Contact Us

DAC8760IPWPR

Brand: Texas Instruments
Texas Instruments DAC8760IPWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DAC8760IPWPR — Power Management & Signal Chain | Superb Automation

DAC8760IPWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DAC8760IPWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DAC8760IPWPR: the 16-bit member of the 4-20 mA transmitter pair

The DAC8760IPWPR is the 16 bit member of the DACx760 pair, a single channel converter that drives a current loop and a voltage output from one die in a 24 pin HTSSOP, packed 2000 pieces on a large tape and reel. The vendor carries the family as ACTIVE and lists current ranges of 4 to 20 mA, 0 to 20 mA and 0 to 24 mA, voltage ranges of 0 to 5 V and 0 to 10 V with a 10 per cent overrange, simultaneous current and voltage output from one register, 0.1 per cent of full scale total unadjusted error maximum, an internal 5 V reference at 10 parts per million per degree, a CRC check and watchdog, a thermal alarm, an open circuit alarm and a short circuit limit over minus 40 to plus 125 degrees.

The difference from the 12 bit twin is resolution and nothing else that a purchase order can see. Both parts share the 24 pin HTSSOP and the 40 pin VQFN, both share the register map, and both are level 3 at 260 degrees with a 168 hour floor life. A programme that moves from the 12 bit to the 16 bit part does not change the board, and that is the reason the pair exists rather than a single part number with an option code.

The DAC8760IPWPR rows as the addendum publishes them

Part classSingle channel 16 bit current and voltage output converter
Vendor statusACTIVE, production data
Data sheetSBAS528D, June 2013, revised December 2021
Resolution16 bits
Current ranges4 to 20 mA, 0 to 20 mA, 0 to 24 mA
Voltage ranges0 to 5 V, 0 to 10 V, with 10 per cent overrange
Total unadjusted error, voltage0.1 per cent of full scale maximum
Total unadjusted error, current0.2 per cent of full scale over temperature
Differential nonlinearity1 LSB maximum, monotonic
Integral nonlinearity, voltage0.04 per cent of full scale over temperature
Integral nonlinearity, current0.08 per cent of full scale over temperature
Internal reference5 V, 10 parts per million per degree maximum
Reference input window4.95 V to 5.05 V external
Loop complianceSupply minus 2 V at 24 mA
Settling, current10 microseconds for a 16 mA step, 25 with 1 mH of inductance
Settling, voltage22 microseconds for 0 to 10 V, 13 for 0 to 5 V
Slew rate0.5 volts per microsecond, register programmable
Output headroom0.5 V above and below the swing
Voltage load1 kilohm for specified performance
Capacitive load5 nanofarad at 1 kilohm, 1 microfarad with a 4 nanofarad compensation capacitor
Short circuit current30 mA
Body, HTSSOP24 pins, 7.80 by 4.40 millimetres
Body, VQFN40 pins, 6.00 by 6.00 millimetres
Reel row, HTSSOPDAC8760IPWPR, 2000 pieces, large tape and reel
Reel row, VQFNDAC8760IRHAR, 2500 pieces, large tape and reel
Small reel, VQFNDAC8760IRHAT, 250 pieces
Moisture levelLevel 3 at 260 degrees, 168 hour floor life

The current settling figure has a second row that the 12 bit page does not carry in the same place: 25 microseconds when the loop has 1 millihenry of inductance. A 4 to 20 mA loop in a plant with long cable and an input filter is an inductive load, so the 10 microsecond figure applies to a bench resistor and the 25 microsecond figure applies to the field. A customer who sizes a control loop against 10 microseconds and commissions into 1 millihenry will find the loop is slower than the calculation.

What the electrical table fixes

Sixteen bits on a 20 mA range is a step of 305 nanoamps, and the current output total unadjusted error is 0.2 per cent of full scale over temperature, which is 40 microamps. The error is therefore 131 times the resolution, and a customer who asks for 16 bit accuracy on a current loop is asking for something the loop cannot deliver without calibration. This is the number to quote when a specification arrives with a resolution requirement written as an accuracy requirement.

The voltage output is the better of the two, 0.1 per cent of full scale over temperature, and it drives a 1 kilohm load to the specified performance. The headroom and footroom rows, 0.5 V at each end, mean a 10 V output needs an 11 V supply at least, and the overrange mode pushes that to 11 V of output against a supply the same 0.5 V higher. The capacitive load row is generous, 1 microfarad with a 4 nanofarad compensation capacitor, and that is what lets the part drive a cable without an external buffer.

The internal reference and the internal 4.6 V supply are the two blocks that decide the support circuit. Using the internal reference saves a component but ties the absolute accuracy to the reference drift, 10 parts per million per degree, which over 145 degrees is 0.145 per cent and larger than the converter linearity. Using an external reference moves the problem to the reference and keeps the converter inside its own error budget, and the reference input window of plus or minus 50 mV around 5 V is narrow enough that only a trimmed source fits.

Where the body fits on a board

The 24 pin HTSSOP carries a thermal pad and is the body that a transmitter module will use, because the loop current passes through the die and the pad is the path out. The 40 pin VQFN is smaller and needs the pad soldered to a plane with vias, which is a reflow only proposition. Both are level 3, so both need a bake or a dry pack discipline on a board that sits out of the bag for more than 168 hours.

The alarm and watchdog pins are the reason this part exists in a safety adjacent product. A watchdog that has to be refreshed by the controller and a CRC that has to match on every frame are two independent checks, and a board that does not route the alarm pin to the controller has bought a part whose failure mode is silent. The vendor recommends a 100 picofarad capacitor to ground on the comparator pin, which is the one external component that the function needs and that is easy to omit.

What the documents do not publish

The page gives total unadjusted error at three temperatures and no histogram of that error across a production lot, which is what a six sigma calculation would need. It gives no output noise density and no crosstalk figure, and it gives no lifetime drift for the current output beyond a drift against time row for the voltage output at 125 degrees over 1000 hours. A transmitter specified for ten years of drift needs the long term data from the vendor rather than a typical curve.

The register map is not on the product page, so the power up state of the alarm mask and the watchdog timer has to be read from section eight. That matters because a watchdog that starts enabled and is refreshed by nobody will trip a fault on every cold start, and the symptom looks like a board fault rather than a register default.

Second source and long term availability

The class of integrated 4 to 20 mA transmitters is narrow and the crosses differ in compliance voltage, HART coupling and register map, so a cross is usually a board change rather than a part change. The ADC DAC cross reference page sets out what we compare, and the obsolete part cross reference hub page covers parts that have left the catalogue.

Both bodies carry live rows at 2000 and 2500 pieces, and the small reel at 250 pieces is the packing a prototype receives. The status is a vendor statement and not a commitment, so a programme that needs ten years should ask for a written availability statement, and should ask which body the vendor intends to keep.

What to send with an enquiry

Send the exact string, the body, the quantity and the date you need it. State the loop supply, the loop resistance and the cable inductance if it is known, because the settling figure changes with it. State whether the internal reference is used or an external 5 V source, since the reference input window is plus or minus 50 mV.

Say whether the alarm and watchdog pins are routed, because a part ordered for a transmitter module and a part ordered for a bench board carry the same string and very different support expectations. The BOM scrubbing page explains how we reconcile a line like this against a build quantity before a schedule is confirmed.