CD4051BM
Product Specifications
CD4051BM
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4051BM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4051BM: the SOIC tube row that no longer appears in the addendum
The CD4051BM is the small outline tube entry in this catalogue for the CD4051B single 8 channel analogue multiplexer. The die is the familiar one: one channel, 8 to 1 configuration, on-chip binary address decoding, 3 V to 20 V digital control independent of the analogue rails, a typical on resistance of 125 ohms at 15 V, a bandwidth of 20 MHz and a continuous channel current of 10 milliamps. The vendor marks the family ACTIVE and describes it as a 20 V, 8 to 1, single channel analogue multiplexer.
The string is where the trouble starts. The package option addendum dated 26 September 2026 lists the CD4051B family across 16 rows: the plastic DIP as BE and BE.A, the ceramic body as BF, BF.A, BF3A and BF3A.A, the SOIC body as BM96 and BM96.A, the SOP body as BNSR and BNSR.A, the TSSOP body as BPWR and BPWR.A, plus two military drawing rows. There is no CD4051BM row at all, not even an obsolete one. The nearest row that does exist is CD4051BM96, the same body on a 2500 piece reel, and the obsolete rows BMT, BM96G3 and BM96G4 show that the tube format died while the reel survived.
The CD4051B rows as the vendor addendum publishes them
| Part class | Single 8 channel analogue multiplexer and demultiplexer |
| Vendor document | SCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B |
| Package addendum date | 26 September 2026 |
| Tube rows published | None in the SOIC body, the D body exists only on reels |
| SOIC reel row | CD4051BM96, 2500 pieces, marking CD4051BM |
| Second SOIC reel row | CD4051BM96.A, same quantity and marking |
| Obsolete SOIC rows | CD4051BMT, CD4051BM96G3, CD4051BM96G4, quantity blank, Call TI |
| SOP reel row | CD4051BNSR, 2000 pieces |
| TSSOP reel row | CD4051BPWR, 2000 pieces, marking CM051B |
| Obsolete TSSOP row | CD4051BPW, quantity blank, Call TI |
| PDIP row | CD4051BE, 25 pieces in a tube |
| Ceramic rows | CD4051BF, CD4051BF.A, CD4051BF3A, CD4051BF3A.A |
| Military drawing rows | 7901502EA and 8101801EA, CDIP, 25 pieces |
| On resistance | 125 ohms typical at 15 V |
| Leakage | Plus or minus 10 pA typical, 0.3 microamps maximum |
| Bandwidth | 20 MHz, on capacitance 30 pF typical |
| Supply | 3 V to 20 V single, plus or minus 3 V to plus or minus 10 V dual |
| Current limit | 10 milliamps continuous per channel |
| Body size | SOIC 16 leads, 59.4 square millimetres |
| Lead finish on the reel row | NIPDAU, moisture level 1 at 260 degrees |
| Operating range | Minus 55 to plus 125 degrees |
The prototype problem this row creates
A tube of 50 pieces used to be the way a prototype build got its multiplexer. With the tube row gone, the smallest published quantity in the SOIC body is 2500 pieces. That is a real cost for a board that is being built in tens, and it is the reason so many small builds move to the SOP or TSSOP reel at 2000 pieces instead, or to the plastic DIP that still ships in a 25 piece tube.
None of those moves is a drop-in. The SOP body is 79.56 square millimetres at 10.2 by 7.8 millimetres, the TSSOP body is 32 square millimetres at 5 by 6.4 millimetres, and the SOIC body is 59.4 square millimetres at 9.9 by 6 millimetres. Three different footprints, three different stencil apertures and, in the TSSOP case, a 0.65 millimetre pitch that changes the assembly process window. A purchasing change of suffix is therefore a board change, whether or not anyone says so on the change note.
Reading the addendum correctly
The row that is missing is as informative as the rows that are present. CD4051BMT is obsolete, CD4051BM96G3 and CD4051BM96G4 are obsolete, and the plain tube and the two older reel suffixes are gone while BM96 and BM96.A remain Active at 2500 pieces. That pattern is a catalogue cleanup rather than a die change: the vendor consolidated the SOIC body onto one reel suffix and dropped the rest.
The practical consequence is that a purchasing system which holds CD4051BM will keep returning a lead time of never while the identical die sits on a reel one line below. Reconciling the two is a five minute job with the addendum in hand and a week of silence without it. That is why this page prints the rows rather than a summary.
Where the part is used and why 20 V still matters
The 4051B family is chosen today for three jobs: switching a signal that swings beyond the logic supply, switching a signal on a board that has no negative rail available for a modern switch, and replacing a mechanical relay in a low current signal path. A plus or minus 10 V analogue range with 3 V to 20 V control covers all three, and the break before make behaviour keeps two channels from shorting a source together during the address change.
The 10 milliamp current limit and the 125 ohm on resistance set the boundaries. A channel can carry a sensor signal, a reference divider tap or a low current transducer bias; it cannot carry an actuator. Leakage of 10 picoamps typical is the figure that makes the part usable ahead of a high impedance amplifier, and the quiescent power of 0.2 microwatts is why it appears in battery instruments that stay biased for years.
What to do with a drawing that names the missing row
Three routes exist. Take the reel and accept 2500 pieces, which is right for a production line and wrong for a pilot. Move to the SOP or TSSOP reel and change the copper, which is right when the board is being revised anyway. Or take the plastic DIP and change the assembly process, which is right for a hand built instrument. The component obsolescence management page covers how those three routes are compared on a real bill of materials, and the kitting service page explains how a partial reel is split across two builds without leaving an unlabelled remnant on the shelf.
If the board can accept a modern switch, the TMUX4051 is the vendor's own drop-in claim against this family, with 1.8 V logic and a smaller body, but it runs on plus or minus 12 V rather than the plus or minus 10 V of the original. The obsolete part cross reference hub collects the pages for that comparison across the 4051B, 4052B and 4053B family.
Checking a stock claim against the addendum
Because the tube string is absent from the vendor list, a distributor that reports CD4051BM in stock is either holding an old tube from before the row closed or quoting the reel string loosely. Both happen, and the way to tell them apart is the label rather than the reply. A tube from the closed row carries a build date before the consolidation; a reel labelled BM96 that has been cut carries a new label with a quantity that is not 2500. Either can be supplied, and neither should be presented as a current production tube row.
For a buyer the check is three questions: what is the full orderable string on the label, what quantity and carrier does the label state, and what date code sits beside it. A supplier who answers all three from the reel rather than from a catalogue is a supplier who can be scheduled against. That is the difference this page is trying to make visible, since the bare string on a drawing no longer resolves to a body.
What to send with an enquiry
Send the string exactly as it appears on the drawing, the analogue rails, the quantity for the next build and the quantity for the build after it. With those four items the answer can name a body rather than a suffix, and it can be costed against a reel size instead of a hope. If the drawing is going to be revised anyway, say which body the board can accept and the enquiry can be quoted both ways in one pass.