Contact Us

TPS54628DDAR

Brand: Texas Instruments
Texas Instruments TPS54628DDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54628DDAR — Power Management & Signal Chain | Superb Automation

TPS54628DDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54628DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54628DDAR: 4.5 V to 18 V input, 6 A synchronous buck in SO PowerPAD

TPS54628DDAR is an adaptive on-time synchronous step-down converter with integrated switches in a SO PowerPAD body of 8 pins. The headline numbers are an 18 V input ceiling, a 0.76 V to 5.5 V output window and 6 A of continuous current from a 36 milliohm high-side and 28 milliohm low-side pair, switched at a fixed 650 kHz with D-CAP2 control and no external compensation parts.

Order code and package

Ordering stringTPS54628DDAR, DDA package, tape and reel
Package8-pin SO PowerPAD, 4.89 mm by 3.90 mm body
Thermal pathExposed pad on the underside, soldered to the board copper
Ambient range-40 C to 85 C, the industrial band and not the full automotive one
Pin count checkVIN, SW, VFB, VREG5, VBST, EN, SS and GND, all eight used in a normal circuit

Electrical parameters that decide the application

Input range4.5 V to 18 V, so a 12 V rail with 10 percent tolerance is inside
Output range0.76 V to 5.5 V set by a divider on VFB
Current6 A continuous, cycle-by-cycle limit on the low side
Switching frequency650 kHz fixed, no resistor to change it
Switch resistance36 milliohm high side, 28 milliohm low side
Shutdown currentBelow 10 microamp with EN low
Soft startAdjustable through the SS pin, and it starts into a prebiased output

Points to check before this part goes on a BOM

At 6 A the conduction loss is the first thing to count, and it is not small. Into 3.3 V from 18 V the duty cycle is 18.3 percent, so the high side carries 36 square amp times 36 milliohm for that share and the low side carries the rest at 28 milliohm: 0.24 W plus 0.82 W, just over 1 W dissipated before switching loss and gate drive are added, against 19.8 W delivered.

The 85 C ambient limit is the binding constraint in a sealed box and it is easy to miss because the part is sold as 18 V, 6 A. Every watt of that 1 W has to leave through the exposed pad, so the copper under the body is part of the current rating. A two-layer board with a small pad runs the junction far above the case, and the low-side switch is the one that heats first at high duty.

Duty cycle shrinks fast as the output falls. At 18 V in and 0.76 V out the on time is 65 ns at 650 kHz, which is close to where adaptive on-time control stops being able to hold regulation cleanly. The part is comfortable at 1.2 V and 1.8 V from a 12 V rail and becomes a compromise at the bottom of its output window from the top of its input window.

Ten microamp of shutdown current sounds like nothing until it is multiplied: 10 microamp for a year is 87.6 mAh, which is a fifth of a small coin cell. A board that keeps this rail off in standby but leaves VIN connected should check that EN really is below its threshold rather than floating, because a floating enable on a prebiased output restarts the converter.

D-CAP2 is the reason the bill of materials is short: no compensation network, and ceramic output capacitors are allowed because the loop tolerates very low ESR. That also means the output capacitor value and its ESR set the load-step response, so a substitution from the reference value to a smaller case size changes the transient result even though the capacitance reads the same.

Ripple current in the inductor is set by the 650 kHz frequency and the inductor value, and the ripple rating of the output capacitors follows from it. At 12 V in and 1.2 V out a 1.5 microhenry part sees about 2.4 A of peak-to-peak ripple, which is 40 percent of the 6 A rating and is what keeps the loop stable without external slope compensation.

The two small capacitors in the circuit are not decoration. VREG5 is an internal 5.5 V regulator that supplies the gate drive and needs about 1 microfarad to ground to stay stable, and the bootstrap capacitor of 0.1 microfarad between VBST and SW is what lets the high-side switch turn on at all. A board that omits either still starts and then behaves strangely under load, which is the worst kind of fault to find on a production line. Both are specified values with a specified place, close to the pins and with a short return path.

Where this order code fits

The usual fit is a 12 V or 18 V rail feeding a 1.2 V, 1.8 V or 3.3 V digital load in a set-top box, a home gateway or an LCD television, where the current is between 2 A and 6 A and the board has copper to spare under an 8-pin body. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is 6 A the current I can take continuously at 85 C? Only with the exposed pad soldered to enough copper. The 6 A figure is the switch and limit rating; the continuous number in a sealed enclosure comes from the 1 W of conduction loss and the thermal resistance the board gives the pad.

Can I replace a 5 A part in the same footprint? Compare the pinout and the reference divider first, then the inductor and output capacitors. The control loop is internal and fixed at 650 kHz, so a part with a different frequency needs the inductor and capacitor values rechecked rather than copied.

What happens on a shorted output? The low-side cycle-by-cycle limit holds the peak current, and the part restarts when the fault clears. There is no latch, so a persistent short becomes a repeating hiccup at the current limit rather than a dead rail.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.