Contact Us

TPSM83100SIUR

Brand: Texas Instruments
Texas Instruments TPSM83100SIUR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM83100SIUR — Power Management & Signal Chain | Superb Automation

TPSM83100SIUR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM83100SIUR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM83100SIUR: 1.5 A Buck-Boost Module With an Integrated Inductor

TPSM83100SIUR is a buck-boost power module with the inductor inside the package in a 8-pin uSiP body of 8 pins. It regulates from 1.6 V to 5.5 V in to between 1.2 V and 5.5 V out at 1.5 A, with the inductor in the package, so the only external parts are the two capacitors.

Order code and package

Ordering stringTPSM83100SIUR, uSiP-8 (SIU), 2.3 mm by 2.9 mm, 1.35 mm high
FamilyTPSM83100, TPSM83101 and TPSM83101L, the last with a different soft start
Input1.6 V to 5.5 V
Output1.2 V to 5.5 V, 1.5 A
Modeautomatic power save and forced PWM, selected on the MODE pin
Capacitors4.2 uF effective input, 10.4 uF effective output at 3.3 V

Electrical parameters that decide the application

Switch resistanceQ1 45 mOhm, Q2 50 mOhm, Q3 50 mOhm, Q4 85 mOhm
Shutdown current0.5 uA typ, 0.9 uA max
Quiescent into VIN0.15 uA typ, 6.1 uA max, not switching
Quiescent into VOUT8 uA, not switching
UVLO rising1.5 V to 1.599 V
UVLO falling1.4 V to 1.499 V
Power on reset1.25 V to 1.65 V on the higher of input and output
EN and MODE thresholds0.77 V to 1.2 V high, 0.5 V to 0.76 V low
Threshold hysteresis300 mV
Thermal resistance100 C/W junction to ambient

Points to check before this part goes on a BOM

The four switches add up in pairs, and the worst pair is 95 mOhm. Delivering 1.5 A at 3.3 V from a 1.8 V input draws 3.24 A at 85 percent efficiency, which through 95 mOhm is 1.0 W. At 100 C/W that is a 100 C rise, so 1.5 A at the bottom of the input range is not a continuous rating, and the same 1.5 A from a 3.6 V input is a different thermal proposition.

The quiescent current into VIN is 0.15 uA typical and 6.1 uA maximum, a forty fold spread that comes from process and temperature. A product that quotes a year of standby from the typical number is quoting a number one part in two will not meet, and the 8 uA flowing into VOUT adds to it.

Shutdown at 0.9 uA maximum is 7.9 mAh over a year, so the difference between shutdown and no load operation is a factor of about seven, not the factor of a thousand a user expects from a module with an enable pin.

The power on reset window of 1.25 V to 1.65 V applies to the higher of input and output, so a module fed from a 1.2 V rail is held off until that rail is above 1.25 V, and a module whose output is pre-biased to 1.5 V starts with a defined state instead of a race.

The 300 mV of hysteresis on EN and MODE is large for a 1.2 V threshold and is there to keep a slow rising supply from toggling the mode pin. It also means an enable signal that swings between 0.8 V and 1.1 V is inside the band and produces no defined state.

The module is 1.35 mm high with the inductor inside, which leaves 6.7 square mm of board and no switching node to route, but it does not remove the inductor's current: 1.5 A at 3.3 V from a 2 V input is 4.95 W out, and at 85 percent efficiency that is 2.9 A of input current through the same inductor. A module held at 1.5 A in a hot boost is at its current limit, not at a thermal limit.

Eight microamps flow into VOUT when the module is not switching, which is 70 mAh over a year and larger than the 6.1 uA maximum into VIN. A load that is switched off but still connected to the output sees that current, so the standby figure for the product is the sum of both pins and not the smaller one, and the difference shows up only in a long battery test.

Where this order code fits

Optical modules, portable instruments, meters and telematics units use this module where a rail has to stay in regulation while a battery moves above and below it. A radio module whose power amplifier needs 3.3 V while the battery moves from 4.2 V down to 3.0 V is the case the buck-boost exists for, and a meter that has to keep its rail alive at the end of a lithium cell uses the same part for the same reason. The 1.35 mm height also clears a shield can with a 1.6 mm keep out, which is the mechanical reason it appears in optical assemblies. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Is the inductor really inside? Yes, that is what the uSiP package is: the inductor and the four switches are in a 2.3 mm by 2.9 mm body, and the datasheet recommendation is two capacitors and nothing else.

Does it regulate when the input equals the output? It passes through the body of the buck-boost, which is the case the module is built for; efficiency in that region is lower than in pure buck or pure boost.

What is the difference between the 83100 and the 83101L? The soft start: the L version has a slower ramp for a load that cannot take an inrush, and the external components are the same.

Can two modules be paralleled? No. Each regulates to its own reference and there is no current sharing pin, so two in parallel fight at the point where their setpoints differ.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.