DRV8801PWPR
Product Specifications
DRV8801PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8801PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8801PWPR: the 2.8 A full bridge with a sense pin in an HTSSOP
The DRV8801PWPR is a full H-bridge motor driver in a 16 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the family as ACTIVE and lists an operating supply of 8 to 36 V, a peak output current of 2.8 A, an on resistance of 0.4 ohm typical across the high and low side devices, a phase and enable interface, a dedicated sleep pin, support for 100 per cent pulse width modulation duty cycle, an internal charge pump for the gate drive, and protection against undervoltage, charge pump undervoltage, overcurrent, short to supply, short to ground, overtemperature warning and overtemperature shutdown, with a fault pin to report them.
The two members of the family differ in one pin. On the DRV8800 the sense pin is a power return, and on the DRV8801 it is a sense input that a resistor converts into a current measurement. That is the whole difference, and it is the reason a board can move between the two parts with a resistor change and no other change. A customer who needs current limit in software wants the 8801 string, and a customer who only needs on and off wants the 8800 and does not need to pay for the sense path.
The DRV8801PWPR rows as the addendum publishes them
| Part class | Full H-bridge motor driver, phase and enable interface |
| Vendor status | ACTIVE for the reel row, Obsolete for the tube row |
| Data sheet | DRV8800 and DRV8801 family document |
| Supply range | 8 V to 36 V |
| Peak output current | 2.8 A |
| On resistance, high plus low side | 0.4 ohm typical |
| Sense voltage | 500 mV at the sense pin on the 8801 |
| Duty cycle | 100 per cent supported |
| Gate drive | Internal charge pump |
| Sleep mode | Dedicated pin, low quiescent current |
| Protection | Undervoltage, charge pump undervoltage, overcurrent, short to supply, short to ground |
| Thermal protection | Overtemperature warning and shutdown |
| Fault reporting | Open drain fault pin |
| Body, HTSSOP | 16 pins, 5.00 by 4.40 millimetres |
| Body, WQFN | 16 pins |
| Reel row, HTSSOP | DRV8801PWPR, 2000 pieces, large tape and reel |
| Tube row, HTSSOP | DRV8801PWP, Obsolete, blank quantity |
| Reel row, WQFN | DRV8801RTYR, 3000 pieces, large tape and reel |
| Marking | DRV8801 on the HTSSOP body |
| Moisture level | Level 2 at 260 degrees, one year floor life |
| Temperature | Minus 40 to plus 85 degrees |
| Absolute maximum, output to sense | 36 V |
The tube row is obsolete and the reel row is active, which is a pattern that runs through this whole family and through the motor driver catalogue in general. A customer who has been buying the two digit string and has a tube feeder will find that only the reel is supplied, and a line without a reel feeder has to change the feeder rather than the part. That is a production engineering question that arrives disguised as a purchasing question.
What the electrical table fixes
The 0.4 ohm on resistance across both devices sets the dissipation. At 2 A the bridge drops 0.8 V and dissipates 1.6 W, which in a 16 pin HTSSOP with an exposed pad is a rise of roughly 60 degrees against a 40 degree ambient, and that is why the 2.8 A figure is a peak and not a continuous rating. A customer who needs 2 A continuously should look at the thermal table before the current number, and should also look at the 100 per cent duty cycle claim, because a bridge that is chopping has a lower average dissipation than one that is held on.
The 500 mV sense threshold is the reference for the current limit. A 0.5 ohm sense resistor gives a 1 A limit, a 0.25 ohm resistor gives 2 A, and a 0.18 ohm resistor gives 2.8 A, which is at the peak rating of the part. The tolerance of the threshold and the tolerance of the resistor both land on the limit, so a board that needs a precise current limit needs a precise resistor and a calibration step, and a board that needs only a fault limit does not.
The 8 V minimum supply is the constraint that catches battery products. A 12 V rail is comfortable, a 9 V rail is inside, and an 8.4 V battery at the end of discharge is outside by 400 millivolts. A customer who plans to run this part from a two cell lithium pack should know that the bridge stops before the pack does, and the undervoltage lockout is the row to read rather than the nominal supply.
Where the body fits on a board
The 16 pin HTSSOP with the exposed pad is the body for a board that has a copper plane to solder the pad to, and the WQFN in the same pin count is the body for a denser board. Both are 16 pins and both carry the same functions, so a change between them is a footprint change and nothing else. The QFN reel is 3000 pieces against 2000 for the HTSSOP, which matters when a build quantity is expressed in reels.
The charge pump needs a flying capacitor and a reservoir capacitor, and both have to be close to the package because the pump switching is fast and the loop is short. A board that places them on the far side of the connector has a bridge that works at low current and misbehaves at high current, and the fault is easy to attribute to the part rather than to the placement. The vendor's application section gives the capacitor values and the placement rather than the feature list.
What the documents do not publish
The page gives a peak current and an on resistance but no safe operating area curve and no continuous current against ambient curve. Those are the two figures a thermal calculation needs, and they are in the typical characteristics of the full document rather than in the summary. The page also gives no switching time or propagation delay for the phase input, so a controller that commutates at high frequency cannot be checked from the summary.
The family document covers two parts and the pin function table marks the sense pin differently for each. A customer who reads the pin table quickly can conclude that both parts have a sense input, which is not the case. The difference is one letter in the pin description and it is worth stating explicitly in a quote.
Second source and long term availability
A 36 V H-bridge in a 16 pin package with a phase and enable interface is a common class and there are several candidates, but the pin out and the protection behaviour differ. The pin to pin cross reference page sets out what we compare, and the component obsolescence management page covers the case where one packing goes away and the other stays.
The tube row for this part is already obsolete while the reel row is active, and the QFN row carries a different reel size. A programme that needs a ten year supply should buy on the string that the vendor is still packing and should not rely on a tube that no longer exists. That is a planning decision rather than a sourcing one, and it is worth making before the last time buy window closes.
What to send with an enquiry
Send the exact string, the body, the packing, the quantity and the date. State the supply voltage range, because the 8 V floor rules out some battery products. State the current you need continuously and the current you need at peak, since the 2.8 A figure is a peak and the thermal limit is lower.
Say whether the sense pin is used for a current limit or left as a return, because that decides between the 8800 and the 8801 string and the two are not the same part. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.