Contact Us

TPS61232DRCR

Brand: Texas Instruments
Texas Instruments TPS61232DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61232DRCR — Power Management & Signal Chain | Superb Automation

TPS61232DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61232DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61232DRCR the fixed 5 V member of the 2 MHz boost family

The TPS61232DRCR is the fixed 5.0 V output version of the TPS6123x boost family, in the same 10 pin VSON body measuring 3 mm by 3 mm and 0.9 mm high. It takes 2.3 V to 5.5 V in, integrates a 5 A switch, and delivers up to 2.1 A at 5 V from a 3.3 V input at a quasi-constant 2 MHz. Because the divider is internal, the output accuracy is specified as a voltage rather than as a reference plus a divider tolerance.

The fixed version exists for a simple reason: a 5 V rail that has to be within a few per cent is easier to guarantee when the divider is inside the package. There is no external feedback node to pick up noise, no divider current to add to the quiescent budget, and no tolerance stack to compute. The trade is that the output cannot be trimmed at test.

Everything else is shared with the adjustable member: the pulse frequency mode at light load, the internal compensation, the input supply voltage supervisor with an adjustable threshold and hysteresis, and the complete disconnection of the load in shutdown.

Key parameters from the SLVSAQ2C document

Input range2.3 V to 5.5 V, one lithium cell or a 3.3 V rail
OutputFixed 5.0 V, specified as 4.9 V to 5.1 V in pulse frequency mode at light load
Output current2.1 A at 5 V from a 3.3 V input, set by the 5 A switch
Switching frequencyQuasi-constant 2 MHz in pulse width modulation, pulse frequency mode at light load
EfficiencyUp to 96 per cent at moderate load
Precharge550 mA current limit after enable, before the loop takes over
SupervisionInput supply voltage supervisor with adjustable threshold and hysteresis
Package10 pin VSON, 3 mm by 3 mm by 0.9 mm, DRC body, 3000 pieces on a large reel, moisture level 2
Order codeTPS61232DRCR on a 3000 piece reel and TPS61232DRCT on a 250 piece small reel

A fixed output removes a failure mode and a trim option

With an internal divider the feedback node is not exposed, so the usual problems with a high impedance node next to a switch node disappear. That matters at 2 MHz, where a few millimetres of trace on a feedback pin is enough to couple the switch edge into the loop and produce jitter that looks like noise on the output.

The cost is that a rail which needs 5.1 V at the far end of a cable cannot be trimmed. On a product where the load is a metre away and the cable drops 200 mV, the fixed part gives 4.8 V at the load and the adjustable version gives 5.0 V with a 5.2 V setting at the source. Choosing between them is a matter of whether the cable drop is in the specification.

The fixed version also draws no divider current, which on a 20 microamp class idle budget is a real difference. A 100 kilohm divider across 5 V draws 50 microamp, which is more than the converter itself at light load.

Where this part fits

USB charging accessories, portable instruments with a 5 V sensor bus, and any board where a fixed 5 V rail has to be reliable rather than trimmable. Our desk keeps the family comparison and the second source notes, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

The DRC body is shared with the adjustable member and with the discharge equipped member, so the suffix is the only distinction. The DRCR row is 3000 pieces on a large reel at moisture level 2, and the DRCT row is 250 on a small reel, with the same level. A prototype order that takes the R row leaves most of a reel on the shelf, and a level 2 part that sits open has a floor life to manage.

Confirm the input capacitor against the 2.3 V floor. A single cell product that runs to 2.5 V end of discharge leaves only 200 mV above the operating floor, and an input ceramic that loses capacitance under DC bias will let the ripple pull the part below it. Two 10 microfarad ceramics in parallel are a better answer than one 22 microfarad at that operating point. See incoming inspection plan for the receipt check.

Questions that come up on this part

What is the accuracy at full load, is the first question. The document gives 4.9 V to 5.1 V in pulse frequency mode at light load, and the loaded figure is set by the loop and the resistances, so the two numbers are not the same test. The second question is whether the part can be used as a 5 V pass through when the input is above 5 V. It cannot regulate down, so a product that has to accept a 5 V USB input and a 3.7 V battery needs an additional path.

The third question is about the supervisor. It watches the input, not the output, so it warns of a battery that is running out rather than a boost that has failed. Using it as a power good for the 5 V rail is a misreading of the pin function.