Contact Us

TPS3808G33DBVR

Brand: Texas Instruments
Texas Instruments TPS3808G33DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3808G33DBVR — Power Management & Signal Chain | Superb Automation

TPS3808G33DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3808G33DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3808G33DBVR: Supervisor with a delay that can be programmed from 1.25 ms to 10 s

TPS3808G33DBVR is a supervisory circuit in the six pin DBV body that watches a 3.3 V rail with 0.5 percent accuracy, draws 2.4 uA and holds its open drain reset low for a delay set by a single capacitor anywhere from 1.25 ms to 10 s in a SOT-23-6 body of 6 pins. The TPS3808 supervises a rail between 0.4 V and 5 V and provides a reset output with a delay that is set by a capacitor on the CT pin, from 1.25 ms to 10 s. An open CT pin gives 20 ms and a CT pin tied to the supply gives 300 ms, so the two most common values need no component at all. The threshold accuracy is 0.5 percent for rails at or below 3.3 V, the quiescent current is 2.4 uA, and a manual reset input allows the processor to be reset by a button or by another device.

Order code and package

Order codeTPS3808G33DBVR
Supervised voltage3.3 V, threshold 3.07 V typical
Threshold accuracy0.5 percent for rails at or below 3.3 V
Reset delay range1.25 ms to 10 s with a capacitor on CT
Reset delay, CT open20 ms
Reset delay, CT tied high300 ms
Reset outputopen drain, active low
Packagesix pin SOT-23, DBV body

Electrical parameters that decide the application

Quiescent current2.4 uA typical
Fixed threshold options0.9 V to 5 V in steps, plus an adjustable 0.4 V version
Manual reset inputprovided, with an internal pull up
Minimum CT capacitance100 pF for a user programmed delay
Temperature rangeminus 40 C to 125 C
Supply voltage range1.7 V to 6.5 V in the electrical table
Output low voltage0.3 V at 0.4 mA on a 1.3 V supply
Alternate package2 mm by 2 mm WSON

Points to check before this part goes on a BOM

The delay range spans four decades from one part number, which is unusual and useful. Twenty milliseconds is the right delay for a supply that ramps in a millisecond, and ten seconds is the right delay for a supply that charges a large capacitance through a current limited source. Because the value is set by a capacitor, the same part can serve both cases, and the decision moves from the purchasing list to the bill of materials, which is where a change is cheap.

The threshold of 3.07 V on a 3.3 V rail is 93 percent of nominal, which leaves 230 mV between the trip point and the rail. A processor that runs to 3.0 V has 70 mV of margin between the trip point and its own minimum, and the 0.5 percent accuracy of the threshold is 15 mV of that. That is a workable window, and it is the window the two numbers describe: the supervisor trips before the processor leaves its specification, with enough margin that the tolerance of the rail and the tolerance of the trip point do not overlap.

A 2.4 uA quiescent current is 21 mAh over a year, which is a tenth of a coin cell and one percent of a lithium cell. That is low enough that the supervisor is not the thing that decides the standby life, and high enough that it is not free: a product with a 500 nA budget has to use a different approach, such as a supervisor that is powered from a switched rail.

The open drain output is a board constraint as well as a convenience. It can be wired to another open drain output to form a wired OR reset, which is how a manual reset button and a supervisor are combined without a gate. It cannot source current, so a processor with an active low reset and an internal pull up is the natural load, and a processor that needs a driven high has to have a pull up resistor sized for its input current.

The manual reset input has an internal pull up and a debounce that is part of the specified behaviour. A button connected from the pin to ground pulls it low and holds the reset asserted for as long as the button is held plus the delay after release. That combination means the reset length depends on how long a human presses, which is the right behaviour for a front panel button and the wrong behaviour for a signal from another device that pulses briefly.

The minimum capacitance of 100 pF is the point below which the delay is set by the pin's own capacitance and the internal timing rather than by the component. A board that needs a delay shorter than 20 ms cannot get there with a capacitor, because the range starts at 1.25 ms only above that capacitance, and the practical way to a shorter delay is a different part rather than a smaller capacitor. The numbers to keep in mind are 100 pF for the bottom of the range and an open pin for 20 ms.

The supply range of 1.7 V to 6.5 V in the electrical table is wider than the rails it supervises, because the part needs to keep working while the rail it watches is collapsing. A 3.3 V rail that falls to 2 V still has a working supervisor, so the reset stays asserted rather than floating. The absolute minimum for the output to be defined is lower still, and that is the interval that matters in a product that loses power without warning.

Where this order code fits

This order code belongs on processor rails in portable and battery powered products, notebook and desktop computers, handheld instruments and industrial controllers, where the rail has to settle before the processor is released. It is also the part chosen where the release time has to be tuned to a power supply rather than to a processor, because a slow ramping supply needs a longer reset delay than a fast one and a capacitor is a cheaper answer than a different part number. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

How is the reset delay set? By a capacitor on the CT pin, from 1.25 ms to 10 s. An open pin gives 20 ms and a pin tied to the supply gives 300 ms, so the two common values need no component. The capacitance has a 100 pF floor, below which the delay is set by the pin rather than by the component.

Why does the threshold sit at 93 percent of the rail? So that the reset asserts before the processor leaves its own specification. On a 3.3 V rail the trip is 3.07 V, which leaves 70 mV of margin to a processor rated at 3.0 V, with 15 mV of that consumed by the 0.5 percent threshold accuracy. The remaining margin covers the divider and the reference drift over temperature.

Can two reset sources be combined? Yes, because the output is open drain. A manual reset button and the supervisor can drive the same node, and whichever pulls low asserts the reset. The pull up resistor has to be sized for the processor's input current and for the rise time of the node, which is a short list of two numbers that a board should record.

Does the manual reset input need a debounce? The pin has an internal pull up and the reset is held for as long as the pin is low plus the delay after release, so a mechanical button produces one reset rather than a burst. A device driving the pin with a short pulse produces a reset whose length is the pulse plus the delay, which is usually what the driving device intended.

SUPERB holds and sources this supervisor line against the exact order code, with the reel, date code and country of origin stated on the offer. When a reset circuit has to move to a second part, the BOM Shortage Recovery page sets out the checks that separate a working substitute from one that fails on the bench.