Contact Us

CD4030BE

Brand: Texas Instruments
Texas Instruments CD4030BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4030BE — Power Management & Signal Chain | Superb Automation

CD4030BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4030BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4030BE: four exclusive-OR gates in a 14-lead plastic DIP

CD4030BE is the quad exclusive-OR of the CD4000B family, four independent 2-input XOR gates in a 14-lead plastic DIP, 25 pieces to a tube. The vendor descriptor reads quadruple 2-input 3 V to 18 V exclusive-OR gates, the document is the CD4030B data sheet revision C, and the feature line gives a 65 ns typical propagation delay, a quiescent current tested to maximum at 20 V, 5 V, 10 V and 15 V parametric ratings, an input current maximum of 1 microamp at 18 V and noise margins of 1 V, 2 V and 2.5 V at the three rails. The parametric table gives four channels, two inputs per channel, 6.8 mA sink and source and an 8 Mbps data rate.

The addendum lists CD4030BE as Active in production, PDIP (N) with 14 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4030BE. The SOIC rows behave differently from the rest of the family: CD4030BM is Obsolete, CD4030BM96 is Active at 2500 pieces, and the SOP and TSSOP rows are both on Last Time Buy, which makes the reel and this DIP the two formats with a future.

The CD4030BE row as the vendor addendum publishes it

Part classQuad 2-input exclusive-OR gate
Vendor descriptorQuadruple 2-input 3 V to 18 V exclusive-OR gates
Vendor documentCD4030B data sheet revision C
Supply range3 V to 18 V
Parametric ratings5 V, 10 V and 15 V tables
Propagation delay, vendor figure65 ns typical
Output drive, parametric table6.8 mA sink and source
Data rate, parametric table8 Mbps
Input current, maximum1 microamp at 18 V over the full range, 100 nA at 25 degrees
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
Quiescent currentTested to maximum at 20 V on every unit
Package for this codePDIP (N), 14 leads
Packing25 pieces in a tube
Lead finishNIPDAU
Moisture levelNot applicable for this package type
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4030BE
SOIC rowsCD4030BM Obsolete, CD4030BM96 Active at 2500 pieces
SOP rowCD4030BNSR, Last Time Buy
TSSOP rowCD4030BPWR, Last Time Buy, marking CM030B
Ceramic rowsCD4030BF and CD4030BF3A, 25 piece tube

A controlled inverter, a comparator bit and an edge detector

An exclusive-OR with one input tied high inverts the other input, which turns four gates into four programmable inverters, and that is the most common use of the part in a legacy board: a bus that is either passed through or complemented, depending on one control line. With one input tied low the gate passes the other input unchanged, so four gates can either buffer or invert four lines under a single control.

The second use is comparison. An XOR of two bits is high when the bits differ, so four gates compare four bit pairs in parallel, and an OR of the four outputs says whether two words differ at all. That is the front end of a digital comparator, and it is the reason the 4030 appears in address decoding and in test fixtures that check a pattern.

The third use is edge detection. An XOR of a signal with a delayed copy of itself produces a pulse on every transition, which a counter can then use to count events rather than levels. The delay is provided by an RC network or by a gate, and the pulse width is set by that delay rather than by the XOR itself.

The 65 ns figure and the 6.8 mA drive

The propagation delay is 65 ns typical, slightly longer than the 60 ns of the NAND and NOR gates in the same family, which is expected because an XOR is two gate levels internally. The parametric table pairs that with 6.8 mA of drive and an 8 Mbps data rate, so the part sits in the same speed class as the rest of the quad gates and well below anything that would be called fast today.

The drive is enough for four CMOS inputs, a small transistor base or an LED at a few milliamps. It is not enough for a bus that has to charge a long trace quickly, and a board that uses the XOR as a line driver should check the load against the 65 ns figure, which is quoted into a light load rather than into a cable.

The two rows on last time buy, and what that means for a build

The addendum marks the SOP and TSSOP rows of this family as Last Time Buy, while the SOIC reel and the plastic DIP remain active. A board that was laid out for the TSSOP body, which is the smallest of the four, cannot simply switch to the SOIC without a board change, and the last time buy window is the point at which the stock for that body has to be committed. A board that has years of production left should either move to the SOIC reel now or plan a stock buy for the TSSOP body.

The plastic DIP is not affected by that decision, because the addendum lists it as Active at 25 pieces. A repair and prototype route that uses the DIP can continue while the surface mount question is settled, which is often the cheapest way to keep a legacy line running during a qualification.

Where the 4030 sits against the 4070 and the 4077

The CD4070B is the other quad XOR in the family, with a different pinout in the same 14-lead body, and the CD4077B is the quad exclusive-NOR, which is the inverted version. The 4030 and the 4070 are functionally the same gate and differ in pin assignment, which matters when a board is being repaired and the wrong one is fitted: the part works in some sockets and not in others, and the failure looks like a wiring fault.

An exclusive-NOR is the right gate for an equality test, because its output is high when the bits match, while the XOR is the right gate for a difference test. A comparator built from 4030 gates needs an inverter on the final OR, and one built from 4077 gates does not.

Incoming checks on an exclusive-OR line

The functional test is the four row truth table per gate, and the row that matters is the one with both inputs high, because that is the row a part with a stuck input passes by accident. The marking check separates the 4030 from the 4070, which are the same function in a different pinout and are easy to mix in a parts drawer. The date code check follows the family rule.

The reference pages are the incoming inspection plan, the pin to pin cross reference for the 4030 against 4070 question, and the last time buy and LTB planning page for the SOP and TSSOP rows.

Questions that come up on the 4030

Whether the part can be used as a phase detector. It can, in the simple form where the XOR output is filtered to give a voltage proportional to the phase difference, with the limitation that the range is half a cycle and the output has a ripple at twice the input frequency.

Whether the 4030 can replace a 4070. It cannot in an existing socket without checking the pinout, because the two parts assign the gates to different pins.

Whether the outputs can be paralleled. They can be paralleled as logic, but the two gates switch at slightly different times and share the current unevenly, so the practice is reserved for light loads.

Whether the last time buy affects the DIP. It does not, and the DIP row is Active at 25 pieces while the SOP and TSSOP rows have to be committed before the window closes.