Contact Us

CD4069UBM96

Brand: Texas Instruments
Texas Instruments CD4069UBM96 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4069UBM96 — Power Management & Signal Chain | Superb Automation

CD4069UBM96

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4069UBM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4069UBM96: the unbuffered hex inverter on a 2500 piece SOIC reel

The CD4069UBM96 is the large tape and reel entry for the CD4069UB, six CMOS inverters on one die in a 14-lead small outline body. The vendor product page carries the device as ACTIVE with the descriptor 6-ch, 3-V to 18-V inverters, an output drive of 6.8 mA in both directions, a maximum supply current of 150 microamps, and an operating range of minus 55 to plus 125 degrees. The reel row is 2500 pieces in a large tape and reel, moisture level 1 at 260 degrees, lead finish nickel palladium gold, and the marking printed on the body is CD4069UBM rather than the orderable string.

The letter U in the string is the part that decides where this device belongs. The vendor marks the family Unbuffered in the feature list and states in the description that the six inverters are intended for general purpose inversion where the medium power TTL drive and the logic level conversion of the CD4009 and CD4049 are not required. An unbuffered gate is a single complementary pair, a buffered gate adds gain stages behind it. Two documents on the product page cover the difference, the data sheet and the application note on buffered and unbuffered CD4xxxB characteristics, and the note is the one that explains why an unbuffered inverter is used as a small signal amplifier in oscillator circuits rather than as a line driver.

The CD4069UB rows as the addendum publishes them

Part classSix CMOS inverters, unbuffered, one die
Vendor descriptor6-ch, 3-V to 18-V inverters
Vendor statusACTIVE, catalogue rating
Data sheetSCHS054E, original November 1998, revised January 2019
Document date on the page15 January 2016, which does not match the January 2019 header
Package addendum date18 September 2026
Supply range3 V to 18 V operating, 20 V type rating in the headline
Output drive6.8 mA sink and source at 15 V
Supply current150 microamps maximum
Propagation delay30 ns typical at 10 V into 50 pF
Input current1 microamp at 18 V, 100 nA at 18 V and 25 degrees
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
SOIC body14 leads, 51.9 square millimetres, 8.65 by 6 mm
SOIC tube rowCD4069UBM, 50 pieces, Active
SOIC reel rowCD4069UBM96, 2500 pieces, large tape and reel, Active
Obsolete SOIC rowCD4069UBMT, blank quantity, Call TI
SOP reel rowCD4069UBNSR, 2000 pieces, Active
TSSOP rowsCD4069UBPW tube Obsolete, CD4069UBPWR reel 2000 Active
Ceramic rowsCD4069UBF 25 pieces Active, CD4069UBF3A NRND
Military rowsJM38510/17401BCA and M38510/17401BCA, NRND
PDIP rowCD4069UBE, 25 pieces in a tube, Active
Thermal, 14-lead SOIC86 degrees per watt junction to ambient in the family document

Four rows on that table decide what a purchase order can actually match. The tube row at 50 pieces and the reel row at 2500 pieces are both live, the small tape and reel row CD4069UBMT is closed, and the TSSOP tube closed while the TSSOP reel survived. That last pattern repeats across the whole CD4000B family and it is the single most common reason a bill of materials shows a valid looking string that no distributor can ship.

What the parametric table fixes

The six channels share a 3 to 18 V supply and a drive of 6.8 mA at 15 V, which is enough for a slow CMOS load and not enough for a 74 series bus. Quiescent current is 150 microamps maximum over the full temperature range, and the vendor states that the part is tested for quiescent current at 20 V, which is the corner where leakage grows and where a sleepy battery product would be caught. Input current is 1 microamp at 18 V over temperature and 100 nA at 18 V and 25 degrees, so a 1 megohm pull up is not disturbed by the input itself.

Noise margin is quoted at all three parametric rails, 1 V at 5 V, 2 V at 10 V and 2.5 V at 15 V, which is roughly 20 per cent of the rail at every point. That figure is the one that matters on a board that mixes a 3.3 V sensor with a 12 V relay rail, because it says how much ground bounce the input can absorb before the gate changes state on its own. The 30 ns propagation figure is typical at 10 V into 50 pF and it is the number the product page prints; the guaranteed limits for 5 V, 10 V and 15 V sit in the dynamic table of the data sheet, and the two should not be treated as the same thing.

One inconsistency is worth naming. The headline of the data sheet calls the family a 20 V type, and the product page range stops at 18 V. Both are vendor statements and they describe different things: the 20 V figure is the supply level at which quiescent current is tested and the absolute maximum is 20.5 V, while the parametric table stops at 15 V. A board that runs at 18 V therefore has DC limits but no guaranteed switching limit, and the page should not be read as a promise that the gate is characterised at 18 V.

Where the small outline body fits

The 14-lead SOIC measures 51.9 square millimetres against 181.42 square millimetres for the plastic DIP, 79.56 for the SOP and 32 for the TSSOP. On a board that already has a DIP footprint and a wave solder line, the DIP is the cheaper part to place, and the 25 piece tube is the packing that suits a repair or a pilot build. On a reflow line with a pick and place machine, the 2500 piece reel is the only format that runs without stopping, and the moisture level 1 rating means the reel needs no bake before use, which is not true of every logic family on a shelf.

The thermal number explains the body choice more than the area does. Junction to ambient is 80 degrees per watt in the plastic DIP, 86 in the SOIC, 76 in the SOP and 113 in the TSSOP. At the 150 microamp quiescent current the part dissipates almost nothing, so the thermal number only starts to matter when the output is loaded and several channels switch at once. A hex inverter driving six 50 pF loads at 1 MHz from a 15 V rail is still well inside the package limit, but the same part driving a capacitive cable at 10 MHz is not, and that is the case where the TSSOP number should be read before the board is released.

What the documents do not publish

The product page gives one dynamic figure, typical at 10 V, and no maximum. It gives no output capacitance, no short circuit current and no latch up figure. The data sheet carries those tables, but the page itself cannot be used as a specification, which matters when a customer sends a screenshot of the page as the requirement. The other gap is packaging: the addendum prints the reel and tube rows, but the page does not print the tape pocket dimensions, so a customer who needs the carrier tape drawing has to pull the package materials section of the same document.

Second source and long term availability

The CD4069UB has been made by several vendors under the same number, and the 14-lead SOIC pin out is old enough that most of them still offer it. A cross to a 74HC04 or a 74HCU04 is not a drop in, because the input threshold, the drive and the buffered or unbuffered structure all change the behaviour of an oscillator. The pin to pin cross reference page sets out how we check a candidate against the original, and the component obsolescence management page covers what to do when only the tube rows disappear and the reel stays.

What to send with an enquiry

Send the exact string, the body, the quantity and the date you need it. If the board is through hole, say so, because the tube is 25 pieces and a 500 piece build needs twenty tubes booked as one line. If the board is reflow, say whether the line can take a 330 mm reel, because the 2500 piece reel is the only format that avoids a hand load. The BOM scrubbing page explains how we reconcile the orderable rows against a build quantity before a schedule is confirmed.