CD4026BE
Product Specifications
CD4026BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4026BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4026BE: a decade counter with a seven segment decoder in a 16-lead DIP
CD4026BE is the through-hole member of the CD4026B family, a decade counter and seven segment decoder in one 16-lead plastic DIP, 25 pieces to a tube. The vendor descriptor reads CMOS Decade Counter and Divider with Decoded 7-Segment Display Outputs and Display Enable, and the feature line gives fully static counter operation from DC to 6 MHz typical at 10 V, Schmitt triggered clock inputs, a quiescent current tested to maximum at 20 V, 5 V, 10 V and 15 V parametric ratings, and JEDEC 13B conformance. The die holds a five stage Johnson counter and a decoder that turns the Johnson code into seven segment outputs.
The addendum lists CD4026BE as Active in production, PDIP (N) with 16 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4026BE. The document is the CD4026B and CD4033B data sheet revision B, and the same family carries the SOIC, SOP and TSSOP rows that the rest of the 4000B range uses.
The CD4026BE row as the vendor addendum publishes it
| Part class | Decade counter with seven segment decoder and display enable |
| Vendor descriptor | Decade counter and divider with decoded 7-segment outputs |
| Vendor document | CD4026B and CD4033B data sheet revision B |
| Counting rate, vendor feature line | DC to 6 MHz typical at 10 V |
| Operation | Fully static |
| Clock input | Schmitt triggered |
| Outputs | Seven decoded segment outputs plus carry out |
| Control inputs | Clock inhibit, reset, display enable in and out |
| Supply range | 3 V to 18 V |
| Parametric ratings | 5 V, 10 V and 15 V tables |
| Output type | Push pull, balanced outputs |
| Input type | Standard CMOS |
| Quiescent current | Tested to maximum at 20 V on every unit |
| Package for this code | PDIP (N), 16 leads |
| Packing | 25 pieces in a tube |
| Lead finish | NIPDAU |
| Moisture level | Not applicable for this package type |
| Operating range | Minus 55 to plus 125 degrees |
| Status | Active, production |
| Part marking | CD4026BE |
| SOP row | CD4026BNSR, 2000 piece reel |
| TSSOP rows | CD4026BPW Obsolete, CD4026BPWR Active at 2000 pieces, marking CM026B |
| Sibling part in the document | CD4033B, latch and ripple blanking variant |
A counter and a decoder that share one package
The decoder converts the Johnson counter state into the seven segment pattern, so the part drives a display without a separate decoder package. That saves one package and one bundle of traces on a board that has to show a decimal digit, and it is the reason the 4026 survives in panel meters, timers and test instruments that were laid out when a microcontroller with a display driver cost far more than two logic packages.
The display enable input blanks the display without stopping the count, which is how a multiplexed display is built: the counter keeps counting, the enable line pulses the digit on and off, and a second digit is driven from the carry out of the first. The enable output passes the blanking to the next package in the chain, so a row of digits blanks together when the first one does.
Segment drive and the limit that decides the display
The resistor per segment is what sets the display current, and it is also what protects the output stage from a display that fails short. A 330 ohm resistor on a 5 V rail gives about 9 mA into a red segment after the forward drop, which is at the top of what the family output can give, and a 1 k resistor gives about 3 mA, which is dim in daylight and adequate on a panel. A display that has to be readable outdoors needs a driver stage rather than a smaller resistor, because the output current is the limit rather than the resistor.
Each segment output is a logic output with the family drive, and a small seven segment LED with a series resistor per segment can be driven directly at a low current. A larger display, a high brightness display or a multiplexed display with a short duty cycle needs more current than the output can give, and the usual answer is a transistor per segment or a driver array. The current that can be taken from the package also sets the supply decoupling requirement, because eight segments switching at once draw a pulse that a ceramic capacitor at the package has to supply.
One thing the part does not do is latch the display data. The outputs follow the counter, so during a count the display shows intermediate states rather than a clean change from one digit to the next. The CD4033B, which shares the same document, adds a latch and ripple blanking for exactly that reason. A display that must change cleanly takes the 4033, and a display that can show transition states takes the 4026.
Counting, chaining and the carry out
The counter is a five stage Johnson type, which is the same structure as the CD4017B but with a decoder instead of ten decoded outputs. The carry out pulses once per ten counts and can drive the clock of the next package, so a two digit display is two packages and no external logic. The reset input clears the count to zero and is asynchronous, so a reset button or a power up pulse works without a clock.
The Schmitt triggered clock is the detail that makes the part usable with a mechanical counter input, a reed switch or a slow optical sensor. Without it, a slow edge would produce several counts per event, which on a counter driving a display looks like the display skipping numbers. With it, the count follows the events rather than the edges.
Where the 4026 sits against the 4017 and the 4033
The CD4017B gives ten separate decoded outputs and no display decoding, which suits a sequencer rather than a display. The CD4033B gives the seven segment outputs plus a latch and ripple blanking, which suits a display that must be stable. The CD4026B sits between them: seven segment outputs without a latch, for a display that can follow the count in real time. The CD4029B is the presettable up and down counter, which suits a count that has to start from a set value.
A board that needs a numeric display and a stable reading takes the 4033, a board that needs a live count takes the 4026, and a board that needs ten discrete steps takes the 4017. The three are close enough in cost that the choice is made by the display behaviour rather than by the price.
Incoming checks on a display counter
The functional check walks the count from zero to nine and verifies each of the seven segment patterns against the data sheet, because a segment that is missing or extra still produces a plausible digit at some counts. The display enable check is separate: pulling the enable input should blank the display without stopping the counter, and a part that stops counting when blanked is a different fault. The marking check separates the plastic DIP from the SOIC and from the sibling 4033, which is a different part in the same body.
The reference pages are the incoming inspection plan, date code management, and the pin to pin cross reference when a legacy display board needs a second source.
Questions that come up on the 4026
Whether the part can drive a liquid crystal display. It cannot, because an LCD needs an AC drive waveform rather than a DC segment level, and a 4026 driving one would destroy the display over time.
Whether the counter can be reset without stopping the display. It can, because reset clears the count while the display outputs follow the count, so the display shows zero after the reset.
Whether two digits can share one display enable line. They can, with the enable output of the first feeding the enable input of the second, which is how a row of digits blanks together.
Whether the 6 MHz figure applies at 5 V. It does not, and the 5 V rate is lower; the figure quoted is at 10 V, and a 5 V circuit should work from the 5 V table rather than from the feature line.