TPS54228DDAR
Product Specifications
TPS54228DDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54228DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54228DDAR: 18 V Input, 2 A Synchronous Converter in SOIC-8 With 800 uA Operating Current
TPS54228DDAR is a D-CAP2 synchronous buck converter with both FETs inside in a 8-pin SOIC body of 8 pins. It converts 4.5 V to 18 V into 0.76 V to 7 V at 2 A, switches at a fixed 700 kHz, and draws 800 uA from the input with 5 uA in shutdown.
Order code and package
| Ordering string | TPS54228DDAR, SOIC-8 (D), 4.89 mm by 3.90 mm, tape and reel |
| Other packages | HSOP-8 (DDA) and VSON-10 (DRC), 3 mm by 3 mm, same silicon and different heat path |
| Input | 4.5 V to 18 V, with a 5.5 V internal regulator derived from the input |
| Output | 0.76 V to 7 V adjustable, 0.765 V reference in continuous conduction |
| Current | 2 A continuous, 2.3 A to 4.7 A peak current limit depending on the package |
| Switching frequency | 700 kHz fixed, no resistor, one frequency for the family |
| Temperature | -40 C to +85 C ambient, thermal shutdown at 165 C with 35 C of hysteresis |
Electrical parameters that decide the application
| High-side resistance | 155 mOhm in the HSOP and VSON, 165 mOhm in the SOIC package |
| Low-side resistance | 108 mOhm at 25 C, the dominant conduction term at high duty |
| Reference | 765 mV typical, 749 mV to 781 mV, plus or minus 2.1 percent over temperature |
| Operating current | 800 uA typical, 1200 uA maximum, non-switching at 12 V in |
| Shutdown current | 5 uA typical, 10 uA maximum, enable pin low |
| Minimum off time | 260 ns typical, 310 ns maximum, so the duty ceiling is 78.3 percent |
| Input lockout | 3.75 V typical on the internal 5.5 V rail, 0.32 V of hysteresis |
| Thermal resistance | 45.3 C/W in HSOP, 114.4 C/W in SOIC, 43.9 C/W in VSON |
| Internal regulator | 5.5 V at 60 mA available to external loads, a linear regulator from VIN |
Points to check before this part goes on a BOM
This order code is the SOIC, and its 114.4 C/W junction to ambient against 45.3 C/W for the HSOP is the single most important line in the datasheet. At 0.6 W of loss the same die runs 69 C above ambient in the SOIC and 27 C above in the HSOP, so a 60 C cabinet leaves the SOIC at 129 C and the HSOP at 87 C. The part number decides the thermal answer before the copper does.
The current limit in the D package is 2.3 A minimum against a 2 A rating. At 18 V in with a 2.2 uH inductor the duty is 5.83 percent and the ripple is about 0.64 A, so a 2 A load peaks at 2.32 A, which is on the minimum limit line. A larger inductor or a lower input voltage moves the peak down; a 12 V input with the same inductor gives 0.44 A of ripple and 0.22 A of headroom.
The 78.3 percent duty ceiling from the 310 ns minimum off time explains the 7 V output figure: from a 9 V input, 7 V is 77.8 percent and just fits, while from the 4.5 V minimum input the highest reachable output is 3.52 V. The headline range is therefore two ranges, one for a 12 V rail and one for a 5 V rail, and a 7 V load on a 5 V input is not a supported combination.
800 uA of operating current is 7.0 Ah over a year, against 43.8 mAh in shutdown, and Eco-mode is what keeps a light load from paying the switching loss on top. A 2 mA standby load on a 12 V input costs 24 mW of input power before the converter's own 9.6 mW, so the quiescent term is a third of the budget at that load.
The internal 5.5 V regulator can supply 60 mA to external circuits, but it is a linear regulator fed from the input: at 18 V in and 60 mA it dissipates 0.75 W inside the same package that is already carrying the converter loss, which in the SOIC is another 86 C of rise. Using it for a housekeeping load is a package decision, not a free output.
The reference is 765 mV with a 0.1 uA maximum bias current at the feedback pin, so the divider current can be as low as a few microamps and still dominate the bias term. A 10 kohm top resistor carries 76 uA, 760 times the bias current, which is the normal choice; going to 1 Mohm for standby savings would put the bias error at 3 percent of the reference.
Where this order code fits
It is used in digital television and set-top power supplies, Blu-ray players, home gateways and any 12 V board that needs a 5 V, 3.3 V or 1.2 V rail at 2 A with a small component count, and the 700 kHz frequency keeps the inductor and the ceramic output bank compact. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.
Questions buyers ask
Is the SOIC the same part as the HSOP? Same silicon, different heat path: 114.4 C/W against 45.3 C/W, so the SOIC carries roughly half the continuous loss at the same ambient.
Can the output reach 7 V? Only from an input above about 9 V, because the 310 ns minimum off time caps the duty at 78.3 percent.
What is the fifth pin regulator for? It makes 5.5 V at up to 60 mA for external logic, at the cost of linear dissipation inside the converter package.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.