CD74HC4053PWR
Product Specifications
CD74HC4053PWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD74HC4053PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD74HC4053PWR: triple two-channel analogue switch with a separate negative rail
CD74HC4053PWR is the switch for differential signals and for routing that needs three independent changeover contacts in a TSSOP body of 16 pins. The part contains three single pole double throw analogue switches, each with its own select line and a common inhibit, in a 16-pin body. On resistance is 70 ohms typical at a 4.5 V total supply, the signal path is bidirectional, and a separate negative rail lets signals swing below ground. The control side runs from 2 V to 6 V.
Order code and package
| Order code | CD74HC4053PWR |
| Function | triple single pole double throw analogue switch |
| Select lines | one per switch, plus a common inhibit |
| On resistance | 70 ohms typical at a 4.5 V total supply |
| Signal path | bidirectional, changeover contacts |
| Switch voltage | 0 to 10 V with a separate negative rail |
| Supply | 2 to 6 V on the control side |
| Package | TSSOP, 16 pins, 5.00 mm by 4.40 mm |
| Temperature range | minus 40 to plus 125 C |
| Switching | break before make on each contact |
| Datasheet | SCHS123 revision J |
| Family | same die family as the 8-channel and 4-channel members |
Electrical parameters that decide the application
| Configuration | three changeover switches, which is what a differential pair plus a spare needs |
| On resistance | 70 ohms typical at 4.5 V, 40 ohms at 9 V |
| Matching | the three switches sit on one die, so their resistances track with temperature |
| Break before make | prevents a momentary short between the two throws during a change |
| Inhibit | opens all three switches at once, which is the state a fault handler wants |
| Negative rail | VEE allows bipolar signals through the switch |
| Control levels | 30 and 70 percent of the control supply |
| Charge injection | a step on a high impedance node at every change, so the settling time has to include it |
| Package | TSSOP 16 in a 5.00 mm body |
| Crosstalk | channel to channel isolation specified in the same table as the on resistance |
Points to check before this part goes on a BOM
Three changeover switches is a different function from the 8-channel multiplexer, and the two are not interchangeable on a board. A differential pair switched at both ends needs two contacts and the third is the spare that makes this body worth its pin count.
The three switches share one die, so their on resistances track over temperature. That tracking is what keeps a differential pair balanced when the board warms up, and it is worth more than a lower absolute resistance on a stage that measures a ratio.
Break before make applies to each contact, not between contacts. Two of the three switches can be in different positions at the same instant, so a circuit that relies on all three changing together needs the address lines driven from one register and the propagation delays checked.
Charge injection into a high impedance node is the same problem as on the 8-channel part, and it is worse here when the spare contact switches an unloaded node. A 10 pF sample capacitor sees millivolts of step, and the converter's acquisition time has to absorb it.
The 4.5 V on resistance figure assumes VEE takes part of the total. With VEE at ground and a 3.3 V control supply, the total is 3.3 V and the resistance is higher, so a board that quotes 70 ohms has quoted a different operating point.
The control thresholds are 30 and 70 percent of the control supply, so a 3.3 V controller cannot guarantee a high level into a 5 V supplied switch. The select and inhibit lines are where that shows up, and a level translator on three lines is cheaper than a re-spin.
Where this order code fits
Boards switching a differential pair usually take this part, while boards scanning many single ended channels take the 8-channel member of the family. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
How many switches does the part contain? Three single pole double throw switches, each with its own select line and a common inhibit.
Do the three switches change at exactly the same time? They are controlled separately, so the change is simultaneous only as far as the drive and the propagation delays make it so; break before make applies per contact.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.