Contact Us

DRV8876NPWPR

Brand: Texas Instruments
Texas Instruments DRV8876NPWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8876NPWPR — Power Management & Signal Chain | Superb Automation

DRV8876NPWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8876NPWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8876NPWPR: the DRV8876 without the current mirror

The DRV8876NPWPR is a sixteen pin automotive style H bridge that shares its pin out with the DRV8874 family but not its feature set. The differences are worth stating plainly, because the two strings are one letter apart and the boards they sit on look identical. The N version has no IPROPI pin and no VREF pin, which means no integrated current sense and no analogue current regulation. What remains is the bridge, the charge pump, the two logic inputs with their three control modes, the sleep mode, the spread spectrum clocking, and the protection block with a fault output.

Everything else matches the family. The operating range is 4.5 to 37 V, the peak drive is 3.5 A, the two FETs measure 350 mΩ each at 25 degrees and 420 mΩ maximum, and the device is qualified to AEC-Q100 grade 1 with functional safety documentation available. The reel carries 3000 pieces at moisture level 3, and the part marking is 8876N, which is the only way to tell it from the current sense version on a finished board.

The DRV8876NPWPR rows as the addendum publishes them

Part classBrushed DC motor driver, H bridge, no current sense
Vendor statusACTIVE, production data
Data sheetSLVSFE6A, August 2019, revised April 2021
QualificationAEC-Q100 grade 1, same family as the 8874
Operating voltage4.5 V to 37 V
Peak output current3.5 A
RDS(on), each FET350 mΩ typical, 420 mΩ maximum at 24 V and 1 A
RDS(on), both FETs700 mΩ typical
Supply current3 mA typical, 7 mA maximum at 24 V
Sleep current0.75 µA typical, 1 µA maximum at 25 degrees junction
Wake time1 ms from nSLEEP high to active
Charge pump voltage5 V above VM, switching at 400 kHz
Logic thresholds0.7 V low below 5 V, 0.8 V low above 5 V, 1.5 V high
Propagation delay650 ns
Output dead time300 ns
Rise and fall time150 ns each at 24 V
Undervoltage lockout4.3 to 4.6 V rising, 4.2 to 4.5 V falling
Overcurrent trip3.5 A minimum, 5.5 A maximum, retry after 2 ms
Thermal shutdown160 to 175 to 190 degrees, 20 degrees hysteresis
Body diode drop0.9 V at 1 A
BodyHTSSOP with PowerPAD, 16 pins, 5.00 by 4.40 millimetres
Reel rowDRV8876NPWPR, 3000 pieces, large tape and reel, Active
Tube rowDRV8876NPWPT, obsolete, no quantity, call vendor
Marking8876N
Moisture levelLevel 3 at 260 degrees, 168 hours floor life

Two rows carry a warning. The tube row is obsolete with a blank quantity, so any drawing that specifies a tube of these parts has to be changed to the reel before the next order. And the current sense rows that appear on the DRV8876 data sheet simply do not exist here, so a bill of materials that expects an IPROPI signal from this string will produce a board with two unconnected pads and no current feedback at all.

What is missing, and what that costs

Without the mirror there is no way for the controller to know the load current except by measuring it externally. The usual external circuit is a shunt in the ground return of the bridge, which brings back the two problems the integrated version removed: 0.05 Ω of extra resistance in the power path, and a small differential signal sitting on a switching node. At 3 A the shunt dissipates 0.45 W, which is more than the bridge itself loses at the same current, and that heat lands on the same board area.

What the N version does keep is the overcurrent protection at 3.5 to 5.5 A, which is a hard limit rather than a regulation loop. For a mechanism that only needs stall protection, that fixed limit is enough and the external shunt is unnecessary. For a mechanism that needs torque control, the N version is the wrong choice and the difference is not a resistor, it is a different part number.

The three input modes without a current loop

PMODE still selects phase and enable, PWM, or independent half bridge control, so the interface options are unchanged. The IMODE pin still selects automatic retry or latched outputs after an overcurrent event, because that decision belongs to the protection block rather than the sense block. That is the one place where the two versions behave identically, and it is worth knowing when a customer is migrating a board and only the current feedback is being lost.

The propagation delay of 650 ns and the 300 ns dead time are both shorter than the DRV8874 figures, because the smaller FETs switch faster. At 25 kHz that difference is invisible. At 50 kHz, where the period is 20 µs, 950 ns of combined delay is under 5 per cent of the period, which is still acceptable but starts to matter for a controller that measures duty cycle in software.

Thermal behaviour at 700 mΩ

At 2 A continuous the two FETs dissipate 2.8 W at the cold resistance and about 4 W at the hot one, which is at the edge of what a 5 by 4.4 millimetre pad can move into a four layer board. The practical rating for continuous operation on a modest copper area is nearer 1.5 A, and the 3.5 A headline belongs to short pulses and stall events. A customer who sizes a power supply around the peak number and then runs the motor continuously will see thermal shutdown within minutes, and the fix is a lower resistance member of the family rather than more copper.

The fault pin reports all three protection events on one line, so a scope is needed to tell them apart. Undervoltage recovers as soon as the rail returns, overcurrent retries after 2 ms, and thermal shutdown waits for a 20 degree drop. Counting the retry period on the fault line is the quickest way to identify which limit was hit without instrumenting the current.

Buying DRV8876NPWPR

The 3000 piece reel is the only live carrier, so the ordering question is the same as for the rest of the family: a full reel or a broken one with a documented bake. Because the part is level 3, a reel that has been open for more than 168 hours at workshop conditions needs 24 hours at 125 degrees before it can be used, and that is a production scheduling problem rather than a purchasing one.

The obsolete tube row matters for legacy drawings. A customer who has been buying 25 piece tubes for a service operation has to move to the reel and either consign the balance or ask a distributor to break it. Our kitting service handles that split and returns the balance in a moisture barrier bag, which is the only way the level 3 clock can be restarted legitimately.

Questions that arrive with this part number

The first is always whether this string can substitute for the DRV8876PWPR. It cannot, because the current sense pins are missing, and a substitution would silently remove the current limit that the controller relies on. The second is whether the N version is cheaper. It usually is, but the external shunt and its amplifier often cost more than the difference, so the saving is only real when no current measurement is needed at all.

The third is the difference between the N version and the DRV8874-Q1, which shares the footprint. The 8874 has 200 mΩ and 6 A with the mirror, the 8876N has 700 mΩ and 3.5 A without it, and the two are pin to pin. A board laid out for one can carry the other, and that is exactly why a bill of materials should record the exact suffix rather than the family name.

For a programme that is choosing between the family members on one footprint, the pin to pin page sets out the rows, and the drop in verification page covers what has to be checked before a substitution is signed off.