DRV8804PWPR
Product Specifications
DRV8804PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8804PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8804PWPR: the four channel low side driver with a serial port
The DRV8804PWPR is a four channel protected low side driver in a 16 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists four N-channel field effect transistors with overcurrent protection, integrated inductive clamp diodes, a serial interface with a serial data output that can be daisy chained, an operating supply of 8.2 to 60 V, and maximum drive currents of 2 A on one channel and 1 A on four channels in the HTSSOP body at 25 degrees with proper heatsinking. The 20 pin small outline body is rated 1.5 A and 800 mA, and the SOT-23 thin body 1.9 A and 900 mA.
The four channels and the clamp diodes are what make this a relay and unipolar stepper driver rather than a general purpose switch. A relay coil generates a turn off transient that will destroy a bare transistor, and the diodes are inside the package so the board does not need four external ones. The serial interface with a data output means several packages can be chained behind one controller port, which is how a bank of eight or twelve relays is driven from a small controller.
The DRV8804PWPR rows as the addendum publishes them
| Part class | Four channel low side driver with clamp diodes |
| Vendor status | ACTIVE for the reel rows, Obsolete for the tube rows |
| Supply range | 8.2 V to 60 V |
| Channels | Four, N-channel, with overcurrent protection |
| Drive, HTSSOP, one channel | 2 A at 25 degrees with heatsinking |
| Drive, HTSSOP, four channels | 1 A per channel at 25 degrees |
| Drive, SOIC, one channel | 1.5 A at 25 degrees |
| Drive, SOIC, four channels | 800 mA per channel |
| Drive, SOT-23 thin, one channel | 1.9 A at 25 degrees |
| Drive, SOT-23 thin, four channels | 900 mA per channel |
| Clamp diodes | Integrated, for inductive turn off |
| Interface | Serial input with serial data output, daisy chain capable |
| Protection | Overcurrent, short circuit, undervoltage lockout, overtemperature |
| Fault reporting | Fault output pin |
| Body, HTSSOP | 16 pins, 5.00 by 4.40 millimetres |
| Body, SOIC | 20 pins |
| Reel row, HTSSOP | DRV8804PWPR, 2000 pieces, large tape and reel |
| Reel row, SOIC | DRV8804DWR, 2000 pieces, large tape and reel |
| Tube rows | DRV8804PWP and DRV8804DW, both Obsolete |
| Markings | DRV8804 on the HTSSOP, DRV8804DW on the SOIC |
| Moisture, HTSSOP | Level 3 at 260 degrees, 168 hour floor life |
| Moisture, SOIC | Level 2 at 260 degrees, one year floor life |
| Temperature | Minus 40 to plus 125 degrees |
The current ratings in that table are not one number. The same die gives 2 A in one body, 1.5 A in another and 1.9 A in a third, and the difference is the thermal path of the package rather than the silicon. A customer who sizes a relay coil against 2 A and then builds in the small outline body has a board that runs at 800 mA per channel when all four are on, and the relay will chatter before it fails.
What the electrical table fixes
The 60 V ceiling makes this a telecom and industrial relay driver rather than an automotive one. A 48 V relay coil with a turn off transient of 60 V or more is inside the rating only if the clamp diode is the integrated one, because the diode clamps the transient at the supply plus a diode drop rather than at an absolute maximum. A board that adds an external zener across the coil and expects the same result has changed the clamp voltage and the release time together.
The four channel current derating is a thermal statement, not a current limit. Each channel will deliver 2 A into a short for a moment before the overcurrent protection trips, and the 1 A figure for four channels is where the package can stay indefinitely. A customer who drives four relays that are never on at the same time can use the higher number, and a customer who drives four that are all on has to use the lower one.
The serial interface is a shift register, not a bus, so the number of devices in a chain is limited by the controller's tolerance for a long frame and by the clock rate rather than by an address. The data output pin is what makes the chain possible, and a board that does not route it has four devices that need four chip selects. That is a board decision that costs nothing at first article and a great deal at the second.
Where the body fits on a board
The 16 pin HTSSOP is the body with the exposed pad and the higher current, and it is the one to use when four relays are on together. The 20 pin small outline body is larger in footprint and lower in current, which is counter intuitive until the thermal path is considered: the small outline body has no exposed pad, so the die heat leaves through the leads. A customer who picks the SOIC because it has more pins has picked the slower of the two.
The integrated clamp diodes remove four components from the board, and they also remove the routing freedom that external diodes would give, because the return path is inside the package. A board that has the relay coils on a separate connector should bring the coil return back to the driver ground rather than to the chassis, otherwise the clamp current takes a path through the connector that was not intended for it.
What the documents do not publish
The page gives four current figures across three packages and no curve of current against ambient for any of them, so the derating has to be interpolated from the thermal table. It gives no on resistance figure in the summary, only in the electrical table, and no diode forward voltage for the clamps. Those three numbers decide the dissipation in a relay driver and none of them is on the first page.
The interface description does not print the frame length or the bit order on the product page. A customer who is writing a driver has to read section seven for the shift register definition, and a wrong bit order shows up as the wrong relay closing rather than as no relay closing. That is the kind of fault that takes a day to find and a minute to fix.
Second source and long term availability
Four channel low side drivers with integrated clamps are made by several vendors and the interface is usually a shift register, but the frame format and the current per body differ. The pin to pin cross reference page sets out what we compare, and the how to verify a drop in replacement page covers the bench checks.
Both tube rows on this part are obsolete and both reel rows are active, which is the same pattern as the rest of the family. A customer still buying tubes has a conversion to make, and the conversion is to a reel feeder rather than to a different part. The status of the three bodies is not the same, so a quote should name the body as well as the string.
What to send with an enquiry
Send the exact string, the body, the packing, the quantity and the date. State how many channels are on at the same time and for how long, because the current rating changes by a factor of two between one channel and four. State the coil voltage and whether the clamps are the integrated ones.
Say how many devices are chained and whether the data output is routed, since a chain of four needs a 32 bit frame and a chain of eight needs 64. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.