Contact Us

DRV88471RTER

Brand: Texas Instruments
Texas Instruments DRV88471RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV88471RTER — Power Management & Signal Chain | Superb Automation

DRV88471RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV88471RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV88471RTER: two H-bridges in a 3 mm square with the interface fixed to four pins

DRV88471RTER is the 3.00 mm by 3.00 mm WQFN member of the DRV8847 dual H-bridge family, a 16 pin body with an exposed thermal pad that drives two brushed DC motors, one bipolar stepper or two relay and solenoid loads from a single supply between 2.7 V and 18 V. Each bridge is rated at 1 A RMS at 25 degrees ambient, and the two bridges can be tied in parallel for 2 A when the thermal path allows it.

The code on the end of the part number is worth reading before anything else, because it decides what the board can and cannot be reconfigured to do later. The 88471 die has the bridge control mode fixed to the four pin interface and the torque scalar fixed at 100 percent. Those two pins are still on the package, but they no longer select anything. A board that needs the two pin interface, the parallel bridge interface or the independent half bridge interface has to take the DRV8847 instead, and a board that needs fault registers has to take the DRV8847S, which is the I2C variant.

The figures below come from SLVSE65C, revised December 2023, and from the orderable addendum at the back of the same document. They are the ones we check against a customer BOM before a quotation leaves the desk, because the two mistakes that cost money on this family are ordering the 88471 for a board that expects mode selection, and reading the 1 A rating as a number that holds at 85 degrees with both bridges loaded.

What the 88471 code takes off the table

On the DRV8847, the MODE and IN3 pins set one of four interfaces. On the DRV88471 the same pins are present and the mode is fixed to the four pin interface, so the controller has to supply four direction inputs and no mode decode. That is one line of firmware removed and one configuration step removed from the test fixture, and it is also one upgrade path removed: a customer who later wants to run the two bridges in parallel to reach 2 A cannot do it on this order code, because the parallel bridge interface is one of the modes that the fixed part does not offer.

The torque scalar behaves the same way. On the DRV8847, driving the TRQ pin changes the current regulation trip point between 100 percent and 50 percent, which is a way to hold a small motor at low speed without losing steps. On the DRV88471 the scalar is fixed at 100 percent, so the trip point is set once by the sense resistor and cannot be halved at run time. Boards that use the 50 percent state to reduce holding current in a battery product should be checked against the 8847 before the 88471 is written into the BOM.

What the 88471 keeps is the part that matters in a cost sensitive appliance: the two full H-bridges, the current regulation loop, the charge pump, the protection set and the nFAULT output. What it drops is the configuration layer. For a damper motor in a refrigerator or a feed motor in a printer, where the motion profile is fixed at the factory, the trade is a good one, and it is the reason this order code exists.

The specification that survives the quotation

FunctionDual H-bridge motor driver, one bipolar stepper or two brushed DC motors
Supply range2.7 V to 18 V on VM, single supply
Output current1 A RMS per bridge at 25 degrees ambient, 2 A RMS in parallel mode
On resistance1000 milliohm high side plus low side combined at 25 degrees, VM above 5 V
Control interfaceFour pin interface, fixed on this order code
Torque scalarFixed at 100 percent on this order code
Current regulationFixed 20 microsecond off time, trip point set by the sense resistor
Sense trip voltage150 mV typical, 140 mV minimum, 160 mV maximum at full torque
Sense blanking time1.8 microseconds
PWM frequency0 to 250 kHz on the IN pins
Logic levels1.8 V, 3.3 V and 5 V compatible inputs
Sleep current1.7 microamps at VM equal to 12 V and 25 degrees
Internal dead time200 nanoseconds
Body diode drop1.1 V
Undervoltage lockout2.7 V rising, 2.4 V falling, 50 mV hysteresis
ProtectionUndervoltage, overcurrent on each FET, short circuit, open load detection, thermal shutdown
Fault outputnFAULT, open drain, no fault registers on this order code
Thermal resistance46.4 degrees per watt junction to ambient for the RTE body
PackageWQFN, RTE, 16 pins, 3.00 mm by 3.00 mm, exposed thermal pad
Temperature rangeminus 40 to plus 125 degrees Celsius
CarrierLarge tape and reel, 3000 pieces, part marking 88471
Moisture levelLevel 1, 260 degrees, unlimited floor life

Fixed 20 microsecond off time and the 150 mV trip point

The current loop on this part is a chopper with a fixed off time. When the voltage across the sense resistor reaches the trip point, the bridge turns off for 20 microseconds, then the next cycle starts. The trip point is 150 mV typical, and the tolerance on that figure is the tolerance on the regulated current, because nothing else in the loop is trimmed. A 1 A regulation target with 150 mV across the sense resistor needs 150 milliohm, and that resistor dissipates 150 mW at full current, which in a 3 mm body is a real number to add to the thermal budget.

