DRV5013BCQDBZR
Product Specifications
DRV5013BCQDBZR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5013BCQDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5013BCQDBZR: the 12 mT latch in a surface mount body
The DRV5013BCQDBZR takes the same 12 mT latch die as the leaded member and puts it in a three pin SOT-23 measuring 2.92 mm by 2.37 mm. The supply range stays at 2.5 V to 38 V, the output stays open drain with 30 mA of sink capability, and the protection stays at minus 22 V of reverse supply and 40 V of load dump. What the surface mount body buys is placement on a board that is reflowed as a whole.
Twenty four volts of supply range in a small body is unusual, and it is the reason this part turns up in motor control boards that carry a 24 V bus and a 3.3 V controller on the same board. The sensor can be biased from the bus and its open drain output pulled to the controller rail, so no level shifter is needed between the two domains.
The chopper stabilized front end holds the operate point within 10 per cent over minus 40 C to plus 125 C, and the 35 microsecond power on time means a sensor that is powered from a switched rail reports a valid state almost immediately. The output is not a latch in the mechanical sense: it holds its state when the field is removed, which is what makes it usable as a rotor position memory across a power interruption of a few milliseconds.
Key data for the DRV5013BCQDBZR
| Type | Digital bipolar latch, toggles on alternating poles |
| Sensitivity | Operate point plus or minus 12 mT for the BC band, within 10 per cent over temperature |
| Supply | 2.5 V to 38 V, no external regulator |
| Output | Open drain, 30 mA sink, short circuit and current limit protection |
| Timing | 35 microsecond power on time |
| Protection | Reverse supply to minus 22 V, load dump to 40 V |
Body, packing and marking data
| Body | SOT-23 DBZ, 3 pins, 2.92 mm by 2.37 mm |
| Packing | 3000 pieces on a large reel, 178 mm carrier, 9 mm tape |
| Finish | Tin plated, moisture level 1, 260 C peak, unlimited floor life |
| Temperature | Minus 40 C to plus 125 C, marking 1UVJ on the published row |
Order code note before you place the string on a purchase order
The lettered row of this exact string is marked obsolete in the addendum while the plain row is active production at 3000 pieces on a large reel. That is the opposite of the usual pattern, where the lettered row is the current one, and it is a strong argument for reading the status column row by row rather than inferring it from the string.
Two other rows in the same family print a different carrier for the same package, one at 3000 pieces on a 202 mm carrier and one at 3000 pieces on a 210 mm carrier. Reel diameter and tape width are what a feeder is set up for, so the carrier dimension belongs on the purchase order when the line is already tooled for one of them.
Where a surface mount 38 V latch earns its place
Motor control boards, valve position sensing and flow meters on a 24 V bus use this part because it removes the regulator and the level shifter in one step. In a power tool the sensor sits inches from a switching drive, and the 12 mT operate point plus the chopper front end is what keeps the reading stable in that field.
Boards that were built around a leaded sensor and are being reworked to surface mount run into this part often, and the magnetic threshold is the number to compare, not the pinout. Our pin to pin cross reference page covers the electrical side, and the date code management page is where the reel date belongs when the sensor has to be traceable to a build lot.
Questions we get on this code
The first question is whether the 38 V rating covers a 24 V rail with a switching converter on it. It covers the steady state and a 40 V load dump, and it does not cover a repeated inductive spike above 40 V, which needs a clamp at the connector rather than a hope that the sensor absorbs it.
The second question is about the open drain output at 24 V. The output can sink 30 mA but it cannot pull up, so the resistor goes to the rail the controller reads, not to the sensor supply. Pulling up to 24 V and feeding a 3.3 V pin is the wiring mistake that ends with a damaged input. The pull up also sets the current the output sinks, so a 4.7 k resistor into 3.3 V draws about 0.7 mA, well inside the 30 mA the part can hold, and a 220 ohm resistor into the same rail draws about 15 mA, which is closer to the limit than most boards need.