CD4052BM96
Product Specifications
CD4052BM96
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4052BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4052BM96: the dual 4 channel multiplexer on a 2500 piece SOIC reel
The CD4052BM96 is the small outline reel member of the CD4052B, a dual 4 channel analogue multiplexer with two independent 4 to 1 switches sharing one pair of address lines. The vendor describes it as a 20 V, 4 to 1, two channel analogue multiplexer with logic level conversion and marks it ACTIVE. The parametric table gives two channels, a 4 to 1 configuration, a typical on resistance of 125 ohms, an on capacitance of 18 picofarads, a maximum on state leakage of 0.3 microamps, a typical supply current of 0.04 microamps, a bandwidth of 25 MHz and a 10 milliamp continuous channel current.
The row reads Active, SOIC body with 16 leads at 59.4 square millimetres, 2500 pieces on a large tape and reel, RoHS yes, nickel palladium gold finish, moisture level 1 at 260 degrees with unlimited floor life, minus 55 to plus 125 degrees and the marking CD4052BM. The tube row of the same body, CD4052BM, is obsolete with a blank quantity and a Call TI instruction, and the older reel suffixes BM96G3 and BM96G4 are obsolete as well.
The CD4052BM96 row as the vendor addendum publishes it
| Part class | Dual 4 channel analogue multiplexer and demultiplexer |
| Vendor descriptor | 20 V, 4 to 1, two channel analogue multiplexer, logic level conversion |
| Vendor document | SCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B |
| Configuration | 4 to 1, two independent channels, common address lines |
| Package for this code | SOIC (D), 16 leads, 59.4 square millimetres at 9.9 by 6 mm |
| Packing | 2500 pieces on a large tape and reel |
| Status | Active, production |
| Lead finish | NIPDAU |
| Moisture level | Level 1 at 260 degrees, unlimited floor life |
| Part marking | CD4052BM |
| Sibling reel row | CD4052BM96.A, same quantity |
| Obsolete SOIC rows | CD4052BM, CD4052BMT, CD4052BM96G3, CD4052BM96G4 |
| SOP reel row | CD4052BNSR, 2000 pieces |
| TSSOP reel row | CD4052BPWR, 2000 pieces, marking CM052B |
| Obsolete TSSOP row | CD4052BPW, quantity blank, Call TI |
| PDIP row | CD4052BE, 25 pieces in a tube |
| Single supply | 3.3, 5, 12, 16 and 20 V |
| Dual supply | Plus or minus 2.5, 5 and 10 V |
| On resistance | 125 ohms typical at 15 V |
| On capacitance and bandwidth | 18 pF typical, 25 MHz |
| Leakage | Plus or minus 10 pA typical at 15 V |
| Switching | Break before make |
Why two channels sharing an address is a feature
On a differential signal, both halves of the pair have to switch at the same instant, and the CD4052B does that because one set of address lines drives both 4 to 1 switches. Two CD4051B parts driven from the same logic would need matched propagation and matched trace length to do the same job, and they would still sit on two dies with two sets of on resistance. One die with two channels gives the pair a shared substrate and shared thermal drift, which is the property that makes the part usable for a differential multiplexer ahead of an instrumentation amplifier.
The same property is used to switch a stereo pair, a two wire sensor loop or an I and Q pair from a quadrature detector. In each case the two channels have to move together and the board gains nothing from independent control, so the shared address pins save two logic lines per switch on a board with several multiplexers.
On capacitance and the settling budget
Eighteen picofarads of on capacitance is lower than the 30 picofarads of the single 8 channel part, because each channel in a 4 to 1 switch has fewer neighbours and a shorter internal path. That matters when the multiplexer feeds an analogue to digital converter: the sample and hold capacitor of the converter and the on capacitance of the switch charge share, so a 12 bit converter with a 10 picofarad hold capacitor loses a measurable fraction of the signal when it samples through a 125 ohm switch and an 18 picofarad path.
The cure is a buffer between the switch and the converter, and the buffer also removes the on resistance from the error budget. A board that samples directly through the multiplexer is trading accuracy for component count, and the arithmetic of that trade is the vendor's settling time curve, which this page does not quote because the document carries it as a graph rather than as a table.
Bandwidth at 25 MHz and what it means
The 25 MHz figure is a small signal bandwidth into a defined load, and it is higher than the 20 MHz of the 8 channel part because of the lower on capacitance. It is not a digital bandwidth and it does not mean the part can pass a 25 MHz clock without distortion. It means a signal at a few hundred kilohertz passes with little attenuation, and a signal at a few megahertz begins to roll off. A board multiplexing baseband audio or a slow sensor sees no effect; a board multiplexing an intermediate frequency of 10.7 MHz sees attenuation and phase shift that have to be measured rather than assumed.
Address lines, inhibit and the two channel linkage
Two address pins select one of four inputs per channel, and an inhibit pin turns both channels off together. That is the whole control interface: four pins and no decoding to worry about. On a board with several multiplexers, the address lines can be bused and the inhibit lines kept separate, which lets a controller enable one part at a time and leave the rest of the bus parked. The common pins of the disabled parts then see a high impedance rather than the leakage of a selected channel.
The linkage between the two channels is the part of the behaviour that a bill of materials cannot express. Both channels always sit on the same input number, so a differential pair stays a pair and a stereo pair stays in step. A board that needs channel one on input three while channel two sits on input one is not a 4052B application, and the fix is either two 4051B parts or the three switch architecture of the 4053B. On a four layer card, two 4051B parts cost 118 square millimetres in SOIC against 59 for one 4052B, so the wrong choice is paid for in board area as well as in part count, and that arithmetic is worth doing before the drawing is frozen rather than after, and it is cheaper than a copper revision later.
Reel planning and the tube that is gone
With CD4052BM obsolete, the only SOIC format is the 2500 piece reel, and the surface mount alternatives are the 2000 piece SOP and TSSOP reels. A build of 300 boards with two multiplexers each needs 600 pieces, which is a quarter of a reel. That is a cut reel with a printed label, and it is the normal answer for a first production run.
For a product with a long life, the question is not the first run but the tenth, and the answer depends on whether the reel row survives. The last time buy and LTB planning page sets out how a final order is sized, and the component obsolescence management page covers how a family that has already lost three SOIC rows is monitored for the next one.
What to send with an enquiry
Send the rails, whether the two channels are used as a differential pair, the number of multiplexers per board and the annual quantity. If the pair is differential, say so, because the shared address line is the reason the part was chosen and a replacement has to preserve it. If the board is surface mount and the drawing names the obsolete tube row, the reel is the live format and the quantity question follows from it. The pin to pin cross reference page covers the bodies that share the 16-lead pinout.