The off time sets the ripple, and the ripple is what decides whether the motor hears the chopper. With a 10 mH winding and 12 V across it, 20 microseconds of decay moves the current by 24 mA, so a 1 A setting runs between roughly 0.98 A and 1.0 A and the audible component sits near the chopping rate rather than in the motor. With a 1 mH winding the same 20 microseconds moves 240 mA, which is a 24 percent ripple on a 1 A setting, and at that point the average torque and the peak current are different enough that the sense resistor has to be chosen against the peak rather than the average.

The 1.8 microsecond blanking window is the other half of the same story. Every time a FET turns on there is a current spike from the body diode and the PCB capacitance, and the blanking window keeps the comparator from tripping on it. A board arrangement that adds more capacitance on the output nodes, for example a long cable to a remote motor, lengthens that spike and can make the loop trip on the spike rather than on the winding current. That is a board question, and it is the reason the datasheet asks for the sense resistor and the sense traces close to the device.

What 2 A in parallel costs in heat

The 2 A RMS figure in the feature list is a parallel mode figure with proper heat sinking at 25 degrees ambient, and the arithmetic behind it is worth doing once. One bridge carrying 1 A RMS through 1000 milliohm of combined on resistance dissipates 1 W. Two bridges loaded at the same time dissipate 2 W. With the RTE body at 46.4 degrees per watt junction to ambient, 2 W raises the junction 93 degrees above ambient, so a board at 25 degrees sits at 118 degrees junction and a board at 60 degrees inside an enclosure sits at 153 degrees, past the 125 degree ambient rating of the part.

That is not an argument against the part. It is an argument for loading one bridge at a time, or for keeping the average current below the RMS figure when both bridges run together. Stepper windings are a good case because both phases are energised at once, and the current per phase in a small stepper is usually 0.3 A to 0.6 A, which puts the pair at 0.2 W to 0.7 W and the rise at 10 to 33 degrees. A dual brushed motor appliance that runs both motors at 1 A continuously is the case that needs a thermal calculation before the quotation, not after the first prototype.

The 3.00 mm body with an exposed pad is the reason the number is as good as it is. The pad has to be soldered to a copper area with vias, and a pad that is connected but not thermally relieved behaves like the 107.9 degrees per watt of the TSSOP body. We see this on first articles regularly: the part is correct, the pad is present, and the copper under it is two 0.3 mm traces instead of a pour.

Fault reporting without the I2C registers

The 88471 reports one thing: the nFAULT pin pulls low when the device has latched or is retrying a fault. Undervoltage below 2.4 V, overcurrent on any FET, a short from an output to supply or ground, an open load detected in the off state, and thermal shutdown all end up on the same pin. There are no registers to read, so the controller cannot tell which one happened, and a service technician cannot either without a scope on the outputs.

For an appliance that is repaired by replacement this is acceptable. For a product that reports diagnostics to a host, it is not, and the answer is the DRV8847S, which puts the fault detail in I2C registers behind the same bridges. We raise that at the BOM review rather than at the prototype review, because swapping the order code later also changes the pin function of two pins and the firmware that reads them.

The open load detection is worth a note of its own. It works by pulling a small current into each output in the off state and watching the voltage, so a load that is present but has a parallel path, a snubber or a reverse protection diode to the rail, can read as open. If the fault pin is used in a self test at end of line, the fixture has to allow for that, and the test limit belongs in the test procedure, not in a tolerance band on the assembly drawing.

Termination, marking and the reel

The RTER suffix is the RTE body on a large tape and reel of 3000 pieces. The addendum prints the part marking as 88471, which is short enough that the lot code sits on the reel label rather than on the body, and that matters for traceability: a mixed reel cannot be sorted by reading the package. The moisture level is 1 with a 260 degree reflow ceiling and unlimited floor life, so the part does not need bake control on the line, unlike the AMC and BQ parts on this site that carry level 2 or level 3 ratings.

The lead finish is NIPDAU, nickel palladium gold, with tin also listed for the automotive graded row. Both are fine for a lead free process and both are fine for a HASL finish on the board. What we check on incoming is the reel count against the label, the pin one orientation mark on the tape, and the date code against the customer requirement, since a 3000 piece reel is enough for a long production run and a stale reel at the back of a shelf is a common finding.

What we check before a DRV88471 line ships

Component selection for this family runs through our power management cross reference, where the equivalent parts from other vendors are compared pin by pin and function by function before a second source is offered. When a customer asks whether a DRV8847 can replace a DRV88471 on an existing board, the answer is yes with the mode pins tied to the four pin setting and the torque pin tied to the 100 percent level, and the check for that is in our pin to pin cross reference.

On the assembly side the part is small, the pad is exposed and the pins are on 0.5 mm pitch, so the incoming plan covers coplanarity, the pad void percentage after reflow and a first article X-ray on the thermal pad. Our incoming inspection plan lists those three checks for WQFN bodies of this size, and the same plan covers the reel count and the moisture label. If a customer needs the lot traceability from reel to serial number, that is recorded at the point of use rather than at the point of receipt, and the report is available with the shipment.