Contact Us

CD74HC4051M96

Brand: Texas Instruments
Texas Instruments CD74HC4051M96 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD74HC4051M96 — Power Management & Signal Chain | Superb Automation

CD74HC4051M96

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD74HC4051M96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD74HC4051M96: 8-channel analogue multiplexer with logic level conversion

CD74HC4051M96 is the switch that routes eight analogue channels into one converter input in a SOIC body of 16 pins. The part is an eight-channel analogue multiplexer and demultiplexer with a bidirectional signal path, on resistance of 70 ohms typical at a 4.5 V total supply and 40 ohms at 9 V, break before make switching and an inhibit input that opens all channels. It runs from 2 V to 6 V on the control side with a separate negative rail for signals that swing below ground.

Order code and package

Order codeCD74HC4051M96
Function8-channel analogue multiplexer and demultiplexer
Controlthree address lines plus an inhibit input
On resistance70 ohms typical at a 4.5 V total supply, 40 ohms at 9 V
Signal pathbidirectional, so any input can be an output
Switch voltage0 to 10 V, with a separate negative rail for signals below ground
Supply2 to 6 V on the control side
PackageSOIC, 16 pins, 9.90 mm by 3.91 mm
Temperature rangeminus 40 to plus 125 C
Switchingbreak before make, so two channels are never connected at once
DatasheetSCHS122 revision J
Crosstalklow between channels, specified with the isolation in the same table

Electrical parameters that decide the application

On resistance70 ohms typical at 4.5 V, which with a 10 kohm load is 0.7 percent of gain error
On resistance flatnessthe variation across the signal range is what produces distortion, not the absolute value
Leakagepicoamp class when the channel is off, which is why the part works in front of a high impedance converter
Break before makeprevents two sources from being shorted together during a channel change
Address linesthree lines select eight channels, and the inhibit pin opens all of them
Negative railVEE lets the switch pass signals below ground, which a single supply CMOS switch cannot
Control levelsHC thresholds are 30 percent and 70 percent of the supply, so a 5 V control is needed for 5 V logic
Charge injectionmoves a small packet of charge into the load when the channel changes, which shows as a step on a high impedance node
PackageSOIC 16, with TSSOP and PDIP bodies in the family
Settlingset by the source impedance and the load capacitance rather than by the switch alone

Points to check before this part goes on a BOM

Seventy ohms of on resistance in series with a converter input is a gain error that changes with the signal, because the resistance is not flat across the range. The absolute value is a divider term; the flatness is the distortion term, and the flatness figure is the one to check for an audio or a sensor path.

Break before make is the feature that stops two channels being shorted when the address changes. Without it, switching from a 5 V source to a ground referenced one dumps current through both switches for the duration of the overlap.

Charge injection puts a step on a high impedance node every time the channel changes. Into a 10 pF converter sample capacitor the step is millivolts, and the settle time before the conversion has to account for it rather than assuming the switch is transparent.

The 4.5 V on resistance figure belongs to a total supply of 4.5 V, which includes VEE. A board running the control side at 3.3 V with VEE at ground has a 3.3 V total and a resistance well above 70 ohms, so the figure in the feature list does not apply.

VEE is what allows a signal that swings below ground to pass without clipping. Tying VEE to ground turns the part into a unipolar switch, which is fine for a 0 to 3 V sensor and wrong for a bipolar audio or instrumentation signal.

The control thresholds are 30 and 70 percent of the supply, so a 3.3 V controller driving a 5 V supplied switch only reaches 66 percent and sits below the guaranteed high level. The logic supply and the controller have to match, or a level translator is needed on the three address lines.

Where this order code fits

Boards routing several sensors into one converter usually pair this switch with a converter that has a sample and hold, so the charge injection has somewhere to settle. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can the switch pass signals below ground? Only with a negative rail on VEE. With VEE at ground the switch is unipolar and clips at zero.

Why does on resistance matter if the load is high impedance? Because it is in series with the source, so it forms a divider whose ratio changes with signal level; that variation is the distortion term.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.