reports that something happened, but the controller still has to decide what to do. The latched mode is the one that produces a defined safe state, because the outputs stay off until the controller clears the condition by cycling nSLEEP.
The undervoltage lockout has a 10 µs deglitch, which stops a short transient on the supply from dropping the bridge. During a cold crank the rail can fall below 4.3 V for tens of milliseconds, and that is long enough to trip the lockout, so the supply has to be held above the threshold by a boost or a diode and capacitor arrangement.
Buying DRV8876QPWPRQ1
One live reel row, 3000 pieces, level 3. No tube, no tray, no smaller carrier. For a programme at 20 000 units a year that is three reels, which is comfortable; for a 500 unit pilot it is one reel with most of it becoming stock. Automotive customers usually accept that because the grade requires a single lot trace, and splitting a reel across two builds breaks the trace.
The level 3 window is the production constraint. A reel opened for a pilot and then closed again needs a bake record before the next build, and the baking has to happen before the parts go into a kitting tray, not after.
Questions that arrive with this part number
Whether the automotive row can replace the catalog row on an existing industrial board is the first, and the answer is that it can electrically, with a different price and a different qualification record. The reverse substitution is the one to refuse, because it moves a qualified product onto an unqualified part. The second question is whether the ID pin on the package is a grade marker. It is not; the marking 8876Q on the top is the grade marker, and the ID pin is the pin one indicator.
The third is the temperature window at the board level. Grade 1 is minus 40 to plus 125 ambient, but that assumes the board itself is at ambient. A driver mounted next to a connector in a door module sees a local rise of 20 degrees or more, and the derating has to start from the local air temperature rather than the cabin figure.
The start-up sequence is the other place where the automotive environment bites. At 4.5 V the part is at the bottom of its range and the charge pump has only 5 V of headroom to build, so the wake time of 1 ms is measured from a supply that is already inside the window. A cranking profile that drags the rail through 4 V for 20 ms will hold the part in lockout, and the bridge will not respond until the rail is back above 4.45 V. A bulk capacitor sized on the harness resistance, typically 100 µF within 100 millimetres of the part, is what keeps the rail inside the window during that dip.
The quiescent current in sleep is specified below 1 µA at 24 V and 25 degrees junction, which is what allows the module to sit on a battery for months. At 125 degrees the same current rises by roughly an order of magnitude, and a module that is specified on the cold figure alone will show a parasitic drain in a hot soak test that nobody can explain from the data sheet headline.
For a programme comparing the automotive and catalog rows, the pin to pin page lists them side by side, and the PPAP checklist covers the records an automotive customer normally asks for before the first shipment.