Contact Us

CD4066BE

Brand: Texas Instruments
Texas Instruments CD4066BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4066BE — Power Management & Signal Chain | Superb Automation

CD4066BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4066BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4066BE: four bilateral switches in the 14-lead plastic DIP

The CD4066BE is the plastic dual in line member of the CD4066B family, four independent bilateral analogue switches on the 3 V to 20 V CMOS process. The vendor describes the part as a 20 V, 1 to 1 single pole single throw, four channel analogue switch with a 10 picoamp on state leakage and marks it ACTIVE. The parametric table gives four channels, a 1 to 1 single pole single throw configuration, single supply options of 3.3, 5, 12, 16 and 20 V, dual supply options of plus or minus 2.5, 5 and 10 V, a typical on resistance of 125 ohms, an on capacitance of 8 picofarads, a typical supply current of 0.01 microamps, a bandwidth of 40 MHz and a 10 milliamp continuous channel current.

The row reads Active, plastic DIP with 14 leads at 181.42 square millimetres, 25 pieces in a tube, RoHS yes with a nickel palladium gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, minus 55 to plus 125 degrees and the marking CD4066BE. The ceramic body sits beside it as CD4066BF and CD4066BF3A, and the military drawing rows JM38510 and M38510 parts are on the same addendum at 25 pieces in a tube.

The CD4066BE row as the vendor addendum publishes it

Part classQuad bilateral analogue switch, single pole single throw
Vendor descriptor20 V, 1 to 1, 4 channel analogue switch, 10 pA on state leakage
Vendor documentSCHS051J, revised August 2024, CD4066B
Configuration1 to 1, four channels, independent control pins
Digital switching15 V digital or plus or minus 7.5 V peak to peak
Single supply3.3, 5, 12, 16 and 20 V
Dual supplyPlus or minus 2.5, 5 and 10 V
On resistance125 ohms typical at 15 V, matched to within 5 ohms over the range
On state leakage10 picoamps typical
On capacitance8 picofarads typical
Bandwidth40 MHz
Isolation80 dB typical at 10 kHz with a 1 kilohm load
DistortionBelow 0.5 per cent typical at 1 kHz and 5 V peak to peak
Supply current0.01 microamps typical
Continuous current10 milliamps maximum through any channel
Package for this codePDIP (N), 14 leads, 181.42 square millimetres
Packing25 pieces in a tube
StatusActive, production
Part markingCD4066BE
SOIC reel rowCD4066BM96, 2500 pieces, marking CD4066BM
TSSOP reel rowCD4066BPWR, 2000 pieces, marking CM066B
Obsolete rowsCD4066BM, CD4066BMT, CD4066BNS and CD4066BPW

Four switches with no decoding between them

Each of the four switches has its own control pin, and there is no address decoding, no inhibit line shared across the package and no internal connection between channels. That makes the part a set of four independent gates rather than a multiplexer, and it is the reason it appears in circuits that switch unrelated signals: a gain range here, a filter tap there, a mute on one path and a sample and hold on another.

The signal path is bilateral, so the same switch works in either direction, and the 8 picofarad on capacitance with the 40 MHz bandwidth is the widest of the family. A board that routes audio, a low level sensor signal or a small reference voltage through these switches sees a part that behaves as a small resistance and a small capacitance, and nothing else.

What the 125 ohm figure does to a signal

At 15 V the typical on resistance is 125 ohms, and the vendor states that it is matched to within 5 ohms over the signal range. That matching is the property that matters for audio and for a switched gain network: two switches in the same package track each other, so a differential path keeps its balance and a gain network keeps its ratio. A single switch used as a variable element does not benefit, because the absolute value moves with temperature and with the signal level.

The distortion figure of below 0.5 per cent typical at 1 kHz and 5 V peak to peak is the number that decides whether the part can sit in an audio path. Half a per cent is audible on a pure tone and inaudible on speech, so the part is acceptable for a monitor path and marginal for a measurement path. A board that needs lower distortion uses a relay or a purpose built audio switch, and the reason is the resistance modulation rather than the resistance value.

Isolation, leakage and the off state

Eighty decibels of isolation at 10 kHz into a 1 kilohm load is the off state figure, and it is what allows the part to disconnect one source while another drives the same node. At higher frequencies the isolation falls because the off capacitance couples the signal through, so a board that switches a radio frequency signal needs a different device. At audio and at direct current the figure is adequate.

The 10 picoamp on state leakage is the figure that limits the part in high impedance circuits. Through a 1 megohm source that is 10 microvolts of offset, which is acceptable for a monitoring channel and not for a precision instrument. The off state leakage is lower again, and the vendor publishes both, which is more than most analogue switch data sheets do.

The supply current of 0.01 microamps typical is the figure that makes the part usable in a battery instrument that leaves a signal path connected for years. Four switches held off draw almost nothing, and the control pins are the only path that can leak. A board that leaves the switches powered while the rest of the circuit sleeps keeps its routing intact without a measurable drain.

Through-hole body and the switch that has to be serviceable

A quad bilateral switch in a 14-lead plastic DIP is a part that a technician can replace in a socketed instrument, and that is where most of these still go. Test equipment, audio consoles and industrial controllers that are repaired rather than replaced all keep a through-hole switch on the board, because the alternative is a surface mount part on a card that has to be replaced whole.

The body is 181.42 square millimetres at 19.3 by 9.4 millimetres, which is four times the TSSOP body, and the tube of 25 is one build for a small instrument. On a board that is surface mount from end to end, the reel rows are the natural choice and the plastic DIP only appears as a repair part.

Second source and the rows that have closed

Four rows of this family are obsolete: the SOIC tube, the SOIC tube variant, the SOP tube and the TSSOP tube. The live surface mount formats are the 2500 piece SOIC reel and the 2000 piece TSSOP reel, and the plastic DIP still ships in a 25 piece tube. A customer who needs a small quantity of a surface mount switch is therefore looking at a cut reel rather than a tube.

The last time buy and LTB planning page covers how a final order is sized for a family that has already closed four rows, and the obsolete part cross reference hub collects the other quad switch families with the same pattern. A board that can move to a modern switch should read the drop in replacement verification page first, because a lower on resistance usually comes with a narrower analogue range.

What to send with an enquiry

Send the string, the signal range, the number of switches in use and the annual quantity. If the circuit is audio, say so, because the distortion figure is the number that decides whether this part or a purpose built switch is the right answer. If the board is through-hole and socketed, the .A row is also available and widens the stock that can be quoted.