CD4047BM96
Product Specifications
CD4047BM96
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4047BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4047BM96: the 14-lead SOIC multivibrator on a 2500 piece reel
The CD4047BM96 is the small outline member of the CD4047B family on a 2500 piece large reel, and it is the row a pick and place line actually buys. The die is the same CMOS multivibrator that runs as a one shot or a free running oscillator with one resistor and one capacitor, described by the vendor as a CMOS low power monostable and astable multivibrator and marked ACTIVE. The parametric table gives one channel, standard CMOS input, push pull output, 600 microamps of supply current, 4 milliamps of sink and 4 milliamps of source current.
The packaging detail is where this row differs from its family. The addendum dated 18 September 2026 lists CD4047BM96 as Active, SOIC body with 14 leads, 2500 pieces on a large tape and reel, RoHS yes, nickel palladium gold finish, moisture level 1 at 260 degrees with unlimited floor life, and the marking CD4047BM. The tube version of the same body, CD4047BM, is listed as Obsolete with a blank quantity and a Call TI instruction, which is the single most important fact on this page for anyone holding an old drawing that names the BM string without the reel suffix.
The CD4047BM96 row as the vendor addendum publishes it
| Part class | CMOS low power monostable and astable multivibrator |
| Vendor document | SCHS044C, revised September 2003, acquired from Harris Semiconductor |
| Package for this code | SOIC (D), 14 leads, 51.9 square millimetres at 8.65 by 6 mm |
| Packing | 2500 pieces on a large tape and reel |
| Status | Active, production |
| RoHS | Yes |
| Lead finish | NIPDAU |
| Moisture level | Level 1 at 260 degrees, unlimited floor life |
| Part marking | CD4047BM |
| Sibling rows on the same reel | CD4047BM96.A and CD4047BM96G4, same body and quantity |
| Obsolete tube row | CD4047BM, quantity blank, Call TI |
| Other surface mount rows | CD4047BNSR 2000 piece reel in SOP, CD4047BPWR 2000 piece reel in TSSOP |
| Obsolete TSSOP row | CD4047BPW, quantity blank, Call TI |
| Supply range | 3 V to 18 V, with 5 V, 10 V and 15 V parametric ratings |
| Supply current | 600 microamps maximum |
| Output drive | 4 mA sink and 4 mA source |
| External parts | One resistor and one capacitor |
| Monostable trigger | Positive or negative edge, retriggerable option |
| Astable accuracy | Plus or minus 2 per cent plus 0.03 per cent per degree at 100 kHz |
| Trimmed accuracy | Plus or minus 0.5 per cent plus 0.015 per cent per degree at 10 kHz |
| Operating range | Minus 55 to plus 125 degrees |
Why the reel size is the real specification
A 2500 piece reel sets the minimum practical order for a production build. A line that needs 800 pieces takes a partial reel and pays for the handling, or takes a full reel and carries 1700 pieces of safety stock that has to be rotated. The alternative in this family is the tube that no longer exists, so the choice is between a partial reel and a reel split across two builds. Both are workable, and neither is visible on a bill of materials that names only the base string.
Moisture level 1 matters here for a different reason than it does on a fine pitch part. Level 1 with unlimited floor life means the reel can sit on a shelf and be mounted without a bake cycle, which removes one scheduling constraint from a build that is already waiting on a timing component. A part at level 3 would need the reel sealed, the humidity indicator checked and a 24 hour bake after a single shift out of the bag. On a high mix line that difference decides whether the reel can stay kitted overnight.
Timing behaviour worth reading before the first build
In monostable mode the output pulse width is set by the external resistor and capacitor and is independent of the trigger width, with a retriggerable option that extends a pulse while the trigger repeats. The vendor also states that the pulse width accuracy holds at duty cycles approaching 100 per cent and that the recovery time is essentially independent of the pulse width, which is what allows the part to run as a nearly continuous one shot in a watchdog or a missing pulse detector.
In astable mode the same two parts set a 50 per cent duty cycle free running frequency, gateable through the ASTABLE pin, with the oscillator output available separately. The accuracy windows are plus or minus 2 per cent plus 0.03 per cent per degree at 100 kHz and plus or minus 0.5 per cent plus 0.015 per cent per degree at 10 kHz when trimmed at 10 V. A 10 kHz timer built from a 5 per cent capacitor will not hold better than the capacitor allows, so the tighter window only becomes real when the passive parts are chosen for it.
Package comparison across the family
The SOIC body is 51.9 square millimetres, the SOP body 79.56 square millimetres, the TSSOP body 32 square millimetres and the PDIP body 181.42 square millimetres. For a new board the SOIC at 1.27 millimetre pitch is the easiest surface mount body to inspect and rework, which is why it remains the default for industrial control boards that are built in the thousands rather than the millions. The TSSOP saves 20 square millimetres and costs 0.65 millimetre pitch, and the SOP is wider than the SOIC without being easier to place.
All three surface mount rows carry the same die and the same electrical table, so the choice is mechanical and commercial rather than electrical. The only electrical difference between rows in this family is none: the vendor does not publish a separate parametric set for the SOIC body. What does differ is the floor life record on the reel label and the reel quantity, and both of those affect how a build is scheduled rather than how the circuit behaves. A line that keeps three bodies on the shelf for the same timer keeps three reel sizes, three part markings and three sets of feeder settings, which is often the reason a purchasing team standardises on one row and lets the others go.
Availability and the LTB question
Because the tube row is gone while the reel row is Active, the parts most at risk are the small quantities: repair lines, pilot builds and engineering samples. Those quantities used to come from a 50 piece tube and now come from a reel. A buyer who plans the final order for a legacy product should size it against the remaining build life rather than the next twelve months, which is what the last time buy and LTB planning page sets out in detail.
Where a board can accept a different body, the cross reference route is faster than a last time buy. The pin to pin cross reference page covers the three surface mount bodies of this family and the footprint change each one needs, and the obsolete part cross reference hub collects the other timer and multivibrator families with the same problem.
What to send with an enquiry
Send the base string, the mode, the timing value and the build quantity. If the line is a repair or a pilot, say how many pieces are needed and when, because the reel size drives the answer more than the unit price does. If the board is already qualified with the tube body, say that too, because the reel body is the same die and the qualification usually carries over with a paper review rather than a new test campaign. The one thing worth confirming in writing is the reel quantity, since 2500 pieces against a build of 600 leaves inventory that has to be carried or resold. A partial reel, cut and re-sealed with the label intact, is the usual answer on a first build.