Contact Us

CD4071BE

Brand: Texas Instruments
Texas Instruments CD4071BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4071BE — Power Management & Signal Chain | Superb Automation

CD4071BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4071BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4071BE: the quad two input OR gate in the 14-lead plastic DIP

The CD4071BE is the plastic dual in line entry for the CD4071B, four independent two input OR gates in a 14-lead body. The vendor page lists the device as ACTIVE with the descriptor 4-ch, 2-input, 3-V to 18-V OR gates, a drive of 6.8 mA in both directions, an 8 Mbps data rate and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces, the lead finish is nickel palladium gold, and the marking is CD4071BE.

This is the body that still makes sense on a through hole line, in a repair shop, or on a board where the socket is already there. The same die is available in four surface mount formats, and the orderable status is not the same across them: the SOIC reel and the SOP reel are active, the TSSOP reel carries the NRND lifecycle code, and the ceramic side is split between an active F3A row and a non recommended F row. That split is the reason this page starts with the addendum rather than with the function.

The CD4071B rows as the addendum publishes them

Part classFour independent two input OR gates
Vendor descriptor4-ch, 2-input, 3-V to 18-V OR gates
Vendor statusACTIVE, catalogue rating
Data sheetSCHS054 family document, acquired from Harris Semiconductor
Package addendum date18 September 2026
Supply range3 V to 18 V, 20 V type rating in the headline
Output drive6.8 mA sink and source at 15 V
Data rate8 Mbps in the parametric table
Propagation delay60 ns typical at 10 V
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
PDIP body14 leads, 181.42 square millimetres, 19.3 by 9.4 mm
PDIP rowsCD4071BE, CD4071BE.A and CD4071BEE4, 25 pieces each, Active
SOIC tube rowCD4071BM, Obsolete, blank quantity, Call TI
SOIC reel rowCD4071BM96, 2500 pieces, Active
Other SOIC rowCD4071BMT, Obsolete
SOP reel rowCD4071BNSR, 2000 pieces, Active
TSSOP reel rowCD4071BPWR, 2000 pieces, NRND
TSSOP tube rowCD4071BPW, Obsolete
Ceramic rowsCD4071BF NRND, CD4071BF3A Active at 25 pieces
Military row7706002CA, ceramic, 25 pieces, Active

The TSSOP row is the one to read twice. It is a live reel at 2000 pieces with a full quantity and a real lead finish, and it carries the NRND lifecycle flag. That is a vendor lifecycle statement and not a stock statement: the parts exist, a distributor can ship them, and a new board that puts this row on a bill of materials is starting on a body the vendor has already flagged. The SOIC reel and the SOP reel are the two surface mount rows without that flag.

What the parametric table fixes

The four gates are specified over 3 to 18 V with parametric ratings at 5, 10 and 15 V, a drive of 6.8 mA at 15 V, and a typical propagation of 60 ns at 10 V. The 8 Mbps data rate in the table is a derived figure, not a measured eye diagram, and a chain of OR gates in series will not reach it because each stage adds its own delay. On a 5 V rail the drive falls to about 1 mA at the guaranteed sink current, which is the number that matters when the gate drives a bipolar transistor base or an opto coupler input.

The noise margin is 1 V at 5 V, 2 V at 10 V and 2.5 V at 15 V over the full package temperature range, and the input current is 1 microamp at 18 V, falling to 100 nA at 25 degrees. Those two figures together decide how much series resistance a customer can put in front of an input for protection. A 100 k resistor with a microamp of input current drops a tenth of a volt, which is fine at 15 V and marginal at 5 V, and the page states the arithmetic rather than leaving it to the bench.

One limit is not on the product page at all: the 20 V headline is a type rating, the parametric table stops at 15 V, and the absolute maximum supply is 20.5 V. A board that runs at 18 V has DC limits but no guaranteed switching limit, and a board that runs at 20 V is outside the recommended range even though the headline suggests otherwise.

Where the plastic DIP is the right choice

At 181.42 square millimetres the plastic DIP is three and a half times the area of the SOIC and more than five times the TSSOP, so it is never the choice for a dense board. It is the choice when the board is single sided, when the assembly house runs a wave solder line, when the part has to be socketed for a test fixture, or when the board is old enough that the footprint is fixed and a re-spin is not on the table. The 25 piece tube suits a repair kit and a pilot build and it is a poor format for a pick and place line, which is why the tube rows in this family are the ones that keep closing.

The thermal impedance of the plastic DIP in the family document is 80 degrees per watt junction to ambient, the lowest of the four plastic bodies and better than the 86 of the SOIC and the 113 of the TSSOP. At a quiescent current measured in microamps that number is academic, and it stops being academic when an output is loaded heavily in a fault. The wider body spreads the heat over a larger lead frame, which is why the DIP survives a bench accident that a TSSOP does not.

What the documents do not publish

The parasitic figures that a fast board needs are not on the page either. Input capacitance is in the data sheet table, output capacitance is not printed at all, and the switching time is quoted into a 50 pF load with no derating curve for a heavier one. A board with a 200 pF trace load therefore has a delay the page cannot predict, and the bench has to measure it.

The page gives no maximum propagation delay, no output capacitance, no short circuit current and no latch up rating. The truth table, the switching table at three rails and the test circuit are in the data sheet, which for this family is a text document, so the numbers are readable, but they are not reproduced on the page. The page also does not print the package drawing, and a customer who needs the lead bend radius for a socket has to go to the mechanical section.

Second source and long term availability

The CD4071B is second sourced under the same number by more than one vendor and the pin out is a de facto standard. The substitution that causes trouble is a move to a 74HC32, which is faster and has a different input threshold, so a circuit that relied on the slow 60 ns edge for timing will change behaviour. The pin to pin cross reference page shows the checks, and the component obsolescence management page covers the case where only the tube rows close.

What to send with an enquiry

Send the string, the body, the quantity and the date. If the board is through hole, confirm the tube pack of 25 pieces, because a 500 piece build needs twenty tubes and that is a booking rather than an off the shelf line. If the board is surface mount, say whether the TSSOP is acceptable, since that row is still shipping but carries a lifecycle flag. The last time buy and LTB planning page explains how a final order is sized when a body is closing.