Contact Us

CD4051BE

Brand: Texas Instruments
Texas Instruments CD4051BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4051BE — Power Management & Signal Chain | Superb Automation

CD4051BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4051BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4051BE: the 8 to 1 analogue multiplexer in the 16-lead plastic DIP

The CD4051BE is the plastic dual in line member of the CD405xB family, a single 8 channel analogue multiplexer and demultiplexer with on-chip binary address decoding and logic level conversion. The vendor describes it in one line as a 20 V, 8 to 1, single channel analogue multiplexer and marks it ACTIVE. The parametric table gives one channel, a configuration of 8 to 1, single supply options of 3.3, 5, 12, 16 and 20 V, dual supply options of plus or minus 2.5, 5 and 10 V, a typical on resistance of 125 ohms, a typical on capacitance of 30 picofarads, a maximum on state leakage of 0.3 microamps, a typical supply current of 0.04 microamps, a bandwidth of 20 MHz and a continuous input or output current of 10 milliamps.

The E suffix is what this row is about. The package option addendum dated 26 September 2026 lists CD4051BE as Active and in production, 16 leads in a plastic DIP, 25 pieces to a tube, RoHS yes with a nickel palladium gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, an operating range of minus 55 to plus 125 degrees and the marking CD4051BE. The .A row of the same string sits beside it at the same 25 piece tube, and the military drawing rows 7901502EA and 8101801EA sit in the ceramic body at 25 pieces with a tin lead finish.

The CD4051BE row as the vendor addendum publishes it

Part classSingle 8 channel analogue multiplexer and demultiplexer
Vendor descriptor20 V, 8 to 1, single channel analogue multiplexer
Vendor documentSCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B
Configuration8 to 1, one channel, bidirectional signal path
Digital input range3 V to 20 V, independent of the analogue supply
Analogue signal rangeUp to 20 V peak to peak
Single supply3 V to 20 V, performance degrades below 3 V
Dual supplyPlus or minus 3 V to plus or minus 10 V
On resistance125 ohms typical at a 15 V supply over the input range
On state leakagePlus or minus 10 pA typical at 15 V, 0.3 microamps maximum
Quiescent power0.2 microwatts typical
Bandwidth20 MHz
On capacitance30 picofarads typical
Continuous current10 milliamps maximum through any channel
SwitchingBreak before make
ESD3000 V HBM, 2000 V CDM
Package for this codePDIP (N), 16 leads, 181.42 square millimetres
Packing25 pieces in a tube
Lead finishNIPDAU
StatusActive, production
Part markingCD4051BE
SOIC reel rowCD4051BM96, 2500 pieces, marking CD4051BM
TSSOP reel rowCD4051BPWR, 2000 pieces, marking CM051B
Obsolete rows of the familyCD4051BMT, CD4051BPW, CD4051BM96G3 and CD4051BM96G4

Logic level conversion is the reason this part survives

The digital control pins accept 3 V to 20 V whatever the analogue rails are doing. On a board that switches a plus or minus 10 V signal from a 3.3 V microcontroller, that property removes the level shifter that a modern analogue switch would need, and it is the single feature that keeps the 4051B family in new bills of materials rather than only in legacy ones. The vendor states the digital range separately from the analogue range precisely because the two are independent.

The analogue path is bidirectional, so the same body works as an 8 to 1 multiplexer or as a 1 to 8 demultiplexer without a second part number, and the binary address decoding is on chip, which means three control lines select one of eight channels and nothing else is needed between the microcontroller and the switch. The 10 milliamp continuous current limit is the figure that decides whether the part can carry a sensor supply as well as a signal: it can switch a small load, and it cannot switch a relay.

On resistance and what it does to a measurement

125 ohms typical at 15 V sounds high against a modern switch at 1 ohm, and for a current measurement it is unusable. For a voltage measurement into a high impedance instrument amplifier it barely matters, because the switch resistance sits in series with an input that draws nanoamps. The vendor also publishes the leakage, plus or minus 10 picoamps typical at 15 V, which is the number that decides the error floor: 10 picoamps through a 1 megohm source resistance is 10 microvolts of offset, and that is the budget a data acquisition front end has to live inside.

On resistance is not flat over the signal range, which is why the part suits ratiometric measurement and switching of matched channels more than precision attenuation. Two channels of the same die track each other, so a differential pair built from two channels of a CD4052B cancels most of the resistance variation, while a single channel used as a variable attenuator does not. The vendor publishes the on resistance at 15 V and does not publish a flatness figure for every supply in text, so a circuit that depends on flatness has to be measured on the bench.

Where the plastic DIP body still wins

A through-hole multiplexer is the right choice on a board that is assembled by hand, on a socket that lets a failed switch be replaced in the field, and on a test fixture where the multiplexer sits on a plug in card. The body is 181.42 square millimetres at 19.3 by 9.4 millimetres, which is five times the area of the TSSOP body, and the tube of 25 is not a pick and place format. What it does offer is a lead pitch that any technician can probe and a package that survives repeated insertion far better than a 0.65 millimetre pitch body.

Instrumentation built in tens rather than thousands is the typical home for this row: an environmental chamber controller, a calibration bench, a data logger with eight thermocouples. In those quantities the tube of 25 is roughly one build, and the absence of a reflow profile and a moisture bake is worth more than the board area.

Replacement routes and what is published

The vendor lists two successors against this family. The TMUX4051 is described as a plus or minus 12 V, 8 to 1 analogue multiplexer with 1.8 V compatible logic in smaller packages, and the product page marks it a drop-in replacement with upgraded functionality. The SN74LV4051A is described as a pin for pin part for 5 V or lower applications. Neither is a drop-in on a plus or minus 10 V rail, and the page says so rather than presenting the newer part as a universal swap.

A customer who has to keep the plus or minus 10 V swing stays on the CD4051B, and a customer who can drop to a 12 V single rail gains the 1.8 V logic interface and a smaller footprint. The decision is usually made by the existing board rather than by the price. The pin to pin cross reference page sets out which of the two routes keeps the footprint, and the drop in replacement verification page covers the tests that prove the replacement rather than assume it.

What to send with an enquiry

Send the string as written, the analogue rails, the number of channels the board needs and the annual quantity. If the board is through-hole, say whether it is socketed, because a socketed board can take the .A row as well and that widens the available stock. If the board is surface mount and the drawing still says CD4051BM without the reel suffix, read the row above on this page first, since that string is the one with the availability problem. The one stop BOM sourcing page explains how a mixed through-hole and surface mount bill is consolidated into one order.