CD4541BM96
Product Specifications
CD4541BM96
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4541BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4541BM96: the programmable timer on a 2500 piece SOIC reel
The CD4541BM96 is the large tape and reel entry for the CD4541B, a programmable timer built from a 16-stage binary counter, an RC oscillator, an automatic power on reset circuit and output control logic, in a 14-lead small outline body. The vendor page lists the device as ACTIVE with one bit, an operating range of minus 55 to plus 125 degrees and a package list of four bodies. The reel row is 2500 pieces, level 1 at 260 degrees, nickel palladium gold finish, and the marking on the body is CD4541BM rather than the orderable string.
The part replaces a counter chain and an oscillator with one package and two external resistors plus one capacitor. The counter divides the oscillator by a selected power of two, the stage is chosen with the two time select inputs, and the output can be a continuous square wave or a single transition after a reset. That single transition mode is what makes the part a timer rather than a divider, and it is the mode most boards use.
The CD4541B rows as the addendum publishes them
| Part class | Programmable timer, 16-stage counter with RC oscillator |
| Vendor descriptor | Programmable timer, 1 bit, 3 V to 18 V |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS097 or later revision, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| Supply range | 3 V to 18 V, 20 V type rating in the headline |
| Oscillator, RC mode | 1 kHz to 100 kHz per the data sheet text |
| Oscillator, external clock | DC to 100 kHz applied to pin 3 |
| Divider stages | 8, 10, 13 or 16, selected by the two time select inputs |
| Output modes | Continuous square wave, or single transition after reset |
| Output polarity | Q or Q bar, selected at the output control input |
| Reset | Automatic power on reset, or master reset input |
| Output resistance | About 100 ohm at 15 V, symmetrical |
| Load drive | Six low power TTL loads over the rated temperature range |
| SOIC body | 14 leads, 51.9 square millimetres, 8.65 by 6 mm |
| SOIC tube row | CD4541BM, 50 pieces, Active |
| SOIC reel row | CD4541BM96, 2500 pieces, Active |
| SOIC small reel | CD4541BMT, 250 pieces, Active |
| SOP reel row | CD4541BNSR, 2000 pieces, Active |
| TSSOP rows | CD4541BPW tube 90 pieces, BPWR reel 2000 pieces, Active |
| PDIP row | CD4541BE, 25 pieces in a tube, Active |
| Ceramic rows | CD4541BF and CD4541BF3A, 25 pieces, Active |
Every body is live and the SOIC alone offers three pack sizes, which is the widest choice in this band. A pilot build can take the 50 piece tube, a small build the 250 piece reel and a production run the 2500 piece reel, without a footprint change. The SOP and the TSSOP exist for boards that need a smaller area, and the plastic DIP remains for a socketed instrument.
What the timer actually does
The counter increments on positive clock edges and can be cleared by the master reset input. The output is taken from the eighth, tenth, thirteenth or sixteenth stage, chosen by the two time select inputs. In the continuous mode the output is a square wave at the oscillator frequency divided by two to the power of the selected stage, so the same RC network can produce four different frequencies without a change. In the single transition mode, after a master reset, the output changes once after two to the power of the stage minus one counts and stays there until another reset or a mode change.
The automatic reset is set by tying pin 5 low before power is applied. The vendor warns that the automatic reset circuit draws an appreciable current and should not be used when low power matters, and that a reliable automatic power on reset needs a supply above 5 V. A board that runs at 3 V and needs a guaranteed start state therefore has to drive the master reset from a supervisor rather than rely on the internal circuit.
The oscillator runs from one resistor and one capacitor, with a second resistor in series, and the vendor prints the network and the frequency range. The RC mode is specified from 1 kHz to 100 kHz, and the external clock mode accepts DC to 100 kHz on pin 3. A board that needs a longer delay uses a larger divider stage rather than a slower oscillator, because the leakage of a large capacitor makes a very low frequency unreliable.
Where the SOIC reel is the right format
The SOIC is 51.9 square millimetres against 181.42 for the plastic DIP and 32 for the TSSOP. It is the body that sits between the two: small enough for a dense board and coarse enough for a 1.27 mm stencil. The 2500 piece reel covers a build of a thousand boards with two timers each, and the 50 piece tube covers a prototype without opening a reel.
The thermal impedance of the SOIC in the family document is 86 degrees per watt, against 80 for the plastic DIP and 113 for the TSSOP. The timer draws little current and drives light loads, so the number is not a constraint in normal use. It becomes relevant when the output drives a transistor base continuously, which is the case where the TSSOP reaches its limit first.
The long delay case is where the timer is most often misapplied. A one hour delay from a 16 stage divider needs an oscillator of about 4.5 Hz if the last stage is used, and at that frequency the capacitor and the resistor are large enough that leakage becomes part of the timing. The vendor caps the RC mode at 100 kHz at the top and does not state a floor in the product page, while the data sheet text describes the RC mode from 1 kHz, which is the range where the network behaves predictably. A board that needs minutes or hours should divide a faster oscillator with an external counter rather than slow the RC network down.
The output polarity control is the second detail that catches a board. The Q or Q bar selection changes the sense of the single transition, and a circuit that expects the output to go high after the delay will go low if the control pin is tied the other way. The vendor describes the control as an output logic level flexibility feature, which is accurate and does not tell a reader which way to tie it.
What the documents do not publish
The page does not print the oscillator formula, the frequency tolerance over temperature or the reset current. Those are in the data sheet, and the tolerance is what decides whether the timer can be used without a trim. The page also does not print the timing diagram for the single transition mode, which is the mode that most customers ask about and the one where a wrong stage selection produces a delay that is off by a factor of four.
Second source and long term availability
The CD4541B is second sourced under the same number and every body is active. The nearest alternative is a small microcontroller with an internal oscillator, which changes the part count, the current and the code entirely. For a board that has no code and needs a fixed delay, the timer remains the cheaper route. The obsolete part cross reference hub covers the equivalence checks, and the pin to pin cross reference page covers the package checks.
What to send with an enquiry
Send the string, the body, the delay you need and the supply rail. The delay and the rail together decide the stage and the RC values, and the rail decides whether the automatic reset can be trusted. If the board is surface mount, say which reel size the line can take, because three live SOIC pack sizes are available and the choice is a line decision. The kitting service page explains how the timer, its resistors and its capacitor are picked as one kit.