Contact Us

DLPA3005DPFDR

Brand: Texas Instruments
Texas Instruments DLPA3005DPFDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DLPA3005DPFDR — Power Management & Signal Chain | Superb Automation

DLPA3005DPFDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DLPA3005DPFDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DLPA3005DPFDR: the 16 A LED driver version of the projector power IC

The DLPA3005DPFDR is the higher current member of the projector power management pair, a 100 pin HTQFP measuring 14.00 by 14.00 millimetres, supplied 1000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists drivers for external buck field effect transistors up to 16 A per LED and up to 32 A for series LEDs, drivers for external RGB switches, 10 bit programmable current per channel, the three mirror supplies, two buck converters for the display controller and mirror, an 8 bit programmable auxiliary buck, two low dropout regulators at 2.5 V and 3.3 V for 200 mA, an analogue multiplexer, and thermal shutdown, hot die and undervoltage protection.

The difference from the 3000 is where the current comes from. The 3000 integrates the buck switch and stops at 6 A, the 3005 drives external field effect transistors and reaches 16 A per channel, which is why the two parts share a package and a pin count but not a bill of materials. A board built for the 3005 carries three extra power transistors, their gate drive components and a larger inductor, and that difference is invisible on the product page and decisive on the cost sheet.

The DLPA3005DPFDR rows as the addendum publishes them

Part classProjector power management IC with an external FET LED driver
Vendor statusACTIVE for the D suffix, LIFEBUY for the C suffix
Data sheetDLPS071A, October 2015, revised February 2023
LED currentUp to 16 A per channel, 32 A for series LEDs
Current setting10 bits per channel, register programmable
Switch driveExternal RGB switch drivers
Buck convertersFive, two dedicated to the controller and mirror supply
Auxiliary buck8 bit programmable, fan or auxiliary rail
Low dropout regulatorsTwo, 2.5 V and 3.3 V, 200 mA each
Mirror suppliesBias, reset and offset generated on chip
Input voltage6 V to 20 V on the supply pins
Switch and feedback pins0.1 V to 20 V
SPI supply1.7 V to 3.6 V, separate pin
Ambient temperature0 to 70 degrees
Junction temperature0 to 120 degrees
Thermal, junction to ambient7.0 degrees per watt with the vendor heatsink
Thermal, case to board3.4 degrees per watt characterization parameter
BodyHTQFP, 100 pins, 14.00 by 14.00 millimetres
Tray rowDLPA3005DPFD, 90 pieces, JEDEC tray
Reel rowDLPA3005DPFDR, 1000 pieces, large tape and reel
Lifebuy rowsDLPA3005CPFD and DLPA3005CPFDR, C suffix, call TI
MarkingDLPA3005D on the reel body
Moisture levelLevel 2 at 260 degrees, one year floor life

The lifebuy rows are the ones to read first. The C suffix parts carry a LIFEBUY status with a blank quantity and a call the vendor note, which means the older silicon is at the end of its life and only the D suffix is being supplied. A customer whose board was qualified on a C suffix part has a last time buy decision to make now rather than later, and the two suffixes are not always interchangeable on a board that was tuned around the older one.

What the electrical table fixes

The 16 A figure is an external switch current, not a converter output, so the inductor, the sense resistor and the field effect transistor all have to be sized for it. At 16 A with a 30 milliohm transistor and a 20 milliohm sense element, the conduction loss alone is 16 squared times 0.05, which is 12.8 watts, and that is more than the package can pass to a heatsink at 7.0 degrees per watt without a fan. The current is real and the thermal path is the constraint, exactly as on the 3000.

The series LED support is the new capability in the current revision, and it changes the input requirement. Two strings in series need twice the forward voltage, so a 20 V ceiling on the input pins sets the maximum string length rather than the maximum current. The vendor's revision note records that series LED support was added to the RGB strobe decoder, which is the block that decides which channel is active and when, so an older board cannot be assumed to support series strings after a software update.

The 0 to 70 degree ambient range and the 120 degree junction limit are the same as the smaller part. The margin between them, at 7.0 degrees per watt, is 50 degrees of junction rise for the full 7 watts of dissipation. A 16 A build at 3.3 V of string voltage dissipates 52 watts in the LED, not in this part, so the part survives while the LED package is the component that needs the thermal attention.

Where the body fits on a board

The package is the same 100 pin HTQFP as the 3000, but the surrounding board is larger because the external switches, the inductors and the current sense resistors all sit beside it. A 16 A rail needs a copper pour measured in tens of square millimetres per component, and the sense resistor has to be a low inductance type with a Kelvin connection, otherwise the current reading carries the switching edge and the loop becomes unstable.

The SPI supply pin at 1.7 to 3.6 V lets the part talk to a low voltage controller without a translator, and the analogue multiplexer means one ADC channel for the thermistor and the internal nodes. Those two features reduce the controller side of the board, and they are the reason a projector built around this family can use a small controller with few pins.

What the documents do not publish

The page gives the current ceiling and the block list but no switching frequency, no inductor value and no sense resistor value for the external stage, so a board cannot be costed from the page. It gives no efficiency curve, which is what the thermal calculation needs, and no gate drive strength for the external transistors, which is what the transistor choice depends on. All of those are in the application section of the document.

The page also does not print the register map, so the start up state of the LED current, the strobe decoder and the protection masks has to be read from section seven. A board that comes up with the LED current register at its default will flash at a level nobody chose, and that is a symptom that looks like a software fault and is a register default.

Second source and long term availability

There is no second source for a part tied to a specific display controller and mirror, and the C suffix lifebuy shows how quickly a member of this family can be withdrawn. The last time buy and lifetime buy planning page sets out how we plan a bridge buy, and the component obsolescence management page covers the ongoing monitoring.

A programme that is still shipping a C suffix board should be treating the D suffix as the only long term option and checking whether the board and the optical engine accept it. The two are the same pin count and the same footprint, and the difference is in the silicon revision and in what the vendor will quote. That is a question for the vendor's own field team before it is a purchasing question.

What to send with an enquiry

Send the exact string, the packing you need, the quantity and the date. State the LED current per channel, the number of channels and whether the strings are series or parallel, because the series option is a silicon revision difference rather than a register setting. State the heatsink arrangement, since the quoted thermal resistance assumes a fan and a fin stack.

Say which silicon suffix the existing board was qualified on. A C suffix board that needs a D suffix part is a re-qualification, not a swap, and the schedule should reflect that. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.