Contact Us

TPS552892QWRYQRQ1

Brand: Texas Instruments
Texas Instruments TPS552892QWRYQRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS552892QWRYQRQ1 — Power Management & Signal Chain | Superb Automation

TPS552892QWRYQRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS552892QWRYQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS552892QWRYQRQ1: an automotive 36 V, 8 A buck-boost converter in a 21 pin QFN

TPS552892QWRYQRQ1 is an AEC-Q100 grade 1 synchronous buck-boost converter in a VQFN-HR (RYQ) body of 21 pins. The RYQ package is 3.0 mm by 5.0 mm with 21 pins and the marking is 52892Q, on a 3000 piece large reel. The Q1 suffix is the automotive part, and the W in the ordering string is part of the exact string a distributor has to quote.

Order code and package

TPS552892QWRYQRQ1VQFN-HR (RYQ), 21 pins, 3000 piece large reel, marking 52892Q, -40 to 125 C ambient
Finish and floor lifeNIPDAU, MSL level 2 at 260 C with a one year floor life, which is shorter than the level 1 parts on the same board
GradeAEC-Q100 grade 1, -40 C to +125 C ambient
Absolute maximum42 V on VIN and SW1, 20 V on VOUT and SW2, 6 V on EN and the logic pins, -0.3 V to 25 V on the compensation pins
Pin names worth knowingISP and ISN are the output current sense pair, CC is the open drain constant current flag, DITH/SYNC takes the spread spectrum or clock input
Sensing defaulttying ISP and ISN together to VOUT disables the output current limit, which is the configuration when the limit is not needed

Electrical parameters that decide the application

Input and output3.0 V to 36 V in, 0.8 V to 22 V out, 2.8 V to 3.0 V undervoltage lockout rising
Current8 A switch current, 7 A to 9 A average inductor current limit, 13 A peak high side limit during a transient
Power in boost mode60 W from a 12 V input, 45 W from a 9 V input
Reference1.2 V nominal, 1.188 V to 1.212 V window, 1 percent accuracy claimed
Switching frequency200 kHz at a 100 kOhm FSW resistor, 180 kHz to 220 kHz across the tolerance, programmable to 2.2 MHz and synchronisable to an external clock
Efficiency96 percent at 12 V in, 20 V out and 3 A, quoted over the whole load range
Current monitoring5 percent accurate output current monitor, and a programmable output current limit set by a resistor between ISP and ISN
ProtectionOutput overvoltage at 22.5 V to 24.5 V with 1 V hysteresis, average inductor current limit, cycle by cycle peak limit, short circuit protection and hiccup on sustained overload
Light loadprogrammable pulse frequency modulation or forced continuous mode, which is the choice between standby efficiency and flat ripple
Quiescent and shutdown760 uA typical into VIN, 0.8 uA typical and 3 uA maximum shutdown current into VIN
Compensationadjustable output voltage compensation against cable droop
EMIoptional spread spectrum on top of the clock synchronisation input

Family variants and how they differ

TPS55289-Q1the same converter family with the output current limit and the constant current flag brought out, which is what the CC pin on this ordering string implies
Grade comparisonthis is the grade 1 automotive part, so the -40 to 125 C ambient range and the AEC-Q100 qualification are part of the ordering string rather than an option
Packagethe 3.0 mm by 5.0 mm QFN is the only body this converter ships in, there is no leaded alternative to fall back on
Against a two stage solutionone buck-boost replaces a boost plus a buck where the rail has to hold through both a cold crank dip and a load dump recovery

Points to check before this part goes on a BOM

The four integrated switches are the point of the part. A 12 V automotive rail that drops to 3 V during a cold crank and rises past 20 V during a load dump cannot be handled by a buck alone, and a boost alone cannot hold a 12 V output from a 24 V alternator. The buck-boost keeps 0.8 V to 22 V at the output across the whole 3.0 V to 36 V input window, which is 60 W of delivery from a 12 V input and 45 W from 9 V.

Switching frequency is set by one resistor and the setting transfers into EMI work. 100 kOhm gives 200 kHz typical with a 180 kHz to 220 kHz spread, and the part will run up to 2.2 MHz from a smaller resistor. Higher frequency shrinks the inductor and the capacitors, and the optional spread spectrum plus the DITH/SYNC clock input are there to keep the peak off a single bin in a conducted emissions scan.

Current limit is two separate mechanisms and they protect different things. The average inductor current limit of 8 A typical holds the conversion in check, while the 13 A peak high side limit catches a transient before the average loop can react. The optional output current limit sits on the ISP and ISN sense resistor and is the one to fit when the load itself has to be held at a fixed current, and the CC pin reports when it is active.

The 3 V undervoltage lockout is where an automotive board has to be checked rather than assumed. During a cold crank the input can fall below the 2.8 V to 3.0 V rising threshold, at which point the converter stops instead of holding the rail, so a system that must survive the dip either accepts the dropout or adds input holdup capacitance.

Reading the ordering string before quoting

TPS552892QWRYQRQ1 carries four pieces of information in the letters and digits after the base number: the automotive qualification, the 3.0 mm by 5.0 mm QFN, the 3000 piece reel and the grade 1 temperature range. A quote written against TPS552892 or against a shortened string describes a different product, and an automotive customer auditing incoming material will reject it against the drawing.

The package is the other constraint worth flagging early. There is no leaded or larger body alternative for this converter, so a board that has to be reworked by hand needs the stencil and the reflow profile for an MSL 2 QFN rather than a level 1 part. The one year floor life is the practical consequence: reels held past a year go through the bake cycle stated on the shipping label.

Where this order code fits

It belongs on automotive rails that have to survive cold crank and load dump: cluster and infotainment supplies, camera and radar power, and any 12 V or 24 V board that needs a regulated rail above and below the battery voltage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Is the W version relevant to ordering? Yes. The full ordering string is TPS552892QWRYQRQ1 and the letters carry the package and qualification rather than a packing choice, so a quote written against a shortened string is not the same part. The 3000 piece large reel is the only carrier listed.

How is the output current limit set? By a resistor between ISP and ISN, with a larger resistor giving a lower limit. Tying ISP and ISN together to VOUT disables the limit, which is the configuration to use when the load does not need current regulation.

What is the difference between the two current limits in the tables? The average inductor current limit, 8 A typical with a 7 A to 9 A window, protects the conversion, and the 13 A peak high side limit covers a fast transient. Neither is the output current limit, which is the separate sense resistor function.

Why level 2 moisture sensitivity? The 3.0 mm by 5.0 mm QFN is rated MSL 2 at 260 C with a one year floor life, so the reel has to be handled differently from the level 1 parts that share the same assembly line. Baking rules follow the shipping label, not the family.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.