Contact Us

TPS61240DRVR

Brand: Texas Instruments
Texas Instruments TPS61240DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61240DRVR — Power Management & Signal Chain | Superb Automation

TPS61240DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61240DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61240DRVR 450 mA at 5 V from a 3.5 MHz boost in 2 mm square

The TPS61240DRVR is a synchronous boost converter in a 6 pin WSON body measuring 2 mm by 2 mm, with a fixed 5.0 V output at 2 per cent total DC accuracy, up to 450 mA of output current, and a 3.5 MHz switching frequency. It takes 2.3 V to 5.5 V in, so it runs from a single lithium cell or a three cell alkaline pack, and the whole solution including the inductor and two capacitors fits in about 13 square millimetres.

The input valley current limit is 500 mA on this member and 600 mA on the TPS61241, which is the only electrical difference between the two parts. Quiescent current is 30 microamp typical in power save mode, shutdown current is 1.5 microamp, and the start up time is 250 microsecond typical.

The converter uses a quasi-constant on-time valley current mode control, which gives a fast line and load transient response and allows small ceramic capacitors on both sides. At light load it moves automatically between pulse frequency and pulse width modes, and the transition is arranged to be invisible at the output rather than a step.

Key parameters from the SLVS806D document

Input range2.3 V to 5.5 V
OutputFixed 5.0 V at 2 per cent total DC accuracy
Output currentUp to 450 mA, with a 500 mA input valley current limit on this member
Switching frequency3.5 MHz typical
Quiescent current30 microamp typical in power save mode, 1.5 microamp in shutdown
Output ripple20 millivolt peak to peak at 200 mA from a 2.3 V input
Start up250 microsecond typical, with load disconnect during shutdown
ProtectionCurrent overload and thermal shutdown at 140 degrees with 20 degrees of hysteresis
Package6 pin WSON, 2 mm by 2 mm, DRV body, 3000 pieces on a large reel, moisture level 1

3.5 MHz shrinks the inductor and hardens the placement

At 3.5 MHz the inductor for a 450 mA boost is around 1 microhenry and can be a 0805 or a 2 mm square part, which is what makes the 13 square millimetre solution size real. The output capacitor can also be small because the ripple frequency is high, so two 4.7 microfarad ceramics are enough for the 20 millivolt figure.

The price is that the switch node edge is fast and the loop is sensitive to the physical arrangement. The input capacitor has to be at the VIN pin and the output capacitor at the VOUT pin, with a single ground point between them. A star ground with long returns will produce an output ripple that is larger than the table and a radiated emission that appears at the third harmonic.

The valley current limit sets the output current at a given input voltage. At 2.3 V in and 5 V out the input current is more than twice the output, so the 500 mA limit supports roughly 200 mA out, while at 4.2 V in the same limit supports close to 400 mA. The 450 mA headline belongs to the top of the input range.

Where this part fits

Sensor nodes, small displays, USB accessories and any board where a 5 V rail has to come from a single cell in a 2 mm square. Our desk keeps the boost cross reference and the pair comparison with the TPS61241, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The DRV body is 6 pins on 2 mm by 2 mm and the same body code appears on several 1 A and 2 A buck converters, so a reel label check is required. The DRVR row is 3000 pieces and the DRVT row 250, and the marking is OCJ. The TPS61241 in the same body has a 600 mA valley limit and is a legitimate upgrade when more output current is needed at low input voltage, but the higher limit also raises the peak inductor current.

Confirm the inductor saturation against 600 mA even on the 500 mA part, because the limit has a spread and the switch does not stop instantly. Confirm the output capacitor dielectric: at 3.5 MHz a small X5R is adequate, but an X7R of the same value will have a lower ESR and a slightly different loop response. See incoming inspection plan for the marking check on a six pin body.

Questions that come up on this part

Can it deliver 450 mA from a 2.3 V input, is the first question, and the answer is no, the valley limit caps the output at about 200 mA at that input. The second is whether the part can be shut down to less than a microamp. The shutdown current is 1.5 microamp, and the load is disconnected from the input at the same time, so the downstream circuit does not drain the cell through the boost.

The third question is about the 2 per cent accuracy. It is a total DC figure including line and load, which is tighter than most parts in this class quote, and it is the reason this device is used as a sensor supply rather than only as a logic rail.