Contact Us

TPS54060DGQR

Brand: Texas Instruments
Texas Instruments TPS54060DGQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54060DGQR — Power Management & Signal Chain | Superb Automation

TPS54060DGQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54060DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54060DGQR: 3.5 V to 60 V input 0.5 A step down converter with Eco-mode in a 10 pin HVSSOP

TPS54060DGQR is a wide input current mode buck with a 200 milliohm high side FET, a 0.8 V reference and a switching frequency set by one resistor anywhere from 100 kHz to 2.5 MHz in a HVSSOP (DGQ) body of 10 pins. It accepts 3.5 V to 60 V on the input, delivers 0.5 A and holds the output at any voltage above the 0.8 V reference. The high side FET is 200 milliohm at 12 V, the quiescent current is 116 microamp, the shutdown current is 1.3 microamp and the current limit is bounded at 0.6 to 0.94 A.

Order code and package

Order code read outTPS54060 DGQ R: converter TPS54060, DGQ ten pin HVSSOP with PowerPAD, R large tape and reel
PackageHVSSOP (DGQ), 10 pins with an exposed thermal pad on the underside, the leaded body that is easier to inspect than the VSON option
Carrier in the vendor addendumTPS54060DGQR at 2500 pieces on a large reel; TPS54060DGQ is the same part in an 80 piece tube
Moisture levelLevel 1, 260 degrees peak reflow, unlimited floor life
Lead finishNickel palladium gold, quoted as NIPDAUAG
Temperature rangeJunction minus 40 to plus 150 degrees, storage minus 65 to plus 150
Absolute maximum65 V on VIN and on the switch node, 8 V across BOOT to PH, 5 V on EN, 3 V on VSENSE and COMP, 6 V on PWRGD, 3.6 V on RT/CLK

Electrical parameters that decide the application

Input range3.5 V to 60 V, with an internal undervoltage lockout at 2.5 V that can be raised with a divider on the enable pin
Output rangeAdjustable from the 0.8 V reference upward, with the reference held at 0.792 to 0.808 V over temperature
Output current0.5 A continuous, protected by a current limit of 0.6 A minimum and 0.94 A typical
High side FET200 milliohm typical and 410 milliohm maximum at 12 V, 300 milliohm typical at 3.5 V, which is why the part is a 0.5 A device rather than a 1 A one
Switching frequency100 kHz to 2.5 MHz set by the resistor on RT/CLK, with 200 kohm giving 581 kHz typical and a 450 to 720 kHz window; an external clock can be applied for 300 kHz to 2200 kHz
Quiescent current116 microamp typical and 136 microamp maximum while regulating without switching, and 1.3 microamp typical, 4 microamp maximum, shut down
Enable threshold1.25 V typical with a 0.9 to 1.55 V window, and a hysteresis current of 2.9 microamp that sets the UVLO divider behaviour
Soft start and trackingThe SS/TR pin charges at 2 microamp, and a capacitor on that pin sets the ramp; the same pin accepts an external voltage for tracking a second rail
Power goodThe open drain PWRGD pin releases when the feedback reaches 94 percent of the reference and pulls low below 92 percent, with a second window at 109 and 107 percent; on-resistance is 50 ohm at 3 mA
Thermal shutdown182 degrees junction, which is higher than the 150 degree rating because it is a fault guard rather than a control loop
Thermal resistance62.5 degrees per watt junction to ambient on a standard board for the HVSSOP body, 57 on a custom board with thermal vias
Eco-modePulse skipping at light load that drops the effective frequency and keeps the quiescent draw at 116 microamp instead of holding continuous switching

Bodies, pin functions and the parts beside it

TPS54060DGQRthe part on this page, 10 pin HVSSOP, 2500 pieces on a reel, 150 degree junction rating
TPS54060DRCRthe same die in the 10 pin VSON body, 40 degrees per watt junction to ambient, chosen when the board has no room for the leaded package
RT/CLK pinone resistor sets the frequency, or an external clock in the 300 kHz to 2200 kHz range can drive the pin for synchronisation
SS/TR pina capacitor sets the start ramp and an applied voltage turns the pin into a tracking input for a second rail
PWRGD pinopen drain with a 50 ohm pull down and a two sided window, so it reports both an undervoltage and an overvoltage condition

Points to check before this part goes on a BOM

A 60 V input rating with a 0.5 A output is an unusual combination and it is the reason this part exists. Most rails that start at 48 V need only a housekeeping current, and a converter rated at 1 A or more would either need a much larger inductor or would lose efficiency at that current. The 200 milliohm high side FET is what keeps the part small, and it also sets the ceiling: at 0.5 A the conduction loss is 50 mW, while at 1 A it would be 200 mW in the FET alone.

The current limit window of 0.6 to 0.94 A is narrow in absolute terms and wide in ratio. Because the part is rated at 0.5 A, the limit sits only 20 percent above the rating at the low end, so a load that draws a hard 0.55 A during a transient can reach the limit. That is usually harmless, but a board that expects 0.5 A continuous plus a capacitive inrush should have the soft start ramp checked against the limit rather than assumed.

Eco-mode is what keeps the standby draw at 116 microamp. Below the load where the inductor current would reverse, the part skips pulses and lets the output ripple grow, which is why the ripple at a few milliamps is much larger than the ripple at 100 mA. A rail feeding a comparator or a radio that cannot tolerate that ripple has to be loaded above the boundary, or the output capacitor has to be increased, or the part has to be replaced with a forced continuous type.

The SS/TR pin is doing two jobs and the second one is easy to miss. As a soft start pin it takes a capacitor and charges it at 2 microamp, giving a ramp that is easy to calculate. As a tracking input it takes a voltage and the output follows it, which is how a customer sequences a 1.2 V core rail behind a 3.3 V rail without a separate sequencer. The matching between SS/TR and the feedback is specified at 45 mV, so the tracking is close but not exact.

The PWRGD window is wider than most similar parts: it releases at 94 percent and pulls low at 92 percent, and it also reports a high side condition at 109 and 107 percent. A supervisor that waits for PWRGD to start the next rail will therefore wait until the output is within 6 percent of nominal, and it will also see a fault if the output is driven above nominal by an external source, which is useful on a bus where a second supply can back feed.

Choosing between the HVSSOP and VSON bodies is mostly a thermal decision. The HVSSOP is 62.5 degrees per watt on a standard board and 57 on a board with thermal vias, while the VSON is 40 degrees per watt. At 0.5 A and a 5 V output from 48 V the part dissipates roughly 0.5 W, which is 31 degrees of rise in the VSON and 48 in the HVSSOP, so the leaded body is fine at a 70 degree ambient but marginal at 105 degrees.

Where this order code fits

Suits 12 V, 24 V and 48 V industrial and commercial low power systems, aftermarket automotive accessories such as video, GPS and entertainment units, and any board that needs a 0.5 A housekeeping rail from a high voltage bus. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can this part take a 48 V bus directly? Yes. The input range is 3.5 V to 60 V with 65 V absolute maximum, so a nominal 48 V rail with a transient margin is inside the rating, and the 200 milliohm high side FET is what keeps the dissipation at 0.5 A manageable.

How is the switching frequency chosen? One resistor from RT/CLK to ground. 200 kohm gives about 581 kHz, the usable range is 100 kHz to 2.5 MHz, and an external clock between 300 kHz and 2200 kHz can drive the same pin for synchronisation.

What sets the output voltage? A divider from the output to VSENSE against a 0.8 V reference that holds 0.792 to 0.808 V over temperature, so a one percent divider pair gives roughly plus or minus 2 percent at the output.

What is the current limit? 0.6 A minimum and 0.94 A typical, so the 0.5 A rating leaves only a small margin. A load with a large inrush should have the soft start ramp checked against that window.

Does the part support sequencing? Yes, through the SS/TR pin. A capacitor sets a soft start ramp and an applied voltage makes the output follow an external ramp, with the SS/TR to feedback matching specified at 45 mV.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.