CD4082BE
Product Specifications
CD4082BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4082BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4082BE: the dual four input AND gate in the 14-lead plastic DIP
The CD4082BE is the plastic dual in line entry for the CD4082B, two independent four input AND gates in a 14-lead body. The vendor page lists the device as ACTIVE with the descriptor 2-ch, 4-input, 3-V to 18-V AND gates, a drive of 6.8 mA in both directions, an 8 Mbps data rate and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4082BE.
Two four input AND gates in fourteen leads is the widest AND function in the family, and it is the shape a board takes when an enable has to be qualified by four conditions at once. The same document carries the CD4073B triple three input AND and the CD4081B quad two input AND, so the three shapes share a data sheet and an addendum and differ only in how the pins are grouped. A buyer who needs nine inputs in total has to decide between three packages of three inputs and two packages of four plus a spare.
The CD4082B rows as the addendum publishes them
| Part class | Two independent four input AND gates |
| Vendor descriptor | 2-ch, 4-input, 3-V to 18-V AND gates |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS054 family document, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| Supply range | 3 V to 18 V, 20 V type rating in the headline |
| Output drive | 6.8 mA sink and source at 15 V |
| Data rate | 8 Mbps in the parametric table |
| Propagation delay | 60 ns typical at 10 V into 50 pF |
| Input thresholds at 5 V | Low 1.5 V maximum, high 3.5 V minimum |
| Input thresholds at 10 V | Low 3 V maximum, high 7 V minimum |
| Input current | 1 microamp at 18 V over temperature, 100 nA at 25 degrees |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| PDIP body | 14 leads, 181.42 square millimetres, 19.3 by 9.4 mm |
| PDIP rows | CD4082BE and CD4082BEE4, 25 pieces, Active |
| SOIC tube row | CD4082BM, 50 pieces, Active |
| SOIC small reel | CD4082BMT, 250 pieces, Active |
| SOIC large reel | CD4082BM96, 2500 pieces, Active |
| SOP reel row | CD4082BNSR, 2000 pieces, Active |
| TSSOP rows | CD4082BPW tube 90 pieces, BPWR reel 2000 pieces, Active |
| Ceramic rows | CD4082BF and CD4082BF3A, 25 pieces, Active |
| Military marking | 7705902CA on the F3A row |
Every row in that table is active, which is not the pattern across the band. The CD4073B triple gate next door has an obsolete tube and an obsolete small reel, and the CD4081B quad gate is fully active. A consolidated order that treats the three AND functions as one line item will therefore produce a mix of live and dead rows, and the dead rows will only appear at the point of order confirmation unless the addendum is read first.
What the parametric table fixes
The two gates are specified over 3 to 18 V with parametric ratings at 5, 10 and 15 V. The input thresholds at 5 V are 1.5 V maximum low and 3.5 V minimum high, at 10 V they move to 3 V and 7 V, and at 15 V to 4 V and 11 V. A four input gate multiplies the leakage that has to be supplied by the driving stage, and the 1 microamp input current at 18 V is a per input figure, so four inputs contribute four microamps to the node.
Drive is 6.8 mA at 15 V and the typical propagation is 60 ns at 10 V into 50 pF. The four inputs add capacitance rather than delay, so the gate itself does not become slower, but the stage that drives it sees four times the load. On a board with a wide enable tree built from these gates, the second stage is usually the one that misses timing, not the last.
The 8 Mbps data rate in the parametric table is a family descriptor and the 60 ns typical is the real delay. At 5 V the guaranteed sink current falls to about 1 mA, which is enough for a CMOS input and not enough for an opto coupler or a bipolar base without a resistor. The page prints both the drive and the delay and leaves the reader to check the rail.
Where the wide AND function fits
A four input AND is an interlock in one package. Four conditions, all of which must be true before an output is allowed, is exactly what a power supply sequence, a radio transmit permit or a door interlock needs. Splitting that into two input gates costs two packages and adds a stage of delay, and the added stage is often the one that races with the condition that just changed.
The plastic DIP is 181.42 square millimetres and the SOIC is 51.9, so the surface mount body is a third of the area. The thermal impedance is 80 degrees per watt in the DIP, 86 in the SOIC, 76 in the SOP and 113 in the TSSOP. With a quiescent current measured in microamps the thermal figures only matter in a fault, and the DIP has the most margin because it has the most lead frame area.
What the documents do not publish
The page has no maximum propagation delay, no output capacitance and no short circuit rating. The truth table and the switching table at three rails are in the data sheet. The page also does not print the pin out, and for a fourteen lead package with eight inputs the pin out is the first thing an assembly drawing needs. That has to come from the data sheet or from the package drawing in the same document set.
The addendum also carries paired rows that share a marking, such as CD4082BE and CD4082BE.A, and a buyer who needs one specific row for an approved vendor list has to name it. The two rows are separate orderable entries with the same body, the same finish and the same marking, and a distributor will ship whichever the system selects. That is harmless for a new build and it is not harmless for a customer who has to keep a documented part number on a drawing for a decade.
The fourteen lead package is wide enough for the eight inputs to sit on one side and the two outputs on the other, which keeps a wide interlock tree on a single routing layer. A board that has to cross signals has to route around the package, and a part that needs two layers to escape costs more than the difference in unit price, especially on a board that is already tight for routing and cannot afford a third copper layer.
Second source and long term availability
The CD4082B is second sourced under the same number and the pin out has been stable for decades. The functional alternative is a 74HC21, which is a dual four input AND in a different pin out, so it is a board change rather than a substitution. The obsolete part cross reference hub collects the equivalence checks, and the incoming inspection plan page covers what to test when a second source is first received.
What to send with an enquiry
Send the string, the body, the quantity and the date. If the interlock is safety related, say so, because that changes the inspection and the traceability requirements rather than the part. If the board is surface mount, the 2500 piece reel and the 250 piece small reel are both live and the choice depends on the build size rather than on availability. The BOM scrubbing page explains how those pack sizes are reconciled before a schedule is promised.