DRV8718SQRVJRQ1
Product Specifications
DRV8718SQRVJRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8718SQRVJRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8718SQRVJRQ1: Eight Half Bridges in One Automotive Gate Driver, With Inline Current Sense
DRV8718SQRVJRQ1 is an automotive multi channel half bridge gate driver in a VQFN (RVJ) body of 56 pins. It drives eight N channel half bridges, so eight motors or a set of loads share one part, from a rail anywhere between 4.9 V and 37 V with a tripler charge pump that holds the high side gate up at 100 per cent duty. Drive strength is set by a resistor on the IDRIVE pin in six steps between 50 uA and 62 mA, dead time is managed by a handshake with three fixed settings added on top, and two wide common mode amplifiers measure current in line with the load rather than in the return path.
Order code and package
| Ordering string | DRV8718SQRVJRQ1 |
| Family document | DRV8714-Q1 and DRV8718-Q1, SLVSEA2E, revised March 2026 |
| Package | VQFN (RVJ), 56 pins |
| Reel and packing | 2000 pieces on a large reel |
| Lead finish and moisture | NIPDAU, level 3 at 260 C, 168 hour floor life |
| Temperature range | minus 40 to plus 125 degrees, AEC-Q100 grade 1 |
| Body marking | DRV8718S |
| Channel count | Eight half bridges on this part, four on the DRV8714-Q1 |
| Control | Four PWM inputs with output mapping, plus SPI for the detailed settings |
| Hardware mode | Simplified control with fewer MCU pins, and fixed drive settings |
| Current sense | Two wide common mode amplifiers, gain of 10, 20, 40 or 80 V/V |
| Charge pump | Tripler, for 100 per cent duty on the high side |
Electrical parameters that decide the application
| Operating range | 4.9 to 37 V, with 40 V absolute maximum |
| Charge pump | Tripler topology, so the high side gate stays above the rail at full duty |
| Peak source current | 50 uA to 62 mA, six settings on the hardware version |
| Peak sink current | 50 uA to 62 mA in the same steps |
| Output slew rate | Adjustable through the drive current, with a 60 pF load quoted at 2.5 V per us |
| Dead time | Handshake plus three fixed settings, with 10 per cent tolerance on the handshake |
| VDS overcurrent levels | Sixteen settings on the serial version, six on the hardware version |
| Blanking time | Eight settings on the serial version, fixed at 8 us on the hardware version |
| Current sense gain | 10, 20, 40 or 80 V/V, set by one resistor |
| Sense placement | Inline, high side or low side, because the amplifier common mode range is wide |
| PWM inputs | Four, multiplexed between the eight drivers |
| Protection | VDS overcurrent, charge pump fault, thermal warning and shutdown, all reported on a fault pin |
Family variants and how they differ
| DRV8718S-Q1 | This part, eight half bridges, serial interface |
| DRV8714S-Q1 | Four half bridges in the same family, pin to pin with fewer channels |
| DRV8718-Q1 hardware version | The same eight channels with a resistor set drive strength and no registers |
| DRV8873-Q1 | A single automotive bridge for one load |
| DRV8343-Q1 | A three phase gate driver with three shunt amplifiers |
| DRV8323 | The industrial smart gate driver for a three phase stage |
Points to check before this part goes on a BOM
Eight half bridges in one part is a packaging decision as much as an electrical one. A body control module with eight small motors, or a set of valves and lamps, gets one driver and one thermal pad instead of eight parts and eight sets of passives. The trade is that a fault on one channel can affect the diagnostics of the others, so the fault reporting has to be read through the serial port.
The 62 mA peak gate drive is small by three phase standards and correct for this application. These channels drive small FETs for lamps, valves and mirror motors, where a gate charge of a few nanocoulombs is typical and a 1 A driver would be wasted silicon. A large motor on one of the eight channels needs an external driver, and the part is not the right choice for it.
Inline current sense is the feature that separates this family from a plain gate driver. Measuring in series with the load, rather than in the return path, keeps the measurement valid during a recirculating window, which is exactly when a return path shunt reads zero. That is what allows a stall detection scheme to work on a load that is being chopped.
Dead time is a handshake with a 10 per cent tolerance, and three fixed settings are added on top. The handshake watches the gate of the FET that is turning off, so it adapts to the device and to temperature, and the fixed settings are the guard band for a slow module. A channel with a long cable to its load sees a different switching environment from one on the same board, which is why the setting is per channel on the serial version.
The revision history records a change to the VPOB_VDS threshold to 800 mV. That number is a comparator threshold on the drain to source voltage of a FET during the on time, and it appears in the fault reporting for a channel that is not being driven. A board that was characterised against the earlier threshold needs the fault mask reviewed when it moves to the current silicon.
Where eight half bridges earn their place
A body control module, a seat module, a door module or a small robot controller is the target. Each channel drives a brushed motor in an H bridge made of four external FETs shared between two channels, or a single ended load such as a lamp or a valve, and the four PWM inputs are mapped to the channels that need chopping. The rest are static on or off.
An automotive actuator cluster with several small motors and a diagnostic requirement uses the serial port. Each channel reports its own overcurrent, open load and thermal state, which is what a module has to send back on the bus when a customer complains that one mirror does not fold. A hardware only version of the same part gives one fault pin for all eight, which is enough for a cost sensitive module.
What has to be checked on a replacement
The channel count and the pin out, because the four channel and the eight channel parts are pin to pin only in the sense that the family shares a drawing. The 56 pin body carries all eight, and a board built for four does not have the copper for the other four.
The second item is the sense arrangement. This family measures inline, with a wide common mode range, so the amplifier sits between the FET and the load. A board that expects a low side shunt cannot use these amplifiers as they are wired, and the gain resistor sets a range that has to match the shunt.
Where this order code fits
The part suits an automotive or industrial module with several small motors, valves or lamps, where one driver with per channel diagnostics is worth more than eight separate bridges. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
How many Motors can it drive? Eight half bridges, which is four full H bridges or eight single ended loads, or a mix. The four PWM inputs are mapped to the channels that need a chopped drive.
Can it measure current in the return path? It can, because the amplifier common mode range covers low side, high side and inline placement. Inline is the reason the amplifiers exist, since a return path shunt reads zero during recirculation.
Does it need a serial port? The S version has one and uses sixteen drive and overcurrent settings. The hardware version sets the same functions with resistors and reports a single fault pin.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.