Contact Us

CD4060BM-2

Brand: Texas Instruments
Texas Instruments CD4060BM-2 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4060BM-2 — Power Management & Signal Chain | Superb Automation

CD4060BM-2

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4060BM-2 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4060BM-2: the page suffix that is not a vendor string

The string on this page ends in minus two, and that suffix belongs to this catalogue rather than to the vendor. TI publishes the CD4060B family in three surface mount bodies and one through-hole body, and the orderable string for the small outline tube is CD4060BM. There is no CD4060BM-2 in the package option addendum dated 26 September 2026, and there never has been: the minus two is the artefact of a second catalogue entry created for the same part, which is how the suffix appears on this site.

That matters because a search engine, a distributor and a customer all read the string literally. The die behind this page is the CD4060B, a fourteen stage ripple carry binary counter with an on-chip oscillator, described by the vendor as a CMOS 14 stage ripple carry binary counter divider and oscillator and marked ACTIVE. The parametric table gives a counter function, ten bits, standard CMOS input, push pull output and an operating range of minus 55 to plus 125 degrees.

The CD4060BM rows as the vendor addendum publishes them

Part class14 stage ripple carry binary counter with on-chip oscillator
Vendor documentSCHS049C, revised October 2003, acquired from Harris Semiconductor
Vendor string for this bodyCD4060BM, SOIC, 40 pieces in a tube, Active
String on this pageCD4060BM-2, catalogue suffix, not a vendor row
Reel row of the same bodyCD4060BM96, 2500 pieces, marking CD4060BM
PackageSOIC (D), 16 leads, 59.4 square millimetres at 9.9 by 6 mm
Lead finishNIPDAU
Moisture levelLevel 1 at 260 degrees, unlimited floor life
Part markingCD4060BM
Counter stages14, with ten outputs brought out
Clock rate12 MHz at 15 V
OscillatorRC or crystal configuration, all active parts on chip
RC oscillator floor690 kHz minimum at 15 V
ResetCommon reset, fully static operation
Inputs and outputsBuffered, with a Schmitt trigger on the input pulse line
Supply range3 V to 18 V, with 5 V, 10 V and 15 V parametric ratings
Quiescent currentTested at 20 V on every unit
Input current1 microamp maximum at 18 V over temperature, 100 nA at 25 degrees
NRND SOP rowsCD4060BNSR and CD4060BNSR.A, not recommended for new builds
TSSOP reel rowCD4060BPWR, 2000 pieces, marking CM060B
Obsolete rowsCD4060BMT and CD4060BPW, quantity blank, Call TI
PDIP rowCD4060BE, 25 pieces in a tube

What a duplicate catalogue entry does to a purchase order

A duplicate entry is not a duplicate part, and the difference shows up at the point of order. A customer who sends the string from this page to a distributor will be told that CD4060BM-2 does not exist, which is correct, and the reply may then stop there. The part does exist: it is CD4060BM in the 40 piece tube or CD4060BM96 on the 2500 piece reel, and both are Active on the current addendum.

This site keeps the page rather than removing it because the address carries whatever search traffic has accumulated, and because a redirect would send a visitor to a page that does not answer their question. What the page can do is state the correct string in the first paragraph, which is what the two paragraphs above do. That is the honest resolution: the page exists, the die exists, and the string a buyer should use is on the page.

The counter itself, and why it survives

Fourteen binary stages with an oscillator on the same die cover division ratios up to sixteen thousand three hundred and eighty four without a second package. The oscillator runs in RC or crystal configuration with all active components on chip, so a timer needs one resistor, one capacitor and this part. The full static operation means the clock can stop anywhere and the state is held, which is what makes the part usable in a long interval timer that spends most of its life with the clock off.

At 5 V the counter still divides, and the speed claim does not travel with it. The 12 MHz figure belongs to a 15 V supply and the vendor does not print a 5 V value in the text of this document, because the 2003 revision is a scan and the switching tables are images. A board that counts a 100 kHz signal at 5 V is well inside what the part does on the bench, and a board that wants to count a megahertz at 5 V should measure the part rather than trust the 15 V number. That distinction is the one thing this page cannot resolve from the document, and it says so rather than quoting a figure it does not have.

The ten outputs that are brought out are the upper stages, not all fourteen, and the ratios a board can use directly start at sixteen. A timer that needs an odd ratio has to take feedback from an output back to the reset or to the input, which is a board level decision. A tone generator that needs a power of two ratio takes one output and nothing else. The 12 MHz clock rate at 15 V and the 690 kHz minimum RC frequency at the same supply are the two speed figures the vendor prints, and both are 15 V figures.

Power-up behaviour on a long interval timer

The common reset clears every stage, and the vendor does not publish a defined power-up state for the counter. A timer therefore needs the reset driven after the supply settles, usually by an RC network on the reset pin, and it needs that network sized for the slowest supply ramp the product will see. Without it the first interval after power up can be shorter than the intended period, which on a product that controls a pump or a heater is a fault that appears only in the field.

The Schmitt trigger on the input pulse line is what lets the part count a slow edge from a phototransistor or an RC network. It converts one slow transition into one count, provided the noise riding on that edge is faster than the hysteresis. A mechanical contact still needs a debounce, and the Schmitt input helps with the edge rather than with the bounce.

The three live formats and the one that is not recommended

The die ships in a 25 piece plastic DIP tube, a 40 piece SOIC tube, a 2500 piece SOIC reel, a 2000 piece TSSOP reel and a 2000 piece SOP reel that the vendor marks not recommended for new builds. That last row is the one to avoid on a new board even though it is still orderable, and it is the row that most often appears in an old approved vendor list because it was the cheapest format at the time.

For a customer who needs between forty and three hundred pieces, the SOIC tube is the practical format: it avoids a cut reel and it can be issued to a small build without a moisture bag. For a build above three hundred, the reel is cheaper per piece once handling is counted. That crossover is covered on the kitting service page, and the component obsolescence management page explains how the SOP row being marked not recommended is treated in a long life bill of materials.

What to send with an enquiry

Send the string as it appears on this page and say that it ends in minus two, because that is the fastest way to get the correct vendor string back. Add the division ratio, whether the oscillator is RC or crystal, the supply rail and the annual quantity. The BOM scrubbing page explains how a line with a catalogue suffix is reconciled against the vendor addendum before a quote is issued.