Contact Us

DRV8818PWPR

Brand: Texas Instruments
Texas Instruments DRV8818PWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8818PWPR — Power Management & Signal Chain | Superb Automation

DRV8818PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8818PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8818PWPR: the 2.5 A stepper driver on the same 28 pin footprint

The DRV8818PWPR is a stepper motor driver in a 28 pin HTSSOP measuring 9.7 by 6.4 millimetres, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists two H-bridges with a microstepping indexer, full, half, quarter and eighth step modes, a step and direction interface, programmable decay and off time, up to 2.5 A per winding, an on resistance of 370 milliohms across the high and low side devices, an operating supply of 8 to 35 V, and protection against overcurrent, short circuit, undervoltage and overtemperature.

The 2.5 A rating and the 370 milliohm bridge are the two numbers that separate it from the 1.9 A sibling on the same pin out. At 2.5 A the bridge drops 0.9 V and dissipates 2.3 W, against 3.6 W for the smaller part at its own 1.9 A rating, so the larger part actually runs cooler at its rated current than the smaller one does at its. That is the reason a mechanism that needs 2 A should use this part rather than run the smaller one at its limit.

The DRV8818PWPR rows as the addendum publishes them

Part classBipolar stepper driver with an integrated microstepping indexer
Vendor statusACTIVE for the reel row, Obsolete for the tube row
Data sheetSLVSAX9G, September 2011, revised November 2025
Supply range8 V to 35 V
Current per windingUp to 2.5 A full scale
On resistance, high plus low side370 milliohms
MicrosteppingFull, half, quarter and eighth step
Chopping gainFactor of 8 on the sense voltage
Chopping accuracy5 per cent from 70 to 100 per cent of setting
Chopping accuracy, low range10 per cent from 20 to 56 per cent of setting
Reference input range0.05 V to the logic supply
Supply current7 mA typical, 10 maximum at 35 V
Logic supply current0.4 mA typical, 4 maximum
Sleep current3 microamps typical, 20 maximum at 35 V
Undervoltage, motor supply6.7 V rising, 7.5 V maximum
Undervoltage, logic supply2.75 V rising, 2.95 V maximum
Input hysteresis300 millivolts
BodyHTSSOP, 28 pins, 9.7 by 6.4 millimetres
Reel rowDRV8818PWPR, 2000 pieces, large tape and reel
G4 reel rowDRV8818PWPRG4, 2000 pieces, green material
Tube rowDRV8818PWP, Obsolete, blank quantity
MarkingDRV8818 on the body
Moisture levelLevel 3 at 260 degrees, 168 hour floor life
TemperatureMinus 40 to plus 85 degrees

The chopping accuracy rows are the ones that matter when the driver is asked to hold a position rather than to move. Five per cent from 70 to 100 per cent of the current setting and ten per cent from 20 to 56 per cent mean the same driver is four times less accurate at a quarter current than at full current, which is exactly where a microstepping driver spends its time when it is holding a position between two full steps.

What the electrical table fixes

The chopping current is set by the reference voltage divided by eight times the sense resistor, and the vendor gives the worked example: 3.3 V on the reference and 0.22 ohm on the sense gives 1.875 A. A customer who wants the full 2.5 A needs 0.165 ohm, which is not a standard value, so the practical choice is 0.15 ohm for 2.75 A, outside the rating, or 0.18 ohm for 2.29 A, inside it. That arithmetic is what decides the bill of materials, and it is not visible from the feature list.

The reference input range from 0.05 V to the logic supply means the current setting cannot be taken to zero by the reference alone. A driver that must disable the current entirely needs the sleep pin or the enable path, and a customer who expects a zero volt reference to give zero current will find a floor of about 28 milliamps at 0.22 ohm. That floor is the offset of the comparator and it is a real number in a positioning system.

The 7 milliamp supply current and the 3 microamp sleep current are the two ends of the power budget. A stepper that holds position draws the full winding current and the supply current is dominated by the bridge, not by the quiescent figure, so the sleep current only matters when the mechanism is parked and the driver is disabled. A battery product should use the sleep pin rather than leaving the bridge enabled with a zero reference.

Where the body fits on a board

The 28 pin HTSSOP at 9.7 by 6.4 millimetres carries two bridges and two sense paths, and the exposed pad is the thermal path for 2.3 W. The pin out is the same as the 1.9 A member, so a board can carry either part, and the copper under the pad should be drawn for the larger dissipation. A board that lays out the pad as a minimum footprint will run the die 30 degrees hotter than one that pours a plane, and the difference is invisible until a mechanism stalls in a warm enclosure.

The sense resistors are the components that decide the accuracy, and they need a Kelvin connection back to the sense pins. A trace that carries the winding current and the sense current together adds the trace resistance to the sense resistance, which changes the chopping current by the ratio of the two. At 0.18 ohm a 10 milliohm trace is a 5 per cent error, which is the whole accuracy budget of the driver at full current.

What the documents do not publish

The page gives the on resistance and the current but no curve of current against ambient, and no junction to ambient figure in the summary. It gives no microstep linearity figure, which is what a positioning system needs, and no output current waveform. Those are in the typical characteristics of the document and not on the product page.

The document is dated November 2025 in its current revision, which is recent, and it still does not print the external component values for the decay and off time on the page. A customer who is moving a board from another driver has to read the application section to translate the old component values, and a straight copy of the old values usually gives a different decay behaviour rather than an obvious fault.

Second source and long term availability

The pin compatible 1.9 A member is the natural second option on the same board, and it is a genuine fallback rather than a true second source, because it is the same vendor. A cross to another vendor is a board change. The pin to pin cross reference page sets out what we compare, and the component obsolescence management page covers the watch on the family.

Both the 1.9 A and the 2.5 A members have an obsolete tube row and a live reel row, which says that the vendor is packing for production and not for repair. A service organisation that buys tubes should move to reels or to a cut tape arrangement before the tube rows disappear completely. That is a planning item rather than a part item.

What to send with an enquiry

Send the exact string, the quantity and the date. State the winding current you need and the sense resistor you have, because the chopping current is the reference divided by eight times the resistor and the two have to be chosen together. State the supply voltage, since 35 V is two volts below the rest of the family.

Say whether the board will also build with the 1.9 A member, because that decides the copper and the current setting range. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.