Contact Us

TPS62112RSAR

Brand: Texas Instruments
Texas Instruments TPS62112RSAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62112RSAR — Power Management & Signal Chain | Superb Automation

TPS62112RSAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62112RSAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62112RSAR: a 3.1 V to 17 V, 1.5 A synchronous buck with a fixed 5 V output

TPS62112RSAR is a 1.5 A synchronous step down converter with a fixed 5 V output in a VQFN (RSA) body of 16 pins. The RSA body is the 16 pin VQFN at 4.00 mm by 4.00 mm. In the TPS6211x family the last digit selects the output: the TPS62110 is adjustable from 1.2 V to 16 V, the TPS62111 is fixed at 3.3 V, the TPS62112 is fixed at 5 V and the TPS62113 is adjustable with the enhanced low battery input and output pair.

Order code and package

TPS62112RSARVQFN (RSA), 16 pins, 4.00 mm by 4.00 mm, 3000 piece large reel, fixed 5 V output
TPS62112RSATthe same body on a 250 piece small reel
TPS62110RSARadjustable 1.2 V to 16 V from an external divider, standard low battery input and output
TPS62111RSARfixed 3.3 V, otherwise the same part
TPS62113RSARadjustable with the enhanced low battery function, which is the variant for a battery monitor that has to act before the rail drops
Temperature and finish-40 to 85 C, tape and reel only, with the R suffix for 3000 pieces and the T suffix for 250

Electrical parameters that decide the application

Input range3.1 V to 17 V operating, which is the range that covers a 2 to 4 cell lithium pack and a 12 V or 15 V industrial rail
Output5 V fixed on this member, with the tolerance specified as 3 percent over 0 mA to 1500 mA and an input from 5.5 V to 17 V
Output current1.5 A, with the maximum depending on input voltage as the document's own curves show
Power switchesintegrated N and P channel MOSFETs with synchronous rectification, which is what removes the external diode
Switching frequency1 MHz nominal, synchronisable to an external clock from 0.8 MHz to 1.4 MHz
Current limit2600 mA on the P channel switch at 7.2 V in and a 5 V output, which is the peak figure the inductor has to survive
Quiescent current20 uA typical in the operating mode the front page describes, with the electrical table printing a figure below 2 uA under the SYNC low, no load condition
Shutdownbelow 2 uA, with the enable pin forcing the part into that state
Lockout2.8 V to 3.1 V with 300 mV of hysteresis, so a 3.3 V rail is above it and a 3.0 V rail is not
Duty cycle100 percent maximum, which is what gives the lowest dropout when the input falls toward the output
Light loadPFM at light currents and PWM only when the SYNC pin is held high, which is the trade between efficiency and ripple
Protectioncycle by cycle current limit, thermal shutdown at 145 C, and soft start that runs from the enable pin

Family variants and how they differ

TPS62112 against the adjustable TPS62110the fixed version removes the divider and its tolerance but locks the rail at 5 V
TPS62113the same adjustable range with the enhanced low battery comparator, which reports a falling input before the converter drops out
Synchronisationthe SYNC pin accepts a clock between 0.8 MHz and 1.4 MHz, so several rails can be moved off a common frequency
Against a linear regulator1.5 A at 5 V from 12 V is 58 percent efficient in a linear part and above 90 percent here, which is the whole argument for a switcher on a 12 V bus
Packagethe 4 mm VQFN is the only body in this family, so there is no smaller alternative within the same order code

Points to check before this part goes on a BOM

The fixed 5 V output has a condition attached that decides whether it is a 5 V rail at all: the 3 percent tolerance is specified from 5.5 V of input upward. Below that the part still regulates, but 100 percent duty cycle means the output follows the input minus the drop across the high side switch and the inductor, so a 5 V input cannot give a 5 V output. A system that runs this part from a 5 V bus should expect the rail to track the bus rather than hold 5 V.

The current limit is a peak switch limit of 2600 mA, not an output current. At 5 V out from 12 V in the inductor ripple is modest and 1.5 A of output is comfortably inside, but at 5.5 V in the duty cycle is close to 100 percent and the same 1.5 A output leaves very little margin, which is why the document's maximum output current curves fall as the input approaches the output.

Light load behaviour is set by the SYNC pin, and the choice is not cosmetic. With SYNC low the part enters PFM and the quiescent current falls to a few microamps, which is what a battery product needs. With SYNC high it stays in PWM, the ripple is constant and predictable, and the efficiency at 10 mA falls. A radio or an ADC on the same rail will hear the difference between those two modes.

The 1 MHz switching frequency and the external synchronisation window are what make this part usable beside other rails. Because it can be locked to a clock from 0.8 MHz to 1.4 MHz, a system with several converters can put them on one frequency and move the beat products away from a receiver band, which is not possible on a fixed frequency part.

Where the 20 uA figure comes from

The front page quotes 20 uA of quiescent current, while the electrical table prints a much smaller number under a specific condition with the SYNC pin low and no load. The two are not in conflict: the low figure is the PFM idle current, and the 20 uA is the operating current with the converter running. A specification should quote the mode it means, because a battery product that holds SYNC high never sees the low figure.

The same applies to the shutdown row: below 2 uA is quoted with the enable pin low, and that is the number that decides how long a product survives in storage with the battery connected.

Choosing between the four members

The four order codes differ only in output voltage and in the low battery function, so a board that needs 3.3 V rather than 5 V changes the last digit and leaves the footprint alone. The TPS62113 adds a comparator that flags a falling input, which is the difference between a product that warns the user and one that simply shuts down.

All four are pin compatible in the same 16 pin VQFN, which is why this family is still sourced for repairs on equipment built around a 12 V or 15 V bus.

Where this order code fits

It makes a 5 V rail from a 12 V or 15 V bus and from a 2 to 4 cell lithium pack, which is the point of load case on organisers, handheld scanners and industrial control boards. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is the 5 V output regulated with a 5 V input? Not to the 3 percent specification. Tolerance is specified from 5.5 V of input, and below that the part runs at 100 percent duty and the output follows the input minus the switch and inductor drop.

How do I get low quiescent current? Hold SYNC low so the part enters PFM at light load. Holding SYNC high keeps it in PWM and the idle current rises.

Can several rails share one clock? Yes. The SYNC pin accepts an external clock from 0.8 MHz to 1.4 MHz.

Which member is the 3.3 V version? The TPS62111. The TPS62112 is 5 V, the TPS62110 is adjustable and the TPS62113 is adjustable with the enhanced low battery function.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.