Contact Us

TPS65218D0RSLR

Brand: Texas Instruments
Texas Instruments TPS65218D0RSLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65218D0RSLR — Power Management & Signal Chain | Superb Automation

TPS65218D0RSLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65218D0RSLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65218D0RSLR: a four rail PMIC for Cortex-A8 and A9 systems in the 6 mm VQFN

TPS65218D0RSLR is a power management IC with three bucks, a buck boost, two backup rails and a load switch set in a VQFN (RSL) body of 48 pins. The RSL body is 6.00 mm by 6.00 mm with forty eight pins, and the D0 in the string is the silicon revision rather than a package code: the revision register at subaddress 5h reads 4.0 for D0. The document is SLDS206E, revised February 2021, and its first page still describes the family by rail rather than by revision.

Order code and package

TPS65218D0RSLRVQFN (RSL), 48 pins, 6.00 mm by 6.00 mm; the revision register 5h reads 4.0 for the D0 revision
Addendum rowsthe published rows in SLDS206E are the B1 strings, TPS65218B1RSLR at 2500 pieces on a large reel and TPS65218B1RSLT at 250 on a small reel, every one of them marked NRND
HTQFP alternativethe same die in the 48 pin PHP body at 7.00 mm by 7.00 mm, 1000 pieces on a large reel for the B101 and B1 strings
Finish and moistureNIPDAU lead finish, MSL level 3 at 260 C with a 168 hour floor life, -40 to 105 C operating range
Supervisorbuilt in monitors on DCDC1 and DCDC2 at plus or minus 4 percent and on DCDC3, DCDC4 and LDO1 at plus or minus 5 percent
InterfaceI2C slave at address 0x24, data rates to 400 kbps, with a separate power good output for the backup domain

Electrical parameters that decide the application

DCDC1 and DCDC21.8 A each from a 2.7 V to 5.5 V input, 1.1 V default, adjustable from 0.85 V to 1.675 V, 100 percent duty for lowest dropout
DCDC31.8 A from the same input, 1.2 V default, adjustable from 0.9 V to 3.4 V
DCDC4buck boost, 1.6 A, 3.3 V default, adjustable from 1.175 V to 3.4 V, which is the rail that holds up when the input crosses the output
DCDC5 and DCDC61 V and 1.8 V fixed, fed from the system supply or from a coin cell on the CC pin, with an IN_nCC flag that reports which source is in use
LDO1400 mA from 1.8 V to 5.5 V in, 1.8 V default, adjustable 0.9 V to 3.4 V, dropout 400 mV maximum at 2.7 V in
Load switchesLS1 350 mA from 1.2 V to 3.6 V with 110 mOhm at 1.35 V; LS2 100 mA or 500 mA selectable from 4 V to 5.5 V with 500 mOhm; LS3 the same current options at the higher voltage
Switching frequency2400 kHz on the integrated bucks, which is what keeps the inductors small in a 6 mm package footprint
Sequencingrail order and timing are set through I2C registers rather than by external components, and the settings live in OTP
Protectionundervoltage lockout per rail, overtemperature warning ahead of shutdown, and active output discharge when a rail is disabled
Always ona push button monitor that stays alive on the backup domain, which is why the coin cell path exists at all

Family variants and how they differ

TPS65218B1the earlier revision, published in the addendum as NRND, so a board that was qualified on B1 and needs D0 has to confirm the register map differences rather than assume they are identical
TPS6521815 and TPS6521835OTP images of the same die with different default rail voltages and sequencing, selected by the first register
RSL against PHP6 mm VQFN against 7 mm HTQFP, same 48 pins of function, different thermal path and different reel sizes
Against a discrete setfour bucks, an LDO, three load switches and a supervisor in one body against the same functions as separate parts
No boost for the main railsDCDC4 is the only rail that can run above its input, and it is limited to 1.6 A

Points to check before this part goes on a BOM

The order code needs a check before anything else, because SLDS206E publishes B1 rows only and marks every one of them NRND. The D0 revision appears in the document as a value in the revision register, not as an orderable row, so a buyer holding a TPS65218D0RSLR requirement is asking for a revision whose reel quantity and lifecycle status are not printed in this revision of the document. That is worth settling with the vendor or with a date coded stock check rather than assuming 2500 pieces from the B1 row.

The rail budget is fixed by the silicon, so the useful question is which rails a given system actually loads. DCDC1 and DCDC2 at 1.8 A each normally feed the core and the MPU domain, DCDC3 at 1.8 A feeds DDR or a 1.2 V peripheral domain, and DCDC4 at 1.6 A is the one that has to survive an input that crosses its output, which is why it is a buck boost and not a fourth buck.

DCDC5 and DCDC6 are the reason this part shows up in battery products. They run from either the system rail or a coin cell on the CC pin, and the IN_nCC flag tells the processor which one is live so the software can decide whether to keep the real time clock running or start a controlled shutdown. That behaviour is inside the part, so it does not depend on the processor staying awake.

Everything programmable is programmed over I2C at 0x24 and then stored, which means an unprogrammed part comes up on its OTP defaults. A board that expects 1.8 V on LDO1 and gets the 1.8 V default is fine, but a board that reorders the rails has to have the sequencing written before the processor is released from reset, otherwise the first boot and every later boot behave differently.

What the load switch set is for

LS1 is a 350 mA switch with 110 mOhm at 1.35 V, and LS2 and LS3 offer 100 mA or 500 mA at 5 V with 500 mOhm. In practice LS1 powers a low voltage peripheral domain such as an SD card or a sensor hub, and LS2 and LS3 switch USB or HDMI 5 V branches. All three are controlled through registers, so a rail can be dropped in software without a GPIO.

The current limit is selectable on LS2 and LS3 and fixed on LS1, which is the detail that decides whether a 5 V branch with a 400 mA inrush can be switched at all: the 100 mA setting will fold back on the inrush, and the 500 mA setting is the only one that lets the branch start.

Why 2.4 MHz matters here

At 2400 kHz the buck inductors are small enough to sit beside a 6 mm package, which is the whole point of an integrated PMIC. The cost is switching loss and a tighter minimum on time, so a rail that converts 5 V to 0.85 V runs at a low duty and has to be checked against the minimum controllable on time rather than assumed to regulate.

The high frequency also sets what the output capacitors have to be. A 1.8 A rail at 2.4 MHz with ceramic output capacitors needs far less capacitance than the same rail at 500 kHz, but the ESR and the loop stability still have to be checked against the document's recommended values rather than scaled by intuition.

Where this order code fits

It is the power tree for a Cortex-A8 or A9 board: industrial HMI panels, point of sale terminals, test equipment and personal navigation units running from a 5 V adapter or a single cell pack. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is this part still recommended for new builds? The addendum rows in SLDS206E are marked NRND, so a new build should confirm lifecycle status with the vendor before committing. Existing builds are unaffected.

What does the D0 in the order code mean? It is the silicon revision, not a package. The revision register at 5h reads 4.0 for D0, and the document publishes B1 orderable rows only.

Can the backup rails run from a coin cell alone? Yes. DCDC5 and DCDC6 take their input from the CC pin when the system rail is absent, and the IN_nCC flag reports which source is in use.

How many pieces are on a large reel? 2500 for the RSL VQFN in the published B1 row and 1000 for the PHP HTQFP. The D0 string row is not printed, so confirm the quantity on the offer.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.