Contact Us

DRV602PWR

Brand: Texas Instruments
Texas Instruments DRV602PWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV602PWR — Power Management & Signal Chain | Superb Automation

DRV602PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV602PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV602PWR: the pop free 3 Vrms line driver on a 2000 piece reel

The DRV602PWR is a stereo audio line driver in a 14 pin TSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists 3 Vrms into a 2.5 kilohm load from a 5 V supply, 2 Vrms into the same load from 3.3 V, differential inputs with external gain setting resistors covering 1 to 10 volts per volt, a flat response from 20 Hz to 20 kHz, a signal to noise ratio above 102 decibels, total harmonic distortion plus noise below 0.05 per cent across the audio band, an output noise below 15 microvolts rms A weighted, and 8 kilovolt IEC electrostatic protection on the line outputs.

The architecture is the reason the part exists. It uses a charge pump to make a negative rail inside the package, so the output can swing below ground and centre itself at zero volts. That removes the large output coupling capacitors that a single supply driver normally needs, and it removes the low frequency roll off they cause. On a board where four 100 microfarad capacitors would take more space than the driver, the trade is obvious, and on a board where they cost nothing the simpler part wins.

The DRV602PWR rows as the addendum publishes them

Part classStereo line driver, differential input, single ended output
Vendor statusACTIVE, production data
Data sheetSLOS572D, December 2008, revised October 2010
Supply range3 V to 5.5 V, nominal 3.3 V or 5 V
Output into 2.5 kilohm3 Vrms at 5 V, 2 Vrms at 3.3 V
Output swing at 5 V8.5 volts peak to peak
Gain range1 to 10 volts per volt, external resistors
Frequency responseFlat from 20 Hz to 20 kHz
Signal to noiseAbove 102 decibels
Distortion plus noiseBelow 0.05 per cent, 20 Hz to 20 kHz
Output noiseBelow 15 microvolts rms, A weighted
Output electrostatic protection8 kilovolts IEC on the line outputs
Coupling capacitorsNone required on the outputs
Charge pumpInternal negative rail, flying capacitor on two pins
EnableDedicated pin, pop free on and off
Enable threshold high60 per cent of the supply
Enable threshold low40 per cent of the supply
BodyTSSOP, 14 pins
Reel rowDRV602PWR, 2000 pieces, large tape and reel
Tube rowDRV602PW, 90 pieces, tube
MarkingDRV602 on the body
Moisture levelLevel 1 at 260 degrees, unlimited floor life
TemperatureMinus 40 to plus 85 degrees
Absolute maximum supply5.5 V

The absolute maximum of 5.5 V is the row that causes field failures. A 5 V rail with a 10 per cent transient reaches 5.5 V, and a supply that overshoots on plug in reaches more. The part has no headroom above its own maximum supply, so a board that runs it from a 5 V rail derived from a 12 V input needs a clamp or a regulator with a defined overshoot. This is a small detail that is invisible in the feature list and expensive in a return.

What the electrical table fixes

The 3 Vrms output into 2.5 kilohms from a 5 V rail is 8.5 volts peak to peak, which is more than the supply rail. That is the charge pump doing its work, and it is why the part can be sold as a 3 Vrms driver on a 5 V supply without a transformer. On a 3.3 V supply the same load gets 2 Vrms, and a customer who specifies 3 Vrms and then runs the board at 3.3 V has specified a part that cannot deliver it.

The gain range of 1 to 10 volts per volt is set by external resistors, which means the gain accuracy is the resistor accuracy and not the amplifier accuracy. That also means a customer can build a second order low pass filter from the same two resistors around the input, which is what makes the part usable behind a converter that emits switching noise. The vendor states this in the description and it is the practical reason the inputs are differential and the gain is external.

The 102 decibel signal to noise figure is quoted against a full scale output and is not a noise floor in microvolts. The 15 microvolt rms A weighted figure is the one to compare against a converter output, and at 2 Vrms it is about 102 decibels, so the two are consistent. A customer who needs 110 decibels has to look at the higher grade part in the same family rather than at this one.

Where the body fits on a board

The 14 pin TSSOP is the same body as the rest of the family, so a board that was laid out for the 603 or the 604 can take the 602 with a resistor change in most cases. That is deliberate, and it is what lets a product family share one audio section across several price points. The moisture level 1 rating means the reel needs no bake, which matters on a small line that opens a reel and uses it across several weeks.

The charge pump needs a flying capacitor between two pins and a reservoir capacitor on the negative rail, and both are small ceramics. The vendor's note is that a capacitor smaller than 1 microfarad may work but the maximum output may be reduced and the part may not start, so the 1 microfarad value in the application section is a floor rather than a suggestion. A customer who has substituted a 100 nanofarad ceramic to save space has built a driver that clips earlier than the data sheet says.

What the documents do not publish

The page gives no load regulation curve and no output impedance figure, so a customer who needs to drive a 600 ohm load has to read the operational table rather than the feature list. It gives no crosstalk figure between the two channels, which matters when one channel drives a full scale signal and the other is idle. It also gives no turn on and turn off transient shape, only the claim that the part is pop free, and the transient is what the claim is about.

The document is from 2010 and the family has moved on. The vendor names the 603 as the footprint compatible part with higher signal to noise, trimmed offset and an external undervoltage mute, and it names the 604 for a stereo line plus headphone combination. A customer comparing the 602 with the 603 by price is comparing two parts that differ in the features that a portable product usually needs.

Second source and long term availability

Pop free line drivers with an internal charge pump are made by several vendors and the pin out is not standard, so a cross is a board change. The charge pump capacitor values and the gain network are the two items that have to be rechecked. The amplifier cross reference page sets out what we compare, and the how to verify a drop in replacement page covers the bench work.

The part is in its fourth revision of the document and the addendum rows are live at 2000 and 90 pieces. A 14 pin audio driver is not a part that a vendor withdraws quickly, but the family has a newer member, and a ten year programme should ask which member the vendor intends to keep in the long run.

What to send with an enquiry

Send the exact string, the packing, the quantity and the date. State the supply voltage and the load impedance, because 3 Vrms needs 5 V and 2.5 kilohms, and a 600 ohm load changes both the output and the distortion. State the gain you need, since the external resistors set it and a customer who expects a fixed gain has read the wrong part.

Say whether the board is shared with another member of the family, because the footprint is common and the string is not. The BOM scrubbing page explains how we reconcile a line like this against a build quantity before a schedule is confirmed.