Contact Us

TPS563202SDRLR

Brand: Texas Instruments
Texas Instruments TPS563202SDRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563202SDRLR — Power Management & Signal Chain | Superb Automation

TPS563202SDRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563202SDRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563202SDRLR 3 A buck in a 1.6 mm by 1.6 mm SOT563

The TPS563202SDRLR is a 4.3 V to 17 V, 3 A synchronous buck in a 6 pin SOT563 measuring 1.6 mm by 1.6 mm, with 95 milliohm high side and 57 milliohm low side FETs. It is the smallest body in this current class that still integrates both switches, and it needs no external compensation because the control is D-CAP2. The complete circuit is the device, a small inductor, two ceramics and a divider.

Output range is 0.806 V to 7 V, switching is a typical 580 kHz, and the feedback accuracy is 2 per cent at 25 degrees. Soft start is fixed at 1.2 ms, so there is no ramp capacitor to choose. Shutdown current is below 3 microamp, which is the number that matters for a board that has to meet a standby budget.

The light load behaviour is ECO mode, a pulse skipping scheme that keeps efficiency up when the load falls below a few tens of milliamps. The part also supports prebiased start, cycle by cycle overcurrent limiting with hiccup on a sustained fault, and non latching undervoltage and thermal shutdown. Junction range is 40 to 125 degrees.

Key parameters from the SLUSDL8B document

Input range4.3 V to 17 V, a wider low end than most parts in this class
Output current3 A continuous with 95 milliohm high side and 57 milliohm low side FETs
Output voltage0.806 V to 7 V, set by the feedback divider
Switching frequency580 kHz typical, fixed
Reference accuracy2 per cent feedback voltage accuracy at 25 degrees
Shutdown currentBelow 3 microamp with the enable pin low
Soft startFixed at 1.2 ms, no external capacitor
Package6 pin SOT563, 1.6 mm by 1.6 mm, DRL body, junction range 40 to 125 degrees

3 A in 1.6 mm square and what it costs

The die is small, so the FET resistances are 95 and 57 milliohm rather than the 20 to 40 milliohm of a larger body. At 3 A the conduction loss is about 0.5 W on the low side alone, and a 1.6 mm square body has very little pad to pass it into the board. The practical consequence is that 3 A is available at 25 degrees ambient with good copper, and about 2 A at 85 degrees in a sealed enclosure.

That is not a defect, it is the arithmetic of the package. A board that needs 3 A at high ambient should use a larger body with lower resistances, and a board that needs 1.5 A to 2 A in a tight space should use this one and stop worrying about it. Asking the part to do both is how thermal margin disappears.

ECO mode and the 3 microamp standby

Below a few tens of milliamps the part stops switching in a controlled pattern, which drops the quiescent draw and keeps efficiency above 80 per cent down to a milliamp. The output ripple in that mode is larger than in continuous conduction, so a load that cannot tolerate it needs a small LC filter or a different part. For a standby rail feeding a microcontroller, the ripple does not matter and the standby current does.

The 3 microamp shutdown figure is measured with the enable pin low, not in ECO mode. A board that quotes a standby budget has to distinguish the two, because ECO mode current is tens of microamps and shutdown is single digits.

Where this part fits

Set top boxes, routers, smart meters, appliance controllers and any 1 V to 3.3 V rail at 2 A in a space measured in millimetres. Our desk keeps the cross reference and the receipt checks for the small body class, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The DRL suffix is the 6 pin SOT563 at 1.6 by 1.6 mm, and it is a different footprint from the 6 pin SOT-23 used by the neighbouring 3 A devices, so a substitution in either direction needs a board revision. Confirm the output voltage divider against the 2 per cent accuracy budget, and confirm the thermal copper area if the load is above 2 A.

See incoming inspection plan for how we check a 6 pin marking that is often a single character, and date code management for high volume reels.

Questions that come up on this part

Can it deliver 3 A continuously, is the usual question, and the honest answer depends on ambient. At 25 degrees with a decent copper island, yes. At 85 degrees in a closed box, plan for 2 A. The second question is whether the fixed 1.2 ms soft start can be lengthened. It cannot, and a load that needs a slower ramp has to be handled by the enable timing instead